summaryrefslogtreecommitdiff
path: root/board/freescale
Commit message (Collapse)AuthorAgeLines
* rename _end to __bss_end__Po-Yu Chuang2011-03-27-23/+23
| | | | | | | Currently, _end is used for end of BSS section. We want _end to mean end of u-boot image, so we rename _end to __bss_end__ first. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
* powerpc/corenet_ds: revise platform dependent parametersYork Sun2011-03-05-4/+4
| | | | | | | | This patch revised clk_adjust and wrlvl_start timings for corenet_ds, based on testing on Virtium VL33B5163F-K9S and Kingston KVR1333D3Q8R9S/4G. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* corenet_ds: pick the middle value for all tested timing parametersYork Sun2011-03-05-40/+18
| | | | | | | | | | | For DDR3 controller, the clk_adjust and wrlvl_start are platform-dependent. The best values should be picked up from the middle of all working combinations. This patch updates the table with confirmed values tested on Hynix dual-rank UDIMMs (HMT125U7BFR8C-H9) at 1300MT/s, 1200MT/s, 1000MT/s, 900MT/s, 800MT/s and Kingston quad-rank RDIMMs (KVR1333D3Q8R9S/4G) at 1300MT/s, 1200MT/s, 1000MT/s. Signed-off-by: York Sun <yorksun@freescale.com>
* mx31pdk: Make the full boot log visibleFabio Estevam2011-02-21-1/+6
| | | | | | Use board_early_init_f so that the full boot log output can be displayed. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx31pdk: Use the new relocation schemeFabio Estevam2011-02-21-2/+8
| | | | Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* fsl: update CRC after setting EEPROM identifierTimur Tabi2011-02-09-0/+1
| | | | | | | | | | The "mac id" command is used to initialize the EEPROM data to a specific format, but it was not updating the CRC. This didn't cause any real problems, because writing the data to the EEPROM will always update the CRC anyway, but it did result in a bogus CRC warning. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Add support for Freescale's mx35pdk board.Stefano Babic2011-02-02-0/+810
| | | | | | | | | | | | | | | | | The patch adds suupport for the Freescale's mx35pdk board (known as well as mx35_3stack). The board boots from the NOR flash. Following devices are supported: - two ethernet devices (FEC and SMC911x on debug board) - I2C - PMIC (MC13892) via I2C interface - UART - NOR flash (64MB) - NAND flash (2GB) - basic access to mc9sdz60 registers via I2C interface Signed-off-by: Stefano Babic <sbabic@denx.de>
* MX51EVK: Use SWx macros in PMIC initMarek Vasut2011-02-02-3/+3
| | | | Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
* MX5:MX53: add initial support for MX53EVK boardLiu Hui-R643432011-02-02-0/+581
| | | | | | | Add initial support for MX53EVK board support. FEC, SD/MMC, UART, I2C, have been supported. Signed-off-by: Jason Liu <r64343@freescale.com>
* MX51EVK: UART does not print out the early informationLiu Hui-R643432011-02-02-3/+8
| | | | | | | | | | | | | | The early bootup information is not print out due to the UART pin iomux not set up correctly before board_init Add the board_early_init_f function and enable the CONFIG_BOARD_EARLY_INIT_F. Move the UART pin setting from board_init to board_early_init_f function. This patch also move the FEC pin iomux setup to the board_early_init_f. Signed-off-by: Jason Liu <r64343@freescale.com>
* ppc/85xx: Fix compile err when PCI disabled on P1_P2_RDBPrabhakar Kushwaha2011-01-19-2/+6
| | | | | | | | | u-boot cannot be compiled after disabling CONFIG_PCI. Place PCI related codes under #ifdef CONFIG_PCI Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* corenet_ds: Extend board specific parametersYork Sun2011-01-19-78/+81
| | | | | | | | | Extend board specific parameters to include cpo, write leveling override Extend write leveling sample to 0xf Adding rcw overrid for quad-rank RDIMMs Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Move RESET_VECTOR_ADDRESS into config.hKumar Gala2011-01-19-92/+3
| | | | | | | | | | | Rather than defining it config.mk we can set it in config.h and remove config.mk from several boards that don't need it. We mimic what 4xx does and introduce CONFIG_RESET_VECTOR_ADDRESS for config.h to set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de>
* powerpc/8xxx: Move fsl_is_spd() into generic 8xxx ddr codeKumar Gala2011-01-14-16/+2
