summaryrefslogtreecommitdiff
path: root/board/freescale/p1010rdb
Commit message (Collapse)AuthorAgeLines
* p1010rdb: fix ddr values for p1014rdb (setting bus width to 16bit)Matthew McClintock2012-08-23-3/+4
| | | | | | | | | | | There was an extra 0 in front of the value we were using to mask, remove it to improve the code. Also fix the value written to ddr_sdram_cfg to set the bus width properly to 16 bits Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Minor Coding Style Cleanup.Wolfgang Denk2012-07-22-3/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Minor Coding Style cleanupWolfgang Denk2012-07-10-1/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()York Sun2012-07-06-5/+5
| | | | | | | | We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER(). This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with encryption. Remove all _E entries from SVR list and CPU list. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/p1010rdb: add readme document for p1010rdbShengzhou Liu2012-07-06-0/+212
| | | | Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
* powerpc/p1010rdb: update mux config of p1010rdb boardShengzhou Liu2012-07-06-12/+44
| | | | | | | | | On p1010rdb some signals are muxed for tdm/can/uart/flash. If we don't set fsl_p1010mux:tdm_can to "can" or "tdm" explicitly, defaultly we keep spi chip selection to spi-flash instead of to tdm/slic and disable uart1 when not using flexcan, as well disable sdhc. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
* powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during bootTimur Tabi2012-04-24-5/+1
| | | | | | | | | | | | | | | | Most 85xx boards can be built as a 32-bit or a 36-bit. Current code sometimes displays which of these is actually built, but it's inconsistent. This is especially problematic since the "default" build for a given 85xx board can be either one, so if you don't see a message, you can't always know which size is being used. Not only that, but each board includes code that displays the message, so there is duplication. The 'bdinfo' command has been updated to display this information, so we don't need to display it at boot time. The board-specific code is deleted. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boardsYork Sun2012-04-24-3/+3
| | | | | | | | | P1010RDB and p1_pc_rdb_pc has incorrect configuration for CONFIG_DDR_RAW_TIMING. It should be CONFIG_SYS_DDR_RAW_TIMING. Incorrect setting causes DDR failure in case of SPD absent. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: Make inclusion of USB device fixup conditionalRamneek Mehresh2011-11-08-0/+2
| | | | | | | | Include call to usb device-fixup only when CONFIG_HAS_FSL_DR_USB is defined for the platform - P1020RDB, P1010RDB, P1020-PC Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* punt unused clean/distclean targetsMike Frysinger2011-10-15-6/+0
| | | | | | | | | | The top level Makefile does not do any recursion into subdirs when cleaning, so these clean/distclean targets in random arch/board dirs never get used. Punt them all. MAKEALL didn't report any errors related to this that I could see. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* powerpc/85xx: Add basic support for P1010RDBPoonam Aggrwal2011-09-29-0/+765
Boot methods supported: NOR Flash, SPI Flash and SDCARD This patch adds the following basic interfaces: DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash. P1010RDB Overview ----------------- 1Gbyte DDR3 (on board DDR) Local Bus (IFC): 32Mbyte 16bit NOR flash 32Mbyte SLC NAND Flash 64KB CPLD device(GPCM interface) SPI Flash: 128 Mbit SPI Flash memory SD/MMC: connector to interface with the SD memory card SATA: 1 internal SATA connect to 2.5. 160G SATA2 HDD 1 eSATA connector to rear panel USB 2.0: x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface. x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet eTSEC: eTSEC1: Connected to RGMII PHY VSC8641XKO eTSEC2: Connected to SGMII PHY VSC8221 eTSEC3: Connected to SGMII PHY VSC8221 eCAN: Two DB-9 female connectors for Field bus interface UART: supports two UARTs up to 115200 bps for console TDM: 2 FXS ports connected via an external SLIC to the TDM interface. SLIC: SPI SLIC I2C: Serial EEprom Real time clock 256 Kbit M24256 I2C EEPROM PCIe: PCIe and mPCIe connectors. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-11-05 10:34:59 +0000