summaryrefslogtreecommitdiff
path: root/board/freescale
Commit message (Collapse)AuthorAgeLines
* MLK-10774-39 imx:mx6qsabreauto update video settingsPeng Fan2015-04-29-7/+91
| | | | | | Update video settings Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-38 imx: fix ecspi codePeng Fan2015-04-29-0/+20
| | | | | | | | | | | This commit 155fa9af95ac5be857a7327e7a968a296e60d4c8 "spi: mxc: fix sf probe when using mxc_spi" introduces "board_spi_cs_gpio" function to discard gpio in CONFIG_SF_DEFAULT_CS for spi flash. Follow this rule to make imx boards work fine. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10448-6 imx: mx6qpsabreauto: Add MX6QP SABREAUTO CPU3 board supportYe.Li2015-04-29-1/+339
| | | | | | | | | | | | | | | | | | 1. Add DDR script v1.04 for i.MX6DQP SABREAUTO board. 2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9] and init the enet pll output to 125Mhz. 3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN. Build target: mx6qpsabreauto_config Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Robin Gong <b38343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit e0b316f071aa17c8e41a50f395346ab9f012e665) Conflicts: board/freescale/mx6qsabreauto/mx6qsabreauto.c boards.cfg
* MLK-10446: mx7d_12x12_lpddr3_arm2: Enable 1.8V on PHY ctrlFabio Estevam2015-04-29-2/+0
| | | | | | | | | | Enable 1.8V on PHY control, so that Gigabit PHY operation can be functional. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com> (cherry picked from commit a17f1300a1b6d3b46a090baa84ba2fef104a1af6) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-37 imx:mx7d fix qspi probe errorPeng Fan2015-04-29-6/+6
| | | | | | We should use CONFIG_FSL_QSPI, but not CONFIG_QSPI Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-35 imx:mx7 use power_init_boardPeng Fan2015-04-29-80/+48
| | | | | | | Upgrade to upstream way, using power_init_board. Add pfuze300 support. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10385-4 imx: mx7dsabresd: Add board codes for NAND flash supportYe.Li2015-04-29-22/+25
| | | | | | | | | | | | | | | Update board codes to support GPMI NAND flash. Since the GPMI NAND needs board rework, it is disabled at default. Two ways to enable GPMI NAND: 1. Define CONFIG_SYS_BOOT_NAND for NAND boot case 2. Modify the line 306 in mx7dsabresd.h from QSPI to NAND. #define CONFIG_SYS_USE_QSPI /* Enable the QSPI flash at default */ to #define CONFIG_SYS_USE_NAND /* Enable the NAND flash at default */ Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 5db03facf3add6a95728bc97ac2300003a103932) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10363-3 Android: Add android support for MX7D SABRESD boardYe.Li2015-04-29-0/+103
| | | | | | | | | | | | Enable android fastboot, recovery, booti features for mx7d sabresd board by using new build target: mx7devkandroid_config Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit bfc2b467ddac9c6eccb3f39aad3663a959546b64) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: boards.cfg
* MLK-10774-33 imx:mx6 add udc and fastboot supportPeng Fan2015-04-29-1/+667
| | | | | | | | | | | | Add udc and fastboot support We did not use the upstream way. Currently use CI_UDC and USB_GAGDET of upstream can make fastboot work, but lack of flash operation, so we still use our way. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10774-32 imx:mx6slevk inlcude crm_regs.hPeng Fan2015-04-29-0/+1
| | | | | | Add missed included header file crm_regs.h Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10215 Add elan init in i.MX6SL-EVK boardHaibo Chen2015-04-29-0/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | EPDC board contain a elan touch screen, this screen is a i2c slave. If this EPDC board connect to i.MX6SL-EVK board, after uboot boot up, if we do i2c operation, like i2c probe, then the i2c bus block. This is due to the elan touch screen i2c slave. This device needs to do some initialization opearation before its i2c operation, otherwise this i2c device pull down the i2c clk line, and make the i2c bus hang. This means elan needs a special flow on i2c before its address is acked, otherwise the i2c bus will be hang. This patch is a workaround, it add a void function which is defined as a weak symbol in i2c driver, and it is called before every i2c operation. In mx6slevk, this function was overwrite to execute elan initialization. So that, for mx6slevk board, it will initialize elan before every i2c operation, but for other boards, it just work as before. Signed-off-by: Haibo Chen <haibo.chen@freescale.com> (cherry picked from commit 4c587b29c423ce61b2471ed20f31ff533d9d8a39) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: arch/arm/include/asm/arch-mx6/mx6sl_pins.h board/freescale/mx6slevk/mx6slevk.c
* MLK-10370: imx7d-12x12-arm2 imximage: update dcd table for lpddr3Adrian Alonso2015-04-29-14/+22