| | | | | | | | Move the parsing of hwconfig to determine if to use spd into common code so we can share it across all boards instead of duplicating it everywhere. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Convert MPC8641HPCN to use common SRIO init codeKumar Gala2011-01-14-4/+1
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Convert MPC8569MDS to use common SRIO init codeKumar Gala2011-01-14-2/+1
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Convert MPC8568MDS to use common SRIO init codeKumar Gala2011-01-14-2/+1
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Convert MPC8548CDS to use common SRIO init codeKumar Gala2011-01-14-9/+5
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Refactor SRIO initialization into common codeKumar Gala2011-01-14-44/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Moved the SRIO init out of corenet_ds and into common code for 8xxx/QorIQ processors that have SRIO. We mimic what we do with PCIe controllers for SRIO. We utilize the fact that SRIO is over serdes to determine if its configured or not and thus can setup the LAWs needed for it dynamically. We additionally update the device tree (to remove the SRIO nodes) if the board doesn't have SRIO enabled. Introduced the following standard defines for board config.h: CONFIG_SYS_SRIO - Chip has SRIO or not CONFIG_SRIO1 - Board has SRIO 1 port available CONFIG_SRIO2 - Board has SRIO 2 port available (where 'n' is the port #) CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup) CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup) [ These mimic what we have for PCI and PCIe controllers ] Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de>
* powerpc/85xx: Rework corenet_ds pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-116/+2
| | | | | | | Remove duplicated code in corenet_ds boards and utilize the common fsl_pcie_init_board(). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Rework MPC8610HPCD pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-64/+16
| | | | | | | | Remove duplicated code in MPC8610HPCD board and utilize the common fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Rework P1_P2_RDB pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-62/+2
| | | | | | | | Remove duplicated code in P1_P2_RDB boards and utilize the common fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Rework MPC8569MDS pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-41/+2
| | | | | | | | Remove duplicated code in MPC8569MDS board and utilize the common fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Rework MPC8568MDS pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-39/+14
| | | | | | | | Remove duplicated code in MPC8568MDS board and utilize the common fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Rework MPC8548CDS pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-41/+12
| | | | | | | | Remove duplicated code in MPC8548CDS board and utilize the common fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Rework MPC8641HPCN pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-53/+2
| | | | | | | | Remove duplicated code in MPC8641HPCN board and utilize the common fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Rework MPC8536DS pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-102/+14
| | | | | | | Remove duplicated code in MPC8536DS board and utilize the common fsl_pcie_init_board(). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Rework MPC8544DS pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-83/+26
| | | | | | | | | | | | Remove duplicated code in MPC8544DS board and utilize the common fsl_pcie_init_ctrl(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. We don't use the full fsl_pcie_init_ctrl() since we have to handle PCIE3 specially to setup the additional memory map region and we utilize a single LAW to cover the controller. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Rework P2020DS pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-111/+2
| | | | | | | | | Remove duplicated code in P2020DS board and utilize the common fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Rework MPC8572DS pci_init_board to use common FSL PCIe codeKumar Gala2011-01-14-89/+10
| | | | | | | | | Remove duplicated code in MPC8572DS board and utilize the common fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. Signed-off-by: Chenhui Zhao <b26998@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/fsl-pci: Add generic code to setup PCIe controllersKumar Gala2011-01-14-65/+2
