summaryrefslogtreecommitdiff
path: root/board/freescale/mx6sabresd/mx6sabresd.c
Commit message (Collapse)AuthorAgeLines
* ENGR00330792 imx: mx6: Merge anatop registers to CCM structureYe.Li2014-09-10-2/+2
| | | | | | | | | | THe anatop registers structure is duplicated with CCM structure at PLL fields. Since we are suggested not to use the name "anatop" any longer, merge the anatop registers to the CCM structure "mxc_ccm_reg" and use CCM to replace anatop. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00326277-2 imx6: watchdog: use WDOG_B mode for wdog reset in ldo-bypass modeRobin Gong2014-08-26-1/+2
| | | | | | In ldo-bypass mode, we need trigger WDOG_B pin to reset pmic in ldo-bypass mode. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00326277-1: imx6: ldo_bypass: fix VDDARM voltage setting violate datasheetRobin Gong2014-08-26-4/+57
| | | | | | | | | Current only set VDDARM_IN@1.175V/VDDSOC_IN@1.175V before ldo bypass switch. So untile ldo bypass switch happened, these voltage setting is set in ldo-enable mode. But in datasheet, we need 1.15V + 125mV = 1.275V for VDDARM_IN. We need to downgrade cpufreq to 400Mhz and restore after ldo bypass mode switch. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00325634 iMX6DQ{DL}:SABRESD Fixed bmode booting failure for eMMCYe.Li2014-08-07-1/+1
| | | | | | | The BOOTCFG value used by bmode for SABRESD eMMC are actually for SD card. Fixed the value to correct one. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00320125 iMX6: Change to use dynamical mmcrootYe.Li2014-06-30-0/+33
| | | | | | | | | | | | | | | | | | | | | | | | | The kernel changes to fix the mmcblk index with USDHC controllers as below: mmcblk0 ---> USDHC1 mmcblk1 ---> USDHC2 mmcblk2 ---> USDHC3 mmcblk3 ---> USDHC4 So in u-boot, the "mmcroot" must be updated together. When booting from SD/MMC device, change the "mmcroot" to dynamically set according to the boot USDHC controller. It is the same mechanism as "mmcdev" used for kernel image loading. Therefore, the uboot, kernel image, dtb and rootfs are required in same SD/MMC card. To disable the mmc dynamical detection, set the "mmcautodetect" to "no", then "mmcroot" and "mmcdev" will not be overwritten. When booting from other devices which needs to load kernel, dtb and rootfs from SD/MMC card, their "mmcdev" reset vaule is CONFIG_SYS_MMC_ENV_DEV and "mmcroot" reset value is CONFIG_MMCROOT. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00319241: imx6: pfuze: set pmic mode to decrease power number in DSM modeRobin Gong2014-06-20-0/+36
| | | | | | | Currently, kernel common regulator framework can't support setting pmic mode by common DTS, so move the related code to u-boot firstly. Signed-off-by: Robin Gong <b38343@freescale.com>
* ENGR00315894-74 pfuze200: add clear print for pfuze200Ye.Li2014-06-17-1/+2
| | | | | | | | add clear print log to show pfuze200 or pfuze100 found on mx6qsabresd/ mx6slevk/mx6sx_19x19_arm2 boards. Signed-off-by: Robin Gong <b38343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-37 MX6 SabreSD: Correct IPU DI pix fmt for LDBYe.Li2014-06-17-12/+3
| | | | | | | | | | | | | The DC mapping for LVDS666 is different from that for RGB666. Currently, we set IPU DI pixel format to be LVDS666 and set LDB data width to be 24bit. This happens to make the display work normally somehow. But, the two configurations are wrong and don't match with each other. This patch corrects the IPU DI output pixel format from LVDS666 to RGB666 and LDB data width from 24bit to 18bit. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-36 MX6 SabreSD: Disable HDMI detectYe.Li2014-06-17-8/+1
| | | | | | | | | | | | | | As the HDMI splash screen feature is not well supported, we should not set it to be the default display. In case, users leave the 'panel' uboot environment variable empty and connect the board with a HDMI monitor, the HDMI detect funtion will work and enable the HDMI splash screen. So, this patch disables HDMI detect function so that users may only explicitly set the 'panel' variable to be 'HDMI' to use HDMI splash screen. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-34 imx6:dlsabresd/slevk Fix build break when enables EPDCYe.Li2014-06-17-300/+302
| | | | | | | -Use the new pins' name for imx6dl. -Change the read/write to registers by using register structure. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-17 imx6q:sabresd/sabreauto: add SATA supportYe.Li2014-06-17-4/+11
| | | | | | | | This patch adds the SATA support for i.mx6qsabresd and i.mx6qsabreauto board Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-14 i.mx6:sabreauto/sabresd/slevk Remove unused CONFIG_SYS_I2C_SLAVEYe.Li2014-06-17-1/+1
| | | | | | | The CONFIG_SYS_I2C is enabled on i.mx6 boards. So the CONFIG_SYS_I2C_SLAVE becomes to unused. Remove this setting. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-7 i.mx6q/dl/solo: sabresd/sabreauto: Add the SPI-NOR supportYe.Li2014-06-17-3/+6
