summaryrefslogtreecommitdiff
path: root/board/freescale
Commit message (Collapse)AuthorAgeLines
* 86xx: Cleanup MP supportKumar Gala2009-04-01-1/+1
| | | | | | | | | | | | | | * Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx * Introduce determine_mp_bootpg() helper. We'll need this to address a bug introduced in v2009.03 with 86xx MP booting. We have to make sure to reserve the region of memory used for the MP bootpg() so other u-boot code doesn't use it. * Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to allow cmd_mp.c to build and work. In the future we should look at implementing all these functions. This could be common w/85xx if we use spin tables on 86xx. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc8641hpcn/sbc8641d: Add missing board_lmb_reservesBecky Bruce2009-03-31-0/+9
| | | | | | | | | | | | We're missing the board_lmb_reserve definitions that allow cpu_mp_lmb_reserve to be called; this means that Linux is free to reallocate reserved pages. Linux currently boots because we're getting lucky - the page we've reserved is high enough in memory that it isn't allocated by Linux while we still need it to be in existence. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* MPC85xx: Add MPC8569MDS board supportHaiying Wang2009-03-30-0/+934
| | | | | | | | | This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Use common LSDMR defines from asm/fsl_lbc.hKumar Gala2009-03-30-24/+25
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Add wait flags to support board/chip specific delaysWolfgang Grandegger2009-03-23-1/+1
| | | | | | | | | | | | | | The NAND flash on the TQM8548_BE modules requires a short delay after running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE requires a further short delay after writing out a buffer. Normally the R/B pin should be checked, but it's not connected on the TQM8548_BE. The corresponding Linux FSL UPM driver uses similar delay points at the same locations. To manage these extra delays in a more general way, I introduced the "wait_flags" field allowing the board-specific driver to specify various types of extra delay. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* Add multi chip support to the FSL-UPM driverWolfgang Grandegger2009-03-23-1/+1
| | | | | | | | | | | This patch adds support for multi-chip NAND devices to the FSL-UPM driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now called with the argument "chip_nr" to allow testing the proper chip select line. The NAND support of the MPC8360ERDK is updated as well. No other boards are currently using the FSL UPM driver. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* Fix all linker script to handle all rodata sectionsTrent Piepho2009-03-20-62/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A recent gcc added a new unaligned rodata section called '.rodata.str1.1', which needs to be added the the linker script. Instead of just adding this one section, we use a wildcard ".rodata*" to get all rodata linker section gcc has now and might add in the future. However, '*(.rodata*)' by itself will result in sub-optimal section ordering. The sections will be sorted by object file, which causes extra padding between the unaligned rodata.str.1.1 of one object file and the aligned rodata of the next object file. This is easy to fix by using the SORT_BY_ALIGNMENT command. This patch has not be tested one most of the boards modified. Some boards have a linker script that looks something like this: *(.text) . = ALIGN(16); *(.rodata) *(.rodata.str1.4) *(.eh_frame) I change this to: *(.text) . = ALIGN(16); *(.eh_frame) *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) This means the start of rodata will no longer be 16 bytes aligned. However, the boundary between text and rodata/eh_frame is still aligned to 16 bytes, which is what I think the real purpose of the ALIGN call is. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
* ColdFire: Fix M5329EVB and M5373EVB nand issueTsiChung Liew2009-03-17-4/+8
| | | | | | | | The Nand flash was unable to read and write properly due to Nand Chip Select (nCE) setup was in reverse order. Also, increase the Nand time out value to 60. Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
* fsl: Remove unnecessary debug printfsAndy Fleming2009-03-09-3/+0
