summaryrefslogtreecommitdiff
path: root/board/freescale
Commit message (Collapse)AuthorAgeLines
* Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2014-11-26-9/+36
|\
| * arm: ls102xa: Select ge2_clk125 for eTSEC clock muxingAlison Wang2014-11-24-0/+1
| | | | | | | | | | | | | | | | | | | | EC1 pins in RCW can be selected as RGMII1, GPIO3, CAN1/2, FTM1 or SAI1/2. There is a bug that EC3 RGMII could not work when selecting EC1 as other functionality except RGMII. The workaround is to select ge2_clk125 for eTSEC clock muxing in register SCFG_ETSECCMCR. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Add SystemID EEPROM support for LS1021ATWR boardAlison Wang2014-11-24-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SystemID information could be read through I2C1 from EEPROM on LS1021ATWR board. As LS1 is a little-endian processor, getting the version ID by be32_to_cpu() is wrong. Fix it by using e.version directly. This change will be compatible for both ARM and PowerPC. As there is an errata that I2C1 could not work in SD boot, reading EEPROM through I2C1 is disabled too in SD boot. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Remove bit reversing for SCFG registersAlison Wang2014-11-24-7/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SCFG_SCFGREVCR is SCFG bit reverse register. This register must be written with 0xFFFFFFFF before writing to any other SCFG register. Then other SCFG register could be written in big-endian mode. Address: 157_0000h base + 200h offset = 157_0200h Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 W/R SCFGREV Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0-31 SCFGREV SCFG Bit Reverse Control Filed 32'h 0000_0000 - No bit reverse is applied 32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as 0:31 This patch removes the bit reversing for SCFG registers in u-boot. It will be implemented through PBI commands in RCW .pbi write 0x570200, 0xffffffff .end So other SCFG register could be written in big-endian mode in u-boot or kernel directly. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm: ls102xa: Add snoop disable for slave port 0, 1 and 2Jason Jin2014-11-24-0/+17
| | | | | | | | | | | | | | | | | | Disable the snoop for slave interface 0, 1 and 2 to avoid the interleaving on the CCI400 BUS. Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * qe: add qe support for ls1021a-twr boardZhao Qiang2014-11-19-0/+8
| | | | | | | | | | Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * qe: add qe support to ls1021aqdsZhao Qiang2014-11-19-0/+8
| | | | | | | | | | | | | | add qe support to ls1021aqds Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-11-26-9/+438
|\ \ | | | | | | | | | | | | | | | | | | Conflicts: drivers/mmc/fsl_esdhc.c Signed-off-by: Tom Rini <trini@ti.com>
| * | powerpc/t2080qds: fix for 1000BASE-KXShaohui Xie2014-11-19-0/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1000BASE-KX(1G-KX) uses SGMII protocol but the serdes lane runs in 1G-KX mode. By default, the lane runs in SGMII mode, when a MAC uses a lane in 1G-KX mode, corresponding bit in PCCR1 for the lane needs to be set, and needs to fixup dtb accordingly for kernel to do proper initialization. Hwconfig "fsl_1gkx" is used to indicate a MAC runs in 1G-KX mode, FM1 MAC 1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a MAC runs in 1G-KX mode, set its' corresponding env in "fsl_1gkx", 'fm1_1g1' stands for FM1-MAC1, 'fm1_1g2' stands for FM1-MAC2, etc. If all MAC 1/2/5/6/9/10 run in 1G-KX mode, the hwconfig should has below setting: fsl_1gkx:fm1_1g1,fm1_1g2,fm1_1g5,fm1_1g6,fm1_1g9,fm1_1g10 Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> [York Sun: Fix compiling warning] Reviewed-by: York Sun <yorksun@freescale.com>
| * | powerpc/t2080qds: fixup dtb for 10g-krshaohui xie2014-11-19-11/+98
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | XFI ports on t2080qds can work with fiber cable and direct attach cable(copper). We use hwconfig to define cable type for XFI, and fixup dtb based on the cable type. For copper cable, set below env in hwconfig: fsl_10gkr_copper:<10g_mac_name> the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4. fm1_10g1 stands for FM1-MAC9, fm1_10g2 stands for FM1-MAC10, fm1_10g3 stands for FM1-MAC1, fm1_10g4 stands for FM1-MAC2. The four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports, if a given 10G port will use the copper cable for 10GBASE-KR, set the <10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be assumed to be used for the port. For ex. if four XFI ports will both use copper cable, the hwconfig should contain: fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4 Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * | board/t2080qds: add readme for t2080qdsShengzhou Liu2014-11-19-0/+243
| |/ | | | | | | | | Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | Merge git://git.denx.de/u-boot-fdtTom Rini2014-11-26-92/+179
|\ \
| * | fdt: Try to use fdt_address_cells()/fdt_size_cells()Simon Glass2014-11-21-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | Use these new functions where possible. They default to a value of 2 so we cannot use them in some places where we need a default value of 1. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
| * | fdt: Allow ft_board_setup() to report failureSimon Glass2014-11-21-89/+175
