summaryrefslogtreecommitdiff
path: root/board/freescale/t4qds
Commit message (Collapse)AuthorAgeLines
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-130/+8
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/t4qds: Slave module for boot from SRIO and PCIELiu Gang2013-06-20-0/+19
| | | | | | | | | | | | | | | | | | | | | When a T4 board boots from SRIO or PCIE, it needs to finish these processes: 1. Set all the cores in holdoff status. 2. Set the boot location to one PCIE or SRIO interface by RCW. 3. Set a specific TLB entry for the boot process. 4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot. 5. Set a specific TLB entry in order to fetch ucode and ENV from master. 6. Set a LAW entry with the TargetID one of the PCIE ports for ucode and ENV. 7. Slave's u-boot image should be generated specifically by make xxxx_SRIO_PCIE_BOOT_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. For more information about the feature of Boot from SRIO/PCIE, please refer to the document doc/README.srio-pcie-boot-corenet. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4240qds: fix PHY reset timeout issueShengzhou Liu2013-05-24-2/+17
| | | | | | | | | QSGMII card has different PHY address against previous SGMII card. We check the type of card in slots and set correct PHY address to avoid complainning "PHY reset timed out" during u-boot booting up. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4qds: Add SW7[4] in the DIP switch displayYork Sun2013-05-24-2/+3
| | | | | | | SW7[4] is the new bit which controls the mapping of eMMC vs SDHC. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32MStephen George2013-05-24-2/+3
| | | | | | | Debug trace buffers are memory mapped in DCSR space beyond 4M. Signed-off-by: Stephen George <stephen.george@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4qds: use clock measurement for sysclk and ddr clockEd Swarthout2013-05-24-0/+28
| | | | | | | | | | Use QIXIS measurement registers to obtain sysclk and ddr clock. This allows using non-standard clock speeds, set by directly writing to clock chip or store the values in qixis clock data eeprom. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* T4240/ramboot: enable PBL tool for T4240Shaohui Xie2013-05-24-0/+43
| | | | | | | | Added a default RCW(1_28_6_12) and PBI configure file for T4240, so it can use PBL tool to produce the ramboot image. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4240qds: Add VDD overrideYork Sun2013-05-24-2/+37
| | | | | | | | | | | | | | | | | | | | Allow VDD voltage overriding with a command. This is an add-on feasture of VID. To override VDD, use command vdd_override with the value of voltage in mV, for example vdd_override <voltage in mV, eg. 1050> The above example will set the VDD to 1.050 volt. Any wrong value out of range of 0.8188 to 1.2125 volt or invalid string is ignored. In addition to the command, if overriding VDD is needed earlier in booting process, save an variable and reboot: setenv t4240qds_vdd_mv <voltage in mV> saveenv Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4240qds: Add board detail for bdinfo commandYork Sun2013-05-24-0/+100
| | | | | | | | | | Print more detail information including core voltage, RCW source, switch settings, etc. with bdinfo command. Signed-off-by: York Sun <yorksun@freescale.com> CC: Wolfgang Denk <wd@denx.de> CC: Tom Rini <trini@ti.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* T4240/eth: fix SGMII card PHY addressShaohui Xie2013-05-14-4/+133
| | | | | | | | | | | | | QSGMII card assumed to be used by default, but if SGMII card is used, it will use different PHY address, but we don't know which card is used until we access PHY on the card. So we check the card type slot by slot, if we can read a PHY ID by reading a SGMII PHY address on a slot, then the slot must have a SGMII card pluged, we mark all ports on that slot, and fix dts to use the SGMII card PHY address when doing dts fixup for the marked ports. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4qds: Fix disabling remote I2C connectionEd Swarthout2013-05-14-3/+3
| | | | | | | | | Only clear IRE bit in qixis brdcfg5 register and keep other bits unchanged. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* T4240/net: use QSGMII card PHY address by defaultShaohui Xie2013-05-14-56/+67
| | | | | | | | Use QSGMII card PHY address as default SGMII card PHY address, QSGMII card PHY address is variable depends on different slot. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* t4240qds/eth: fixup ethernet for t4240qdsShengzhou Liu2013-05-14-14/+90
| | | | | | | | | | | 1, Implemented board_ft_fman_fixup_port() to fix port for kernel. 2, Implemented fdt_fixup_board_enet() to fix node status of different slots and interfaces. 3, Adding detection of slot present for XGMII interface. 4, There is no PHY for XFI, so removed related phy address settings. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4240qds: Add voltage ID supportYork Sun2013-05-14-0/+229
| | | | | | | | T4240 has voltage ID fuse. Read the fuse and configure the voltage correctly. Core voltage has higher tolerance on over side than below. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4240qds: Update DDR timing tableYork Sun2013-05-14-22/+34
| | | | | | | | | | Update the timing table to support more rank density, based on the theory that similar density DIMMs have similar clock adjust and write level start timing. Update the timing for 1600 and 1866 MT/s. Tested with Micron MT18JSF1G72AZ-1G9E1 DIMMs, iDIMM M3CN-4GMJ3C0C-M92. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* T4/serdes: fix the serdes clock frequencyRoy Zang2013-05-14-2/+2
| | | | | | | | | | Reverse the bit sequence to set and display serdes clock frequency correctly. The correct bit maps in BRDCFG2 are 0 1 2 3 4 5 6 7 S1RATE[1:0] S2RATE[1:0] S3RATE[1:0] S4RATE[1:0] Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* ppc: Move lbc_clk and cpu to arch_global_dataSimon Glass2013-02-04-1/+1
| | | | | | | | Move these fields into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Update for bsc9132qds.c, b4860qds.c] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/t4240qds: Print FPGA detail versionPrabhakar Kushwaha2013-01-30-2/+9
| | | | | | | | | | | Qixis FPGA has tag data contains image name and build date. It is helpful to identify the FPGA image precisely. Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4240qds: Add support to dump switch settings on t4240qds boardShaveta Leekha2013-01-30-0/+60
| | | | | | | | | | This function is called by "qixis_reset switch" command and switch settings are calculated from qixis FPGA registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* board/T4240qds:Fix TLB and LAW size of NAND flashPrabhakar Kushwaha2013-01-30-2/+2
| | | | | | | | | | The internal SRAM of Freescale's IFC NAND machine is of 64K and controller's Address Mask Registers is initialised with the same. So Update TLB and LAW size of NAND flash accordingly. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4qds: move VSC3316 config data from t4qds.h to t4qds.cTimur Tabi2013-01-30-11/+12
| | | | | | | | | | Static variables should be defined in C files, not header files, because otherwise every C file that #includes the header file will generate a duplicate of the variables. Since the vsc3316_xxx[] arrays are only used by t4qds.c anyway, just put the variables there. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4qds: Add T4QDS boardYork Sun2012-10-22-0/+1445
The T4240QDS is a high-performance computing evaluation, development and test platform supporting the T4240 QorIQ Power Architecture™ processor. SERDES Connections 32 lanes grouped into four 8-lane banks Two “front side” banks dedicated to Ethernet Two “back side” banks dedicated to other protocols DDR Controllers Three independant 64-bit DDR3 controllers Supports rates up to 2133 MHz data-rate Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller QIXIS System Logic FPGA Each DDR controller has two DIMM slots. The first slot of each controller has up to 4 chip selects to support single-, dual- and quad-rank DIMMs. The second slot has only 2 chip selects to support single- and dual-rank DIMMs. At any given time, up to total 4 chip selects can be used. Detail information can be found in doc/README.t4qds Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit v1.1 at 2024-11-01 03:32:15 +0000