| | | | | | | | | | | * Update DCD table for lpddr3 @400Mhz * Boot kernel linux and run memtester for memory stress memtester 1G 100000 Signedoff-by: Ye.Li <B37916@freescale.com> Signed-off-by: Adrian Alonso <aalonso@freescale.com> (cherry picked from commit 7cbab5830d486733a691be104cbc2be494b00776) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10362 imx: mx7dsabresd: Add support for MX7D SABRESD boardPeng Fan2015-04-29-0/+1170
| | | | | | | | | | | | | | | Add i.MX7D SABRESD board BSP codes, with enabled modules: UART, PMIC, USB/OTG, SD, eMMC, ENET, I2C, 74LV IOX. Build target: mx7dsabresd_config Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 3bf52a153e2964d4fdc17f0e8cb816686cbb6c2b) Conflicts: boards.cfg
* MLK-10361 imx: mx7d arm2: Change to use WDOG_B resetYe.Li2015-04-29-2/+12
| | | | | | | | | | | | | | | | | | | | | The default u-boot reset is a internal WDOG reset (warm reset on i.MX6) which does not have power and DDR reset. So the peripherals and DDR may meet problem. When using the internal WDOG reset on i.MX7D ARM2 boards, we meets two DDR issues: 1. On 12x12 ARM2, sometimes the system may hang in DCD because the DDRC Operating Mode does not become to normal. 2. On 19x19 ARM2, the reset always brings system to USB download because the DDR3 turns to unstable. On the i.MX7D ARM2 board, the WDOG_B signal connects to POR_B or PMIC_PWRON. This gives a chance to use a stronger reset. So in this patch, we set the IOMUX for WDOG_B pin and enable WDOG_B signal output in WDOG WCR register. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 1192501c1fcf3b266eb22639a6bc93ac7c03b367) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10351 imx: mx7d: Add 19x19 DDR3L ARM2 board supportYe.Li2015-04-29-0/+1008
| | | | | | | | | | | | | | | Add BSP codes, configuration head file and build target for 19x19 DDR3L ARM2 board with basic functions: ENET2, I2C, SD/eMMC/MMC, USB, QSPI, ECSPI, pfuze3000 PMIC. Build target: mx7d_19x19_ddr3_arm2_config Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 58fd869e3097b7461fbfae3d94e3ebbd30ae2474) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: boards.cfg
* MLK-10191-3 imx: mx7: Add support for i.MX7D 12x12 LPDDR3 ARM2 boardYe.Li2015-04-29-0/+985
| | | | | | | | | | | | | | | | Add BSP codes, configuration head file and build target for 12x12 LPDDR3 ARM2 board with basic functions: ENET, I2C, SD/eMMC/MMC, USB, LCD Splash screen, QSPI, ECSPI, pfuze3000 PMIC. Note: pmic and video is still not upstream way Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit ac0d51ef07fdec880e6da318c08d521506640efa) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: boards.cfg
* MLK-10774-22 imx:mx6sx_arm2 add mx6sx arm2 bspPeng Fan2015-04-29-0/+2919
| | | | | | | Add bsp and configuration file Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-21 imx:imx6sxsabreauto add bspPeng Fan2015-04-29-0/+1142
| | | | | | | Add bsp and configuration file Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-20 imx:mx6 add plugin supportPeng Fan2015-04-29-10/+2548
| | | | | | Add plugin support Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-19 imx:mx6qsabreauto update bspPeng Fan2015-04-29-102/+461
| | | | | | Update bsp and add configuration file Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-18 imx:mx6qarm2 update bspPeng Fan2015-04-29-6/+279
| | | | | | Update bsp and add configuration file Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-17 imx:mx6sabresd update bspPeng Fan2015-04-29-441/+726
| | | | | | Update bsp and add configuration file Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-16 imx:mx6sxsabresd update board and configPeng Fan2015-04-29-49/+461
| | | | | | | | | Update mx6sxsabresd board and config file Note: Fastboot Android support is not added. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-15 imx:mx6slevk update board codePeng Fan2015-04-29-8/+148
| | | | | | | | | | | Update board header and bsp code in board/freescale/mx6slevk Update board config file Note: Fastboot will be added in future Android config is not included. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-5 Add EPDC splash screen for MX 6DL SabreSD and 6SL EVKPeng Fan2015-04-29-0/+657
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add EPDC splash screen feature for MX6SL EVK, and MX6DL SABRESD board. - Currently, splash screen consists of a simple black border around a white screen. Done this way to save in memory footprint. - EPDC splash screen is disabled by default in the config file for MX6DL_SABRESD and MX6SL_EVK. If left enabled, the U-Boot image will not boot correctly (hang), since some additional content on the boot device (waveform file) is required for EPDC splash to work correctly. Please refer to Linux Reference Manual for how to flash WAVEFORM file. Signed-off-by: Robby Cai <R63905@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com> (cherry picked from commit b8ab9b3eabb94bbbc1eea63e7c0e2a87d2d645f4) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Conflicts: arch/arm/include/asm/arch-mx6/mx6sl_pins.h board/freescale/mx6sabresd/mx6sabresd.c board/freescale/mx6slevk/mx6slevk.c drivers/video/Makefile include/configs/mx6sabresd.h include/configs/mx6slevk.h include/lcd.h drivers/video/Makefile