| | | | | | | | | | | | | | | | | | Since all the PCIe controllers are connected over SERDES on the SoCs we can utilize is_serdes_configured() to determine if a controller is enabled. After which we can setup the ATMUs and LAWs for the controller in a common fashion and allow board code to specify what the controller is connected to for reporting reasons. We also provide a per controller (rather than all) for some systems that may have special requirements. Finally, we refactor the code used by the P1022DS to utilize the new generic code. Based on patch by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* MPC8xxx DDR: align informational printsBecky Bruce2011-01-14-16/+18
| | | | | | | | | | | | | | | | | | | | Add spaces to cause the informational prints to line up with the ones from init_func_ram() in board.c. Output now looks like this: .... DRAM: Detected 4096 MB of memory This U-Boot only supports < 4G of DDR You could rebuild it with CONFIG_PHYS_64BIT DDR: 2 GiB (DDR2, 64-bit, CL=5, ECC off) .... The prints from lbc_sdram_init() have also been modified to line line up and changed to start with "LBC SDRAM" instead of the confusing "SDRAM". Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc85xx: rename sdram_init() lbc_sdram_init()Becky Bruce2011-01-14-14/+6
| | | | | | | | sdram_init() is used to initialize sdram on the lbc. Rename it accordingly. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc85xx boards: initdram() cleanup/bugfixBecky Bruce2011-01-14-451/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Correct initdram to use phys_size_t to represent the size of dram; instead of changing this all over the place, and correcting all the other random errors I've noticed, create a common initdram that is used by all non-corenet 85xx parts. Most of the initdram() functions were identical, with 2 common differences: 1) DDR tlbs for the fixed_sdram case were set up in initdram() on some boards, and were part of the tlb_table on others. I have changed them all over to the initdram() method - we shouldn't be accessing dram before this point so they don't need to be done sooner, and this seems cleaner. 2) Parts that require the DDR11 erratum workaround had different implementations - I have adopted the version from the Freescale errata document. It also looks like some of the versions were buggy, and, depending on timing, could have resulted in the DDR controller being disabled. This seems bad. The xpedite boards had a common/fsl_8xxx_ddr.c; with this change only the 517 board uses this so I have moved the ddr code into that board's directory in xpedite517x.c Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Cleanup SGMII detection and reportingKumar Gala2011-01-14-58/+40
| | | | | | | | Use new is_serdes_configured to determine if TSECs are in SGMII mode and report that on the various boards that use or can be configured in SGMII mode in board_eth_init() instead of in the PCI init code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Replace is_fsl_pci_cfg with is_serdes_configuredKumar Gala2011-01-14-28/+28
| | | | | | | Now that we have serdes support for all 85xx/86xx/Pxxx chips we can replace the is_fsl_pci_cfg() code with the is_serdes_configured(). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add support for booting from NAND on MPC8572DSKumar Gala2011-01-14-2/+20
| | | | | | | | Mimic support that exists on MPC8536DS on the MPC8572DS to allow booting from NAND. Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* miiphy: convert to linux/mii.hMike Frysinger2011-01-09-9/+9
| | | | | | | | The include/miiphy.h header duplicates a lot of things from linux/mii.h. So punt all the things that overlap to keep the API simple and to make merging between U-Boot and Linux simpler. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of ../master into nextWolfgang Denk2010-12-16-530/+57
|\
| * p1022ds: fix switching of DIU/LBC signalsTimur Tabi2010-12-13-10/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the P1022, the pins which drive the video display (DIU) are muxed with the local bus controller (LBC), so if the DIU is active, the pins need to be temporarily muxed to LBC whenever accessing NOR flash. The code which handled this transition is checking and changing the wrong bits in PMUXCR. Also add a follow-up read after a write to NOR flash if we're going to mux back to DIU after the write, as described in the P1022 RM. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * video: move fsl_diu_fb driver to drivers/videoAnatolij Gustschin2010-12-01-514/+0
