summaryrefslogtreecommitdiff
path: root/board/freescale/mx6qsabreauto
Commit message (Collapse)AuthorAgeLines
* MLK-14326-3 mx6qsabreauto: Enable OF_CONTROL and DM driverYe Li2017-04-05-54/+230
| | | | | | | | | | | | | | Enable OF_CONTROL and DM driver on mx6qsabreauto. 1. Add the imx6qsabreauto relevant DTS file for using DTB. 2. Modify PMIC initialization codes to use DM PMIC driver. 3. Modify to use PCA953X DM driver 4. Remove NAND from default, since the default imx6q-sabreauto.dts disabled the nand. The pins are conflicted with UART3, while UART3 is enabled. 5. For NAND build configuration, remove the USB, since the imx6q-sabreauto-gpmi-weim.dts will have pin conflicts on steer logic. 6. GPIO requests added. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14363 mx6qsabreauto: Fix ethernet PHY setting issueYe Li2017-04-05-0/+33
| | | | | | | | | | | The PHY settings for RGMII has been removed from mx6qsabreauto board codes, due to the atheros PHY driver have updated to use same configuration for AR8031 and AR8035, while this configuration is duplicated as we set in board codes. But in recent codes, the PHY driver added a patch for AR8031 independent config. So needs to add the PHY settings back to the board codes. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12996 imx: mx6dqp/dq: Fix SATA read/write fail after booting from SATAYe Li2017-04-05-3/+6
| | | | | | | | | | | | | | | We found a issue in PLL6 ENET that changing the bit[1:0] DIV_SELECT for ENET ref clock will impact the SATA ref 100Mhz clock. If SATA is initialized before this changing, SATA read/write can't work after it. And we have to re-init SATA. The issue can reproduce on both i.MX6DQP and i.MX6DQ. IC investigation is ongoing. This patch is an work around that moves the ENET clock setting (enable_fec_anatop_clock) from ethernet init to board_init which is prior than SATA initialization. So there is no PLL6 change after SATA init. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit fd8fbf7fa0b10199ac89cd13cae851149f51accb)
* MLK-11230 imx6: USB: Modify OTG ID pin pad setting to pull upYe.Li2017-04-05-1/+5
| | | | | | | | | | | Set the ID pin pad to pull up not the pull down at default, otherwise we can't enter the device mode, but always detect as host. After this change we have to use portA cable to play as host, and use portB cable for device. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit b315d6b36a913d75d25284320e69050ebdf7a7eb)
* MLK-12493-1 Add support for various boot deviceYe Li2017-04-05-9/+38
| | | | | | | | | | Add support for various boot devices like NAND, QSPINOR, SPINOR, eMMC, EIMNOR, SATA. Modify board level files to support the feature and add corresponding defconfig files Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 72c35e80b86f7f75a52db45959793882bb730793)
* MLK-12500-2 HAB: Add commented secure boot configurationsYe Li2017-04-05-0/+16
| | | | | | | | | | | | CONFIG_SECURE_BOOT is used for signed image building, this configuration is not enabled at default. Comment it in mx6/mx7 common header file. Users can uncomment it to enable. Also add CONFIG_CSF_SIZE for defining the CSF reserved size and resize the CONFIG_CSF_SIZE to 0x4000 to align with v2016.03. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 01cc7d9bc205251c13712418d51f3a4d7b20861b)
* MLK-12495 mx6: Add LDO bypass supportYe Li2017-04-05-0/+38
| | | | | | | | | | | | | | | | Port LDO bypass support from v2015 to support the features: 1. Add check for 1.2GHz core speed. If Speed grading fuse is for 1.2GHz, enable LDO bypass and setup PMIC voltages. LDO bypass is dependent on the flatten device tree file. 2. We set WDOG_B in set_anatop_bypass() before, because it is the only case, but now on i.mx6sabreauto board, we didn't use ldo-bypass mode, but have to use WDOG_B to reboot whole board, so split these code to independent function so that board file can call it freely. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 5b87d04dba66fa45375d59648838ef89f559f75d)
* MLK-12436-8: imx: mx6qsabreauto: misc board updatePeng Fan2017-04-05-34/+198
| | | | | | | | | | | | | | | | To Align with imx_v2016.03. 1. Add USDHC1 support on mother board 2. Add SPINOR flash support. 3. Add enet ref clk pinmux setting and enet settings 4. Use CONFIG_SYS_USE_EIMNOR to wrap eimnor settings. 5. update mmc board settings 6. update board_init and move nand settings to board_init, but not in board_early_init_f 7. update pmic settings to align with datasheet. Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit f05f2281548ab7b47f69b2c517eb6f85ad09a5d2) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12436-7: imx: mx6qsabreauto: add solo board supportPeng Fan2017-04-05-0/+119
| | | | | | | | Add solo version ddr script and build target. Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit 54af2f744c663ac2326c1488a26fac0c4ccdad09) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14261-1 mx6solo: Rename the CONFIG_MX6SOLO to CONFIG_MX6SYe Li2017-04-05-1/+1
