| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
|
|
|
| |
ret should not use unsigned integer. Should use signed interger to
compare against 0.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
1. Replace the UDC driver with community's USB gadget d_dnl driver.
2. Integrate the FSL SD/SATA/NAND flash operations, since the GPT and
EFI partitions are not support by i.MX.
3. Add FDT support to community's android image.
4. Change the booti command to boota, due to the booti has been used for
ARM64 image boot.
5. Modify boota implementation to load ramdisk and fdt to their loading
addresses specified in boot.img header, while bootm won't do it for
android image.
6. Modify the android image HAB implementation. Authenticate the boot.img
on the "load_addr" for both SD and NAND.
7. Enable new configuration CONFIG_FSL_FASTBOOT for Freescale's fastboot
with relevant header file "fsl_fastboot.h". While disabling the
configuration, the community fastboot is used.
8. Use community's way to combine cmdline in boot.img and u-boot environment,
not overwrite the cmdline in boot.img
Signed-off-by: Ye.Li <B37916@freescale.com>
|
| |
|
|
|
|
|
|
|
|
| |
Set the ID pin pad to pull up not the pull down at default, otherwise
we can't enter the device mode, but always detect as host.
After this change we have to use portA cable to play as host,
and use portB cable for device.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
| |
|
|
|
|
|
|
| |
Abstracted the CSF size in imximage from a hardcoded value to a config
setting CONFIG_CSF_SIZE. This configuration is only enabled for secure
boot.
Increased the size of the CSF default allocation to 0x4000. This size
covers the event the worst case of 4906-bits keys.
|
| |
|
|
|
|
|
|
| |
We should not rely on pfuze_common_init to set the voltage,
may be we should remove the voltage settings in pfuze_common_init.
This patch is to setting the voltages in power_init_board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This patch is from commit "f2c5102bf3763d77a227c1cba7fcd49e3db53a1d".
"
According the latest datasheet Rev.0,2/2015, the VDDSOC_IN voltage in standby/DSM
mode is 1.05V. As we use PFM mode of pFuse and this mode has 3% tolerance issue,
so the standby mode voltage should be (1.05 * 1.03) = 1.0815, we use 1.10V as the
minimal step is 25mV. For i.MX6sx SDB RevB boards, the VDDARM and VDDSOC use the
same supply, so the DSM voltage for VDDARM also need to be updated.
"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Add udc and fastboot support
We did not use the upstream way.
Currently use CI_UDC and USB_GAGDET of upstream can make fastboot work,
but lack of flash operation, so we still use our way.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
|
Add bsp and configuration file
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