| | | | | | | These were left in accidentally, and are not really useful unless the code is as broken as it was when it was being developed. Signed-off-by: Andy Fleming <afleming@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2009-03-09-7/+7
|\ | | | | | | | | | | | | Conflicts: lib_ppc/board.c Signed-off-by: Wolfgang Denk <wd@denx.de>
| * mpc83xx: MPC837XEMDS: Initialize SerDes before negating PCIE reset signalAnton Vorontsov2009-03-05-7/+7
| | | | | | | | | | | | | | | | | | | | The SerDes initialization should be finished before negating the reset signal according to the reference manual. This isn't an issue on real hardware, but we'd better stick to the specifications anyway. Suggested-by: Liu Dave <DaveLiu@freescale.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2009-02-24-0/+57
|\ \ | |/
| * mpc83xx: MPC837XERDB: Add PCIe supportAnton Vorontsov2009-02-23-0/+57
| | | | | | | | | | | | | | | | On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe slots. Let's support them. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | mpc8641hpcn: Indicate 36-bit addr map in boot messagesBecky Bruce2009-02-23-0/+3
|/ | | | | | | If 36-bit addressing is enabled, print a message on the console when we boot. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
* 83xx: Add eSDHC support on 8379 EMDS boardAndy Fleming2009-02-16-5/+18
| | | | Signed-off-by: Andy Fleming <afleming@freescale.com>
* 85xx: Add eSDHC support for 8536 DSAndy Fleming2009-02-16-0/+14
| | | | Signed-off-by: Andy Fleming <afleming@freescale.com>
* 86xx: Reset updatePeter Tyser2009-02-16-0/+16
| | | | | | | | | | Update the 86xx reset sequence to try executing a board-specific reset function. If the board-specific reset is not implemented or does not succeed, then assert #HRESET_REQ. Using #HRESET_REQ is a more standard reset procedure than the previous method and allows all board peripherals to be reset if needed. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* 85xx: print boot header info to distinquish 36-bit addr map on MPC8572 DSKumar Gala2009-02-16-2/+6
| | | | | | | | Added some info that is printed out when we boot to distiquish if we built MPC8572DS_config vs MPC8572DS_36BIT_config since they have different address maps. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Fixup SGMII PHY ids in the device treeAndy Fleming2009-02-16-0/+79
| | | | | | | | | | | The device tree's PHY addresses need to be fixed up if we're using the SGMII Riser Card. The 8572, 8536, and 8544 DS boards were modified to call this function. Code idea taken from Liu Yu <yu.liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* 85xx: Fix bug in device tree setup in 36-bit physical confgKumar Gala2009-02-16-1/+2
| | | | | | | | | | In the 36-bit physical config for MPC8572DS when need the start address of memory and it size to be kept in phys_*_t instead of a ulong since we support >4G of memory in the config and ulong cant represent that. Otherwise we end up seeing the memory node in the device tree reporting back we have memory starting @ 0 and of size 0. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Fix address map for 36-bit config of MPC8572DSKumar Gala2009-02-16-2/+4
| | | | | | | | | | When we introduced the 36-bit config of the MPC8572DS board we had the wrong PCI MEM bus address map. Additionally, the change to the address map exposes a small issue in our dummy read on the ULI bus. We need to use the new mapping functions to handle that read properly in the 36-bit config. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc8641hpcn: Clean up PCI mapping conceptsBecky Bruce2009-02-10-5/+5
| | | | | | | | | Clean up PCI mapping concepts in the 8641 config - rename _BASE to _BUS, as it's actually a PCI bus address, separate virtual and physical addresses into _VIRT and _PHYS, and use each appopriately. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
* mpc8641hpcn: Set up outbound pci windows before inboundBecky Bruce2009-02-10-6/+6
| | | | | | | | | | Because the inbound pci windows are mapped generously, set up the more specific outbound windows first. This way, when we search the pci regions for something, we will hit on the more specific region. This can actually be a problem on systems with large amounts of RAM. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