| | | | | | | | | | | | | Since there is already CONFIG_MX6S used for i.MX6 SOLO in u-boot codes, we don't need to add new CONFIG_MX6SOLO. Rename the existing CONFIG_MX6SOLO to CONFIG_MX6S. Additional, for CONFIG_MX6S, we should select CONFIG_MX6DL. The major difference for these two chips are core number and DDR controller. So all duallite relevant definitions can apply to solo. User can combine the two configs if any code only apply to solo or duallite. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12436-6: imx: mx6dqpsabreauto: update ddr script to 1.13Peng Fan2017-04-05-5/+6
| | | | | | | | | | | | | | | | | | | | DDR script: http://sw-stash.freescale.net/projects/IMX/repos/ddr-scripts-rel/commits/8111e4d0cd81226899be637013048281e3c097b4 http://compass.freescale.net/livelink/livelink?func=ll&objId=234753630&objAction=browse&viewType=1 arik_r2_sabre_ddr3_528_1.13.inc is for sabre-AI Patch in imx_v2015.04: " commit 5fb08a4dcc7b8478fc4236b90ad8dc2190cf94e7 Author: Peng Fan <Peng.Fan@freescale.com> Date: Wed Nov 4 16:30:47 2015 +0800 "MLK-11825 imx: mx6dqp: update ddr script to 1.13" " Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit d756891b9d303e456f59a18d5fa81969a7f37337) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14250-4 mx6dq/dl/dqp: Add plugin boot support for sabre boardsYe Li2017-04-05-3/+696
| | | | | | | | Add plugin.S for plugin boot initialization on mx6dq/dl/dqp sabresd and sabreauto boards. Need to set "CONFIG_USE_IMXIMG_PLUGIN" for this feature. Add the configurations for the plugin enabled buiding. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-12434-3: mx6sabre: dynamic setting mmcdev and mmcrootPeng Fan2017-04-05-1/+25
| | | | | | | Dynamic setting mmcdev and mmcroot for mx6sabresd and mx6qsabreauto. Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit 14040e07549a394500c11e815f31299e4fb0ac50)
* mx6qsabreauto: Fix the EIM clock for the mx6qp variantFabio Estevam2017-01-02-0/+28
| | | | | | | | | | | | | | | | | | | On the MX6Q the aclk_eim_slow_podf field is '1' after POR, while on the MX6DQP it is '3'. This makes the EIM clock to be only 66MHz on the mx6qp variant, instead of 132 MHz. Instead of relying on the POR values for the CSMR1 register, make sure to manually configure the clk_eim_slow_sel field as '00' so that EIM clock is derived from AXI clock and the aclk_eim_slow_podf field as '1' so that EIM clock can be AXI clock divided by 2. This way a consistent EIM clock frequency is configured for all the mx6 variants. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
* treewide: replace #include <asm/errno.h> with <linux/errno.h>Masahiro Yamada2016-09-23-1/+1
| | | | | | | | | | | Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have the same content. (both just wrap <asm-generic/errno.h>) Replace all include directives for <asm/errno.h> with <linux/errno.h>. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> [trini: Fixup include/clk.] Signed-off-by: Tom Rini <trini@konsulko.com>
* mx6qsabreauto: Avoid hardcoded RAM sizeVanessa Maegima2016-07-12-1/+1
| | | | | | | | | Instead of passing the total RAM size via PHYS_SDRAM_SIZE option, we should better use imx_ddr_size() function, which automatically determines the RAM size. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
* imx: mx6qsabreauto: drop duplicated net phy configurationPeng Fan2016-05-31-33/+0
| | | | | | | | | | | | | In 'commit d584c68ce0f5bf2f430ccfb2ba00bd506206fb91', ar8031 is changed to use ar8035_config. ar8035_config actually does the same thing as mx6_rgmii_rework, so drop mx6_rgmii_rework and board_phy_config. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Stefano Babic <sbabic@denx.de>
* board: mx6sabresd/auto: use simpler runtime cpu dection macrosPeng Fan2016-05-24-2/+2
| | | | | | | | Use simpler runtime cpu dection macros. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* MAINTAINERS: Update Peng Fan's email addressFabio Estevam2016-03-02-1/+1
| | | | | | | Use Peng Fan's new NXP email address in MAINTAINERS files. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
* MAINTAINERS/mailmap: Update my email addressFabio Estevam2016-01-11-1/+1
| | | | | | Update my email address to the NXP account. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* imx: mx6qsabreauto: support lvds displayPeng Fan2016-01-03-3/+84
| | | | | | | | | | | Move setup_display from board_early_init_f to board_init. Add more clock settings. Add blacklight iomux setting. Add display_info_t info for the lvds screen. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* imx: boards: Add maintainers infoPeng Fan2015-09-24-0/+2
| | | | | | | Add MAINTAINERS info for mx6slevk_spl, mx6ul_9x9_evk and mx6qpsabreauto. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* mx6: remove SYS_SOC from board KconfigPeng Fan2015-09-13-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | Remove duplicated SYS_SOC Kconfig entry from board Kconfig, because we have this entry in arch/arm/cpu/armv7/mx6/Kconfig. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: "Eric Bénard" <eric@eukrea.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Marek Vasut <marex@denx.de> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com> Acked-by: Markus Niebel <Markus.Niebel@tq-group.com> Acked-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* imx: clock support enet2 anatop clock supportPeng Fan2015-09-02-1/+1
| | | | | | | