summaryrefslogtreecommitdiff
path: root/board/freescale/t208xrdb
Commit message (Collapse)AuthorAgeLines
* t2080rdb/rcw: update ddr frequency from 1600MT/s to 1867MT/sShengzhou Liu2015-05-04-1/+4
| | | | | | | | | T2080RDB RevC uses new SODIMM 1867MT/s instead of previous 1600MT/s. So update RCW to support new DDR frequency 1867MT/s by default. Reserve the old 1600MT/s in comment for users in needed. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t2080rdb: reset cs4315 phyShengzhou Liu2015-05-04-0/+10
| | | | | | | | CS4315 PHY doesn't support phy-reset by software, it needs to reset it by hardware via CPLD control. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t2080rdb: update ddr to support 1866MT/sShengzhou Liu2015-04-20-2/+2
| | | | | | | | Support SODIMM D3XP12081XL10AA 1866MT/s on T2080RDB. Enable CONFIG_CMD_MEMTEST as well. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t208xrdb: VID supportYing Zhang2015-04-20-0/+7
| | | | | | | | | | | | The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t2080: updating rcw for silicon v1.1Shengzhou Liu2014-12-05-6/+14
| | | | | | | | | T2080 v1.1 requires different MEM_PLL_RAT from previous v1.0, and also update core frequency to 1.8GHz for v1.1. We reserve the support for T2080 v1.0 and enable v1.1 by default. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* fdt: Allow ft_board_setup() to report failureSimon Glass2014-11-21-1/+3
| | | | | | | | | | | | | | | | | | This function can fail if the device tree runs out of space. Rather than silently booting with an incomplete device tree, allow the failure to be detected. Unfortunately this involves changing a lot of places in the code. I have not changed behvaiour to return an error where one is not currently returned, to avoid unexpected breakage. Eventually it would be nice to allow boards to register functions to be called to update the device tree. This would avoid all the many functions to do this. However it's not clear yet if this should be done using driver model or with a linker list. This work is left for later. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
* MAINTAINERS: comment out blank M: fieldMasahiro Yamada2014-09-24-1/+1
| | | | | | | | | | | | | | | | | | Since commit ddaf5c8f3030050fcd356a1e49e3ee8f8f52c6d4 (patman: RunPipe() should not pipe stdout/stderr unless asked), Patman spits lots of "Invalid MAINTAINERS address: '-'" error messages for patches with global changes. It takes too long for Patman to process them. Anyway, "M: -" does not carry any important information. Rather, it is just like a place holder in case of assigning a new board maintainer. Let's comment out. This commit can be reproduced by the following command: find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-13-3/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Add board MAINTAINERS filesMasahiro Yamada2014-07-30-0/+15
| | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-30-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* powerpc/mpc85xx: Check return value of find_tlb_idxYork Sun2014-07-22-4/+9
| | | | | | | | | | find_tlb_idx() is called in board_early_init_r() on multiple boards. The return value is not checked before being used to disable a TLB. In normal case the return value wouldn't be -1. In case of a mis- configuration during porting to a new board, checking the return value may be helpful to reveal some user errors. Signed-off-by: York Sun <yorksun@freescale.com>
* board/t208x: update t2080qds/t2080rdb for errata A-007186Shengzhou Liu2014-06-05-1/+1
| | | | | | | | | | | | | As errata A-007186, we need to use the alternate serdes protocol instead of those impacted protocols. - add support for serdes protocols: 0x1b, 0x50, 0x5e, 0x64, 0x6a, 0xd2, 0x67, 0x70. - update t2080_rcw.cfg to adapt to new rcw_66_15 for t2080qds and t2080rdb. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t2080rdb: some update for t2080rdbShengzhou Liu2014-04-22-6/+6
| | | | | | | | | | | | - update readme. - add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315 ucode from NOR/NAND/SPI/SD/REMOTE. - update cpld vbank with SW3[5:7]=000 as default vbank0 instead of previous SW3[5:7]=111 as default vbank. - fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t208xrdb: Add support of 2-stage NAND/SPI/SD bootShengzhou Liu2014-04-22-16/+188
| | | | | | | | | | | Add support of 2-stage NAND/SPI/SD boot loader using SPL framework. PBL initializes the internal CPC-SRAM and copy SPL(160K) to it, SPL further initializes DDR using SPD and environment and copy u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control to u-boot. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t2080rdb: Add T2080PCIe-RDB board supportShengzhou Liu2014-03-07-0/+993
T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC. It works in two mode: standalone mode and PCIe endpoint mode. T2080PCIe-RDB Feature Overview ------------------------------ Processor: - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz DDR Memory: - Single memory controller capable of supporting DDR3 and DDR3-LP devices - 72bit 4GB DDR3-LP SODIMM in slot Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - Two 10Gbps SFP+ ports on-board - Two 10Gbps Base-T ports on-board Accelerator: - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC SerDes 16 lanes configuration: - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10) - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2) - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3) - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2) - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2) - SerDes-2 Lane G-H: to SATA1 & SATA2 IFC/Local Bus: - NOR: 128MB 16-bit NOR flash - NAND: 512MB 8-bit NAND flash - CPLD: for system controlling with programable header on-board eSPI: - 64MB N25Q512 SPI flash USB: - Two USB2.0 ports with internal PHY (both Type-A) PCIe: - One PCIe x4 gold-finger - One PCIe x4 connector - One PCIe x2 end-point device (C293 Crypto co-processor) SATA: - Two SATA 2.0 ports on-board SDHC: - support a TF-card on-board I2C: - Four I2C controllers. UART: - Dual 4-pins UART serial ports Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
generated by cgit v1.1 at 2024-11-06 01:44:05 +0000