* pci: Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY for clarityKumar Gala2009-02-07-4/+4
| | | | | | | | | | The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and can be confusing when reading the code. Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used for system memory mapping purposes. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc8536ds.c: include sata.h to for needed function prototypesWolfgang Denk2009-01-28-0/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Command usage cleanupPeter Tyser2009-01-28-3/+3
| | | | | | | | Remove command name from all command "usage" fields and update common/command.c to display "name - usage" instead of just "usage". Also remove newlines from command usage fields. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Standardize command usage messages with cmd_usage()Peter Tyser2009-01-28-3/+3
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Clean up diufb command definitionsPeter Tyser2009-01-28-1/+1
| | | | | | | The diufb command usage formatting is non-standard. It was made standard in preparation for larger command usage updates. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* SATA: do not auto-initialize during bootMike Frysinger2009-01-27-3/+3
| | | | | | | | | | | | Rather than have the board code initialize SATA automatically during boot, make the user manually run "sata init". This brings the SATA subsystem in line with common U-Boot policy. Rather than having a dedicated weak function "is_sata_supported", people can override sata_initialize() to do their weird board stuff. Then they can call the actual __sata_initialize(). Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2009-01-24-88/+108
|\
| * 85xx: enable the auto self refresh for wake up ARPDave Liu2009-01-23-0/+6
| | | | | | | | | | | | | | | | The wake up ARP feature need use the memory to process wake up packet, we enable auto self refresh to support it. Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com>
| * fsl-ddr: use the 1T timing as default configurationDave Liu2009-01-23-0/+14
| | | | | | | | | | | | | | | | | | For light loaded system, we use the 1T timing to gain better memory performance, but for some heavily loaded system, you have to add the 2T timing options to board files. Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com>
| * 85xx: Introduce CONFIG_SYS_PCI*_IO_VIRT for FSL boardsKumar Gala2009-01-23-2/+2
| | | | | | | | | | | | | | | | | | Introduce a new define to seperate out the virtual address that PCI IO space is at from the physical address. In most situations these are mapped 1:1. However any code accessing the bus should use VIRT. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Andy Fleming <afleming@freescale.com>
| * 85xx: Introduce CONFIG_SYS_PCI*_MEM_VIRT for FSL boardsKumar Gala2009-01-23-28/+28
| | | | | | | | | | | | | | | | | | Introduce a new define to seperate out the virtual address that PCI memory is at from the physical address. In most situations these are mapped 1:1. However any code accessing the bus should use VIRT. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Andy Fleming <afleming@freescale.com>
| * 85xx: Use CONFIG_SYS_{PCI*,RIO*}_MEM_PHYS for physical address on FSL boardsKumar Gala2009-01-23-9/+9
| | | | | | | | | | | | | | | | Use the _MEM_PHYS defines instead of _MEM_BUS for LAW and real address fields of TLBs. This is what we should have always been using from the start. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Andy Fleming <afleming@freescale.com>
| * 85xx: Convert CONFIG_SYS_PCI*_IO_BASE to _IO_BUS for FSL boardsKumar Gala2009-01-23-15/+15
| | | | | | | | | | | | | | Use CONFIG_SYS_PCI*_IO_BUS for the bus relative address instead of _IO_BASE so we are more explicit. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 85xx: Convert CONFIG_SYS_{PCI*,RIO*}_MEM_BASE to _MEM_BUS for FSL boardsKumar Gala2009-01-23-39/+39
| | | | | | | | | | | | | | | | Use CONFIG_SYS_{PCI,RIO}_MEM_BUS for the bus relative address instead of _MEM_BASE so we are more explicit. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Andy Fleming <afleming@freescale.com>
| * 85xx: separate FLASH BASE virtual from physical addressKumar Gala2009-01-23-6/+6