* MLK-10774-2 HDMI: splash screen function enhancementPeng Fan2015-04-29-10/+10
| | | | | | | | | | | | | | -Change HDMI video mode to VGA. -Add pixel clock fraction part setting in IPU driver, fix video mode timing issue. -Add overflow state clear workaround, fix kernel hang in HDMI driver issue. -Correct IPU clock to 264MHz. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com> (cherry picked from commit 45d532a0237f5baf2ec95b4364ec5bc94d312689) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2015-04-13-1/+0
|\
| * mx53loco: Disable printing cpuinfoFabio Estevam2015-04-08-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 32df39c741788e ("mx5: fix get_reset_cause") we have the following boot messages on a mx53qsb: U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39) CPU: Freescale i.MX53 rev2.1 at 800 MHz Reset cause: POR Board: MX53 LOCO I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial CPU: Freescale i.MX53 rev2.1 at 1000 MHz Reset cause: unknown reset Net: FEC [PRIME] The CPU and Reset cause lines appear twice. Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via I2C to raise the CPU voltage so that it can run at 1GHz. To avoid such misleading double printings, disable printing cpu info for now. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
* | m68k: fix 3 broken boardsangelo@sysam.it2015-03-28-2/+0
|/ | | | | | | | | | | Fix eb_cpu5282 and eb_cpu5282_internal unresolved external error. These boards have video but don't need any ppc related video_setmem(). Fix M53017EVB moving away embedded env to a different offset, as in M52277EVB. Signed-off-by: Angelo Dureghello <angelo@sysam.it>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2015-03-05-44/+880
|\
| * SECURE_BOOT : enable esbc_validate command for powerpc and arm platforms.gaurav rana2015-03-05-0/+6
| | | | | | | | | | | | | | | | | | | | esbc_validate command uses various IP Blocks: Security Monitor, CAAM block and SFP registers. Hence the respective CONFIG's are enabled. Apart from these CONFIG_SHA_PROG_HW_ACCEL and CONFIG_RSA are also enabled. Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * SECURE BOOT: Add command for validation of imagesgaurav rana2015-03-05-0/+874
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. esbc_validate command is meant for validating header and signature of images (Boot Script and ESBC uboot client). SHA-256 and RSA operations are performed using SEC block in HW. This command works on both PBL based and Non PBL based Freescale platforms. Command usage: esbc_validate img_hdr_addr [pub_key_hash] 2. ESBC uboot client can be linux. Additionally, rootfs and device tree blob can also be signed. 3. In the event of header or signature failure in validation, ITS and ITF bits determine further course of action. 4. In case of soft failure, appropriate error is dumped on console. 5. In case of hard failure, SoC is issued RESET REQUEST after dumping error on the console. 6. KEY REVOCATION Feature: QorIQ platforms like B4/T4 have support of srk key table and key revocation in ISBC code in Silicon. The srk key table allows the user to have a key table with multiple keys and revoke any key in case of particular key gets compromised. In case the ISBC code uses the key revocation and srk key table to verify the u-boot code, the subsequent chain of trust should also use the same. 6. ISBC KEY EXTENSION Feature: This feature allows large number of keys to be used for esbc validation of images. A set of public keys is being signed and validated by ISBC which can be further used for esbc validation of images. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * mpc85xx/t104xrdb : remove raw timing parametervijay rai2015-03-05-44/+0
| | | | | | | | | | | | | | | | This board uses DDR DIMM. Reading SPD provides more flexibility. Raw timing parameter code should be removed after debugging. Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2015-03-05-21/+105
|\ \ | |/ |/|
| * mx5: fix get_reset_causeStefano Babic2015-03-05-16/+0
| | | | | | | | | | | | | | | | | | | | | | | | commit d9f43c8f5c1d7ed27c99a06be85a4bb64b2c73fb sets get_reset_cause() as static, but this conflicts with mx5 where its prototype is in sys_proto.h. Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco, factorizing the call for this board. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org>
| * mx6slevk: Provide a proper pad configuration for OTG1_ID pinFabio Estevam2015-03-02-1/+6
| | | | | | | | | | | | | | Pass the same pad configuration as done in the kernel so that OTG1_ID pin can properly work in device mode. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mx25pdk: Turn on the LCD supplyFabio Estevam2015-03-02-2/+2
