| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
|
|
| |
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
| |
|
|
|
|
|
|
| |
Change flexcan compatible string from "fsl,flexcan-v1.0"
to "fsl,p1010-flexcan" to match the device tree.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| |
|
|
|
|
|
|
| |
Move these fields into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for bsc9132qds.c, b4860qds.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
| |
|
|
|
|
|
|
| |
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.
Signed-off-by: York Sun <yorksun@freescale.com>
|
| |
|
|
|
|
|
|
|
| |
On p1010rdb some signals are muxed for tdm/can/uart/flash.
If we don't set fsl_p1010mux:tdm_can to "can" or "tdm" explicitly,
defaultly we keep spi chip selection to spi-flash instead of to
tdm/slic and disable uart1 when not using flexcan, as well disable sdhc.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Most 85xx boards can be built as a 32-bit or a 36-bit. Current code sometimes
displays which of these is actually built, but it's inconsistent. This is
especially problematic since the "default" build for a given 85xx board can
be either one, so if you don't see a message, you can't always know which
size is being used. Not only that, but each board includes code that displays
the message, so there is duplication.
The 'bdinfo' command has been updated to display this information, so
we don't need to display it at boot time. The board-specific code is
deleted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
| |
|
|
|
|
|
|
| |
Include call to usb device-fixup only when CONFIG_HAS_FSL_DR_USB is
defined for the platform - P1020RDB, P1010RDB, P1020-PC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
64KB CPLD device(GPCM interface)
SPI Flash:
128 Mbit SPI Flash memory
SD/MMC:
connector to interface with the SD memory card
SATA:
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0:
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
Two DB-9 female connectors for Field bus interface
UART:
supports two UARTs up to 115200 bps for console
TDM:
2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
SPI SLIC
I2C:
Serial EEprom
Real time clock
256 Kbit M24256 I2C EEPROM
PCIe:
PCIe and mPCIe connectors.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