| | | | | | | | | | | | | | | | | | | | Added a CONFIG_SYS_FLASH_BASE_PHYS for use as the physical address and maintain CONFIG_SYS_FLASH_BASE as the virtual address of the flash. This allows us to deal with 36-bit phys on these boards in the future. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Andy Fleming <afleming@freescale.com>
| * 85xx: separate PIXIS virtual from physical addressKumar Gala2009-01-23-4/+4
| | | | | | | | | | | | | | | | | | | | Added a PIXIS_BASE_PHYS for use as the physical address and maintain PIXIS_BASE as the virtual address of the PIXIS fpga registers. This allows us to deal with 36-bit phys on these boards in the future. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Andy Fleming <afleming@freescale.com>
* | mpc83xx: Add PCI-E support for MPC837XEMDS boardsAnton Vorontsov2009-01-21-5/+96
| | | | | | | | | | | | | | | | | | | | | | MPC837XEMDS boards can support PCI-E via "PCI-E riser card". The card provides two PCI-E (x2) ports. Though, only one port can be used in x2 mode. Two ports can function simultaneously in x1 mode. PCI-E x1/x2 modes can be switched via "pex_x2" environment variable. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | mpc83xx: Add PCI-E support for MPC8315ERDB boardsAnton Vorontsov2009-01-21-0/+52
| | | | | | | | | | | | | | | | MPC8315ERDB boards features PCI-E x1 and Mini PCI-E x1 ports. Let's support them. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | MPC8349EMDS: do not setup unused PCI clock outputs in PCI agent modeIra Snyder2009-01-21-7/+0
|/ | | | | | | | | When running in PCI agent mode, the PCI_CLK_OUT signals are not used, so do not enable them. See the MPC8349EA Reference Manual, Section 4.4.2 "Clocking in PCI Agent Mode". Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2009-01-14-12/+13
|\
| * Some changes of TLB entry setting for MPC8572DSHaiying Wang2009-01-13-4/+3
| | | | | | | | | | | | | | | | | | | | - Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode, all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0 can not access PIXIS_BASE anymore (any access will cause DataTLBError exception) - Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
| * Change PCIE1&2 deciide logic on MPC8544DS board more readableRoy Zang2009-01-13-2/+2
| | | | | | | | | | | | | | | | | | | | The IO port selection for MPC8544DS board: Port cfg_io_ports PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7 PCIE2 0x4, 0x5, 0x6, 0x7 PCIE3 0x6, 0x7 This patch changes the PCIE12 and PCIE2 logic more readable. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
| * PCIE2 and PCIE3 are decided by corresponing bit in devdisr instead of PCIE1 bitRoy Zang2009-01-13-2/+2
| | | | | | | | | | | | | | PCIE2 and PCIE3 should be decided by corresponing bit in devdisr instead of PCIE1 bit. On MPC8572DS board, PCIE refers to PCIE1. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
| * Fix IO port selection issue on MPC8544DS and MPC8572DS boardsRoy Zang2009-01-13-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The IO port selection is not correct on MPC8572DS and MPC8544DS board. This patch fixes this issue. For MPC8572 Port cfg_io_ports PCIE1 0x2, 0x3, 0x7, 0xb, 0xc, 0xf PCIE2 0x3, 0x7 PCIE3 0x7 For MPC8544 Port cfg_io_ports PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7 PCIE2 0x4, 0x5, 0x6, 0x7 PCIE3 0x6, 0x7 Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
* | mpc8610hpcd: Fix PCI mapping conceptsBecky Bruce2009-01-13-8/+8
|/ | | | | | | | | Rename _BASE to _BUS, as it's actually a PCI bus address, separate virtual and physical addresses into _VIRT and _PHYS, and use each appopriately. This makes the code easier to read and understand, and facilitates mapping changes going forward. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
* mpc8xxx: LCRR[CLKDIV] is sometimes five bitsTrent Piepho2008-12-19-6/+6
| | | | | | | | | | | | | | On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits instead of four. In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It should be safe as the fifth bit was defined as reserved and set to 0. Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Jon Loeliger <jdl@freescale.com>
* 85xx: Add PORDEVSR_PCI1 definePeter Tyser2008-12-04-1/+1
| | | | | | | | | Add define used to determine if PCI1 interface is in PCI or PCIX mode. Convert users of the old PORDEVSR_PCI constant to use MPC85xx_PORDEVSR_PCI1 Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Andy Fleming <afleming@freescale.com>