| | | | | | | | | | | | | | | | | | Currently there is no support for MC34704 PMIC in the mainline kernel. Turn on the LCD supply via bootloader for the time being, so that we could use the LCD in the kernel. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * Merge branch 'master' of git://git.denx.de/u-bootStefano Babic2015-03-02-4/+83
| |\
| * | imx:mx6slevk implement power init boardPeng Fan2015-02-23-0/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement power_init_board and related I2C interface configuration. After adding this, uboot can successfully detect and configure pmic. " U-Boot 2015.01-00281-ge29eddf (Feb 12 2015 - 09:24:01) CPU: Freescale i.MX6SL rev1.0 at 396 MHz Reset cause: POR Board: MX6SLEVK I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 " Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
| * | Merge branch 'master' of git://git.denx.de/u-bootStefano Babic2015-02-13-3413/+525
| |\ \
| * | | imx:mx6 set normal APS and standby PFM modePeng Fan2015-02-11-2/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To normal mode, use APS switching mode. To standy mode, use PFM switching mode. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
| * | | pmic:pfuze implement pmic_mode_initPeng Fan2015-02-11-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is to implement pmic_mode_init function, and add prototype in header file. This function is to set switching mode for pmic buck regulators to improve system efficiency. Mode: OFF: The regulator is switched off and the output voltage is discharged. PFM: In this mode, the regulator is always in PFM mode, which is useful at light loads for optimized efficiency. PWM: In this mode, the regulator is always in PWM mode operation regardless of load conditions. APS: In this mode, the regulator moves automatically between pulse skipping mode and PWM mode depending on load conditions. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
* | | | mpc837xerdb: "fix Calling __hwconfig without a buffer" warningSinan Akman2015-03-02-1/+6
| |_|/ |/| | | | | | | | Signed-off-by: Sinan Akman <sinan@writeme.com>
* | | arm: ls1021x: Add support for initializing CAAM's stream idAlison Wang2015-02-24-0/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | There 4 JRs, 4 RTICs and 8 DECOs, and set them the same stream id for using the same SMMU3 on LS1021A. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | | drivers/mc: Migrated MC Flibs to 0.5.2J. German Rivera2015-02-24-2/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree from "fsl,dprcr" to "fsl-mc". Print MC version info when appropriate. Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | | ARMv8/LS2085A: Enable auto precharge for DP-DDRYork Sun2015-02-24-0/+1
| | | | | | | | | | | | | | | | | | | | | DP-DDR benefits from auto precharge because of its specific application. Signed-off-by: York Sun <yorksun@freescale.com>
* | | armv8/ls2085a: Enable cluster timebase for all clustersYork Sun2015-02-24-2/+9
| |/ |/| | | | | | | | | | | LS2085A and its variants can have up to four clusters. It is safe to enable timebase for all even some may be disabled. Signed-off-by: York Sun <yorksun@freescale.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2015-02-10-28/+172
|\ \ | |/
| * mx53loco: Fix boot hang during reboot stress testFabio Estevam2015-02-10-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently by running the following test: => setenv bootcmd reset => save => reset , we observe a hang after approximately 20-30 minutes of stress reboot test. Investigation of this issue revealed that when a single DDR chip select is used, the hang does not happen. It only happens when the two chip selects are active. MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence": "The controller must keep the memory lines quiet (except for CK) for the ZQ calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256 for other ZQCL and 64 for ZQCS)." According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL: "Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines. Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)" So make sure to activate one chip select at time (CS0 first and then CS1 later), so that the required JEDEC delay is respected for each chip select. With this change applied the board has gone through three days of reboot stress test without any hang. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * imx: mx6qsabreauto: Change to use common GPMI IO clock functionYe.Li2015-02-10-23/+2
| | | | | | | | | | | | | | | | Since a clock function setup_gpmi_io_clk is implemented for GPMI IO clock settings, change to use this common function in GPMI setup. Signed-off-by: Ye.Li <B37916@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
generated by cgit v1.1 at 2024-09-30 10:25:56 +0000