| | | | | | | | | | This patch adds the SPI-NOR support for the i.mx6q/dl/solo:sabresd/auto board: - Support the SPI-NOR function with sf command, - Support the enviroment from SPI-NOR when CONFIG_SYS_BOOT_SPINOR Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-1 iMX6q/dl:SABREAUTO/SABRESD: Refactor configurations for more ↵Ye.Li2014-06-17-1/+1
| | | | | | | | | | | | | iMX6 boards 1. Make the DDR size configurable based on the boards.cfg 2. Make the FDT file configurable based on the boards.cfg 3. Add DDR and boot configuration script for iMX6dl. Change default boot from SD card. The DDR script has been updated to the v1.5 version from ddr-scripts-rel commit: bfd157a Updated MX6DL and MX6DQ ARD and SabreSD scripts. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315499-21 HDMI: splash screen function enhancementNitin Garg2014-06-13-10/+10
| | | | | | | | | | | | -Change HDMI video mode to VGA. -Add pixel clock fraction part setting in IPU driver, fix video mode timing issue. -Add overflow state clear workaround, fix kernel hang in HDMI driver issue. -Correct IPU clock to 264MHz. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-16 I2C: add I2C support on Sabre- boardNitin Garg2014-06-13-0/+126
| | | | | | | | - add I2C support on Sabresd ,Sabreauto board. - add pfuze init code based on I2C transfer in Sabre* board file. Signed-off-by: Robin Gong <b38343@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-14 ARM:imx6:sabresd/arm2 Add USB HOST BSP supportNitin Garg2014-06-13-1/+51
| | | | | | | | | Enable the USB EHCI on sabresd and arm2 boards to support USB mass storage device. Pins are configured in board_ehci_hcd_init for VBUS control. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-11 ARM:imx6 Change static environment SD/MMC storage to dynamicNitin Garg2014-06-13-0/+32
| | | | | | | | | | | | | | | | | | | imx6 boards (sabresd, sabreauto, arm2 and slevk) have multiple SD/MMC ports to boot. But current uboot hard code the SD/MMC port for environment variables storage. So if customer changes a port without modifying the configuration "CONFIG_SYS_MMC_ENV_DEV", error will issue at saving and loading environment. Implement a mechanism to detect SD/MMC port from SRC SMBR register, and override the default "mmc_get_env_devno". The "board_late_mmc_env_init" is used to set "mmcdev" when booting from SD/MMC port. Finally after booting from SD/MMC, the environment storage device and "mmcdev" are both set to current SD/MMC port. Customers don't need to re-build the image if booting from different SD/MMC port. This patch also adds SD1 and SD3 support to imx6slevk BSP, and adds support for sabreauto SD1 slot on base board. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-10 ARM:imx6:sabresd/sabreauto Add android fastboot supportingNitin Garg2014-06-13-0/+123
| | | | | | | | | | | | | | | | | | Support android features: fastboot, booti command and recovery for sabresd SD, sabresd eMMC, sabreauto SD, sabreauto NAND. For all booting media (SD, eMMC, NAND), inherits the partitions layout from v2009.08. Fastboot will detect the booting media to replace hardcoding fastboot device. SATA is not supported. FDT is supported to use the "unused" fields in bootimg header which requires the FDT to be combined into the boot.img. For non-FDT boot.img, the "unused" fields should left to NULL and is compatible to boot. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-7 Add EPDC splash screen for MX 6DL SabreSD and 6SL EVKNitin Garg2014-05-27-0/+326
| | | | | | | | | | | | | | | | | Add EPDC splash screen feature for MX6SL EVK, and MX6DL SABRESD board. - Currently, splash screen consists of a simple black border around a white screen. Done this way to save in memory footprint. - EPDC splash screen is disabled by default in the config file for MX6DL_SABRESD and MX6SL_EVK. If left enabled, the U-Boot image will not boot correctly (hang), since some additional content on the boot device (waveform file) is required for EPDC splash to work correctly. Please refer to Linux Reference Manual for how to flash WAVEFORM file. Signed-off-by: Robby Cai <R63905@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-6 ARM:imx6: Add USB gadget driver imx_udc to support Android ↵Nitin Garg2014-05-27-0/+13
| | | | | | | | | | | | | | fastboot Android fastboot leans on the USB gadget driver to communicate with host. Porting the imx_udc driver from v2009.08 with two changes: adding resource/memory release APIs and replacing the uncached memory with cache flush&invalidate operations. Pins and Clocks initialization are added to support boards: mx6qdlsabresd, mx6qdlsabreauto, mx6slevk Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-5: Support i.MX6 1.2GHz via LDO bypassNitin Garg2014-05-27-0/+67
| | | | | | | | Add check for 1.2GHz core speed. If Speed grading fuse is for 1.2GHz, enable LDO bypass and setup PMIC voltages. LDO bypass is dependent on the flatten device tree file. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ARM: mx6: Add PCIe on SabreSDPMarek Vasut2014-03-31-0/+11