| | | | | | | | | | | | | | | | | | Since the driver is used not only on Freescale boards, we move it to a common place for video drivers as suggested by Wolfgang. The patch also cleans up the top level Makefile. Signed-off-by: Anatolij Gustschin <agust@denx.de>
| * hwconfig: Fix dummy initialization of {board, cpu}_hwconfigKumar Gala2010-11-30-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since board_hwconfig & cpu_hwconfig are defined as weak and dont have a default value they will get put into the BSS if they aren't defined elsewhere. This is problematic as we try to utilize hwconfig before we've relocated and thus BSS isn't setup. Instead of giving dummy values in the board files that utilize this feature, we can just initialize the variables to an empty string and thus move them out of the BSS if they aren't defined elsewhere. Also made board_hwconfig & cpu_hwconfig arrays to reduce size associated with string pointers vs arrays. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | do_reset: unify duplicate prototypesMike Frysinger2010-11-28-4/+0
|/ | | | | | | The duplication of the do_reset prototype has gotten out of hand, and they're not all in sync. Unify them all in command.h. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 74xx_7xx: Cleanup for partial linking and --gc-sectionsWolfgang Denk2010-11-27-133/+0
| | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Stefan Roese <sr@denx.de>
* 512x: Cleanup for partial linking and --gc-sectionsWolfgang Denk2010-11-27-2/+2
| | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Timur Tabi <timur@freescale.com> Acked-by: Stefan Roese <sr@denx.de>
* Switch from archive libraries to partial linkingSebastien Carlier2010-11-17-121/+121
| | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
* mpc85xx: Fix SERDES/eTSEC message indentationPeter Tyser2010-11-14-13/+13
| | | | | | | | | | | | | Previously some mpc85xx boards printed indented messages such as the following on bootup: printf(" eTSEC4 is in sgmii mode.\n"); printf(" Serdes2 disalbed\n"); The bootup appearance looks cleaner if the indentation is removed which aligns these messages with other bootup output. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> CC: galak@kernel.crashing.org
* fsl: Clean up printing of PCI boot infoPeter Tyser2010-11-14-107/+107
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Previously boards used a variety of indentations, newline styles, and colon styles for the PCI information that is printed on bootup. This patch unifies the style to look like: ... NAND: 1024 MiB PCIE1: connected as Root Complex Scanning PCI bus 01 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 03 00 10b5 8112 0604 00 02 01 10b5 8518 0604 00 02 02 10b5 8518 0604 00 08 00 1957 0040 0b20 00 07 00 10b5 8518 0604 00 09 00 10b5 8112 0604 00 07 01 10b5 8518 0604 00 07 02 10b5 8518 0604 00 06 00 10b5 8518 0604 00 02 03 10b5 8518 0604 00 01 00 10b5 8518 0604 00 PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex Scanning PCI bus 0d 0d 00 1957 0040 0b20 00 PCIE2: Bus 0c - 0d In: serial ... Signed-off-by: Peter Tyser <ptyser@xes-inc.com> CC: wd@denx.de CC: sr@denx.de CC: galak@kernel.crashing.org
* powerpc/corenet_ds: display the RCW at bootTimur Tabi2010-11-12-0/+15
| | | | | | | | | | | | | | | Display the 64-byte Reset Configuration Word (RCW) during boot, so that there's no confusion as to what RCW U-boot is using. Reset Configuration Word (RCW): 00000000: 4a500000 00000000 18181818 00008888 00000010: 28402400 00002000 fe800000 01200000 00000020: 00000000 00000000 00000000 000b0000 00000030: 00000000 00000000 00000000 00000000 Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* p1_p2_rdb: to set SQW/INT pin of RTC as INT linePriyanka Jain2010-11-12-1/+3
| | | | | | | | | | SQW/INT pin in RTC can be used for generating square wave(by default) or as interrupt line. U-boot is registering this pin for interrupts. Configuring SQW/INT bit as interrupt line during board initialization to avoid spurious interrupts generated by square wave. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-11-01 05:21:11 +0000