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This function can fail if the device tree runs out of space. Rather than silently booting with an incomplete device tree, allow the failure to be detected. Unfortunately this involves changing a lot of places in the code. I have not changed behvaiour to return an error where one is not currently returned, to avoid unexpected breakage. Eventually it would be nice to allow boards to register functions to be called to update the device tree. This would avoid all the many functions to do this. However it's not clear yet if this should be done using driver model or with a linker list. This work is left for later. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-11-24-192/+345
|\ \
| * | mx53ard: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx53evk: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx53smd: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6qarm2: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx51evk: Fix error handling in board_mmc_init()Fabio Estevam2014-11-21-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | imx: imx6q/dlsabreauto: Add PMIC Pfuze100 supportYe.Li2014-11-20-0/+15
| | | | | | | | | | | | | | | | | | | | | Add the pfuze100 initialization in power_init_board for imx6q/dl sabreauto board. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | imx: mx6sxsabresd: Use the pfuze common init functionYe.Li2014-11-20-41/+7
| | | | | | | | | | | | | | | | | | | | | | | | Modify the pfuze init for mx6sxsabresd to use the shared "pfuze_common_init" function. And move this initialization to power_init_board. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | imx: mx6sabresd: Use the pfuze common init functionYe.Li2014-11-20-43/+9
| | | | | | | | | | | | | | | | | | | | | | | | Modify the pfuze init for mx6sabresd to use the shared "pfuze_common_init" function. And move this initialization to power_init_board. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | imx: mx6sabre common: Factorize the Pfuze init functionYe.Li2014-11-20-0/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | Since the Pfuze initializations are similar on various mx6 SABRE boards. Factorize the initialization to a common function in file board/freescale/common/pfuze.c. So that all SABRE boards BSP can share the function. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | imx: mx6sxsabresd: Add board support for USDHC2 and USDHC3Ye.Li2014-11-20-5/+94
| | | | | | | | | | | | | | | | | | | | | | | | Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board. The default boot socket is USDHC4, so the MMC environment device and mmcdev variable are set to this device. Signed-off-by: Ye.Li <B37916@freescale.com>
| * | mx6sabresd: Access SRC_SBMR1 register via structureFabio Estevam2014-11-20-3/+2
| | | | | | | | | | | | | | | | | | | | | In U-boot it is preferred to access the register via structure pointer, so convert it such style. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6sabresd: Add mx6sabresd_spl_defconfig to MAINTAINERS entryFabio Estevam2014-11-20-0/+1
| | | | | | | | | | | | | | | | | | | | | Let's add mx6sabresd_spl_defconfig entry into MAINTAINERS, so that we avoid getting a warning that the mx6sabresd_spl is not maintained. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6sxsabresd: Simplify the return value of setup_fec()Fabio Estevam2014-11-20-6/+1
| | | | | | | | | | | | | | | | | | | | | We can simply the return the value from enable_fec_anatop_clock() to make the code smaller and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6slevk: Simplify the return value of setup_fec()Fabio Estevam2014-11-20-6/+1
| | | | | | | | | | | | | | | | | | | | | We can simply the return the value from enable_fec_anatop_clock() to make the code smaller and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6sabresd: State that only mx6q is supported in SPLFabio Estevam2014-11-20-4/+2
| | | | | | | | | | | | | | | | | | Make clear that current SPL code only supports the mx6q variant. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx53loco: Fix error handling in board_mmc_init()Fabio Estevam2014-11-20-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6qsabreauto: Add parallel NOR flash supportFabio Estevam2014-11-20-1/+79
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mx6sabreauto boards come with 32 MiB of parallel NOR flash. Add support for it: U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: MX6Q-Sabreauto revA I2C: ready DRAM: 2 GiB Flash: 32 MiB NAND: 0 MiB Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is not used. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6: Use a common SPL configuration fileFabio Estevam2014-11-20-20/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | Many boards use a minimal .cfg file in the SPL case. Introduce spl_sd.cfg so that we can reuse it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | mx6sabresd: Move the DCD settings to spl codeFabio Estevam2014-11-20-38/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR. Move the configuration to the spl code. CCM_CCOSR setting is no longer required to get audio functionality in the kernel, so remove such setting. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | imx:mx6sxsabresd fix pfuz probe failedPeng Fan2014-11-20-1/+4
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The PFUZ probe failed with the following msg: " wait_for_sr_state: failed sr=81 cr=a0 state=2020 i2c_init_transfer: failed for chip 0x8 retry=0 wait_for_sr_state: failed sr=81 cr=a0 state=2020 i2c_init_transfer: failed for chip 0x8 retry=1 wait_for_sr_state: failed sr=81 cr=a0 state=2020 i2c_init_transfer: failed for chip 0x8 retry=2 i2c_init_transfer: give up i2c_regs=021a0000 Can't find PMIC:PFUZE100 " board_early_init_f is too early to call i2c related setting, because init_func_i2c is called after board_early_init_f being invoked. Thus move setup_i2c into board_init. Also PFUZ is connected to I2C bus 0, so change "1" -> "0". Using this patch PFUZ can be correctly probed: "PMIC: PFUZE100 ID=0x11" Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* | linux/kernel.h: sync min, max, min3, max3 macros with LinuxMasahiro Yamada2014-11-23-3/+3
|/ | | | | | | | | | | | | | | | | | | | U-Boot has never cared about the type when we get max/min of two values, but Linux Kernel does. This commit gets min, max, min3, max3 macros synced with the kernel introducing type checks. Many of references of those macros must be fixed to suppress warnings. We have two options: - Use min, max, min3, max3 only when the arguments have the same type (or add casts to the arguments) - Use min_t/max_t instead with the appropriate type for the first argument Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Pavel Machek <pavel@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> [trini: Fixup arch/blackfin/lib/string.c] Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-11-14-0/+239
|\
| * powerpc/BSC9131RDB: Enable creation of dynamic partitions for NANDAshish Kumar2014-11-14-0/+11
| | | | | | | | | | | | | | | | | | | | * fdt_fixup_mtdparts is called from ft_board_setup * Run "mtdparts default" to create NAND partition on uboot * Use mtdparts to create partitions dynamically rather than using static partitions in device tree Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/BSC9132QDS: Enable creation of dynamic partition for NAND and NORAshish Kumar2014-11-14-0/+12
| | | | | | | | | | | | | | | | | | | | * fdt_fixup_mtdparts is called from ft_board_setup * run "mtdparts default" to create NAND, NOR partition on uboot * Use mtdparts to create partitions dynamically rather than using static partitions in device tree Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * t104xrdb: Add Errata A_007662, A_008007 workaround in pbi.cfgPriyanka Jain2014-11-14-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | -A_007662 states that for x1 link width, PCIe2 controller trains in Gen1 speed while configured for Gen2 speed. Workaround:Set the width to x1 and speed to Gen2 by writing to CCSR registers in PBI phase -A_008007 states that PVR register may show random value. Workaround: Reset PVR register using DCSR space in PBI phase Add PBI based software workaround for A_007662 and A_008007 in t104x_pbi.cfg. This is required for SPL-based bootloaders like NAND-boot, SD-boot, SPI-boot Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t4rdb: Add support of CPLDChunhe Lan2014-11-14-0/+206
| | | | | | | | | | | | | | | | | | | | | | This support of CPLD includes - Files and register definitions - Command to switch alternate bank - Command to switch default bank Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | mx6sabresd: Staticize when possibleFabio Estevam2014-11-13-6/+6
| | | | | | | | | | | | Annotate 'static' when appropriate for the variables used locally. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx6sabresd: Fix error handling in board_mmc_init()Fabio Estevam2014-11-13-4/+6
| | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | imx6: SPL support for iMX6 SabreSDJohn Tobias2014-11-13-2/+184
| | | | | | | | | | | | | | | | This patch will enable the support for SPL on iMX6 SabreSD. It tested on SD2 and SD3 mmc port (Switch 1 or 2 of SW6) Signed-off-by: John Tobias <john.tobias.ph@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
* | imx6: add data configuration file for SPLJohn Tobias2014-11-13-0/+58
| | | | | | | | | | | | | | It's a trim version of mx6q_4x_mt41j128.cfg. It just removed the related settings for DDR Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
* | imx: mx6q/dlsabreauto: And NAND flash supportYe.Li2014-11-13-0/+66
| | | | | | | | | | | | | | | | | | | | | | The i.MX6Q/DL sabreauto board has one NAND socket, set the CONFIG_NAND_MXS and relevant NAND configurations to enable the MXS NAND flash driver. Add board level codes to set IOMUX and clock for GPMI-NAND and BCH module. Signed-off-by: Ye.Li <B37916@freescale.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mx53loco: Change 'fdt_file' dynamicallyFabio Estevam2014-11-13-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | Since kernel 3.15 there are two dtb's for the imx53-qsb board: imx53-qsb.dtb - For the boards with DA9053 PMIC imx53-qsrb.dtb - For the boards with MC34708 PMIC Change the 'fdt_file' dynamically, so that the correct dtb can be used depending on the board variant. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
* | mx28evk: README: Revision C is also supportedFabio Estevam2014-11-12-1/+1
|/ | | | | | Adjust the text to mention that rev C of the board is also supported. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-11-05-6/+253
|\
| * imx: mx6 sabreauto: Add board support for USB EHCIYe.Li2014-11-03-0/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On mx6 sabreauto board, there are two USB ports: 0: OTG 1: HOST The EHCI driver is enabled for this board, but the IOMUX and VBUS power control is not implemented, which cause both USB port failed to work. This patch fix the problem by adding the board support codes. Since the power control uses the GPIO pin from port expander MAX7310, the PCA953X driver is enabled for accessing the MAX7310. The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting its daisy chain. Add a new function "imx_iomux_set_gpr_register" to handle GPR register setting. Signed-off-by: Ye.Li <B37916@freescale.com>
generated by cgit v1.1 at 2024-11-05 21:44:02 +0000