| | | | | | | | | | Add support for PCIe on MX6 SabreSDP board and enable the support in the config file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Liu Ying <Ying.Liu@freescale.com>
* mx6sabresd: Return from cpu_eth_init() directlyFabio Estevam2014-01-13-7/+1
| | | | | | | | | | There is no need to print an error message when cpu_eth_init() fails because net/eth.c already prints it. In order to simplify the code, just return the value from cpu_eth_init(bis) directly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6sabresd: Fix LVDS width and color formatFabio Estevam2013-12-17-3/+3
| | | | | | | | mx6sabresd boards have a 18-bit LVDS data width and the correct color format is RGB666. Suggested-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6sabresd: Allow probing HSYNC, VSYNC and DISP_CLK signalsFabio Estevam2013-12-17-0/+9
| | | | | | | | HSYNC, VSYNC and DISP_CLK are very useful display signals for debugging. Configure them as active pins. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* MX6 SabreSD: Use readl() to read the CCM_CCGR3 registerLiu Ying2013-12-17-1/+1
| | | | | | | | Align with the context to use readl() to read the CCM_CCGR3 register with memory barrier instead of __raw_readl(). Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6sabresd: Add SPI NOR supportFabio Estevam2013-11-28-0/+19
| | | | | | | | | | | | | mx6sabre board has a m25p32 SPI NOR connected to ECSPI1 port. Add support for it. This patch allows the SPI NOR flash to be succesfully detected: => sf probe SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6sabresd: Fix wrong colors in LVDS splashFabio Estevam2013-11-28-8/+23
| | | | | | | | | | | | | Currently HDMI splash screen is selected by default on mx6sabresd boards. As LVDS is also enabled, this causes incorrect colors to be displayed im the LVDS panel. Fix this by selecting the LVDS panel as the default splash output and only keep HDMI or LVDS turned on at the same time. Acked-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* i.MX6DQ/DLS: replace pad names with their Linux kernel equivalentsEric Nelson2013-11-13-45/+45
| | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* mx6sabresd: Return error if cpu_eth_init() failsFabio Estevam2013-09-20-1/+1
| | | | | | | Currently board_eth_init() always return 0, but we should propagate the error when cpu_eth_init() fails. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6sabresd: Reset counter to prevent error messageFabio Estevam2013-09-20-0/+1
| | | | | | | | | | | | | | | | | | | If a HDMI cable is not connected, the following message is seen on boot: CPU: Freescale i.MX6Q rev1.1 at 792 MHz Reset cause: POR Board: MX6-SabreSD DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 No panel detected: default to HDMI unsupported panel HDMI Reset the 'i' variable to fix the 'unsupported panel' message. This follows the same idea of commit 47ac53d7ae (imx: nitrogen6x/mx6qsabrelite: Fix bug in board_video_skip). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6sabresd: Avoid hang when HDMI cable is not connectedFabio Estevam2013-09-20-1/+1
| | | | | | | | | | | | | | | | | | | | | Since commit d9b894603 (mx6sabresd: Add LVDS splash screen support) the following hang happens if the HDMI cable is not connected or the 'panel' variable is not set: U-Boot 2013.10-rc2-12978-g47ac53d-dirty (Sep 11 2013 - 15:07:38) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: MX6-SabreSD DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 ... Provide a check to 'dev->detect' in order to prevent the hang. Reported-by: Pardeep Kumar Singla <b45784@freescale.com> Suggested-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6sabresd: Add LVDS splash screen supportFabio Estevam2013-09-10-21/+145
| | | | | | | | | | | | | | | | | mx6sabresd boards can be connected to a Hannstar XGA LVDS panel. Add support for displaying U-boot splashscreen on it. By default, HDMI splash is selected. In order to use splash via LVDS, do the following in the U-boot prompt: setenv panel Hannstar-XGA save and reboot. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* Merge git://git.denx.de/u-boot-armStefano Babic2013-07-31-12/+1
|\ | | | | | | | | | | | | | | | | Conflicts: board/freescale/mx6qsabrelite/Makefile board/freescale/mx6qsabrelite/mx6qsabrelite.c include/configs/mx6qsabrelite.h Signed-off-by: Stefano Babic <sbabic@denx.de>
| * Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-12/+1
| | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* | mx6qsabresd: Add splash screen support via HDMIPardeep Kumar Singla2013-07-27-1/+63
|/ | | | Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
* imx: Add support for the SabreSD shipped with i.MX6DLPierre Aubert2013-06-26-0/+294
The SabreSD platform is available with i.MX6Q or i.MX6DL. This patch adds the support of the i.MX6DL. The config file and the board directory are renamed to remove the reference to the MX6Q. Signed-off-by: Pierre Aubert <p.aubert@staubli.com> CC: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
generated by cgit v1.1 at 2024-11-30 04:10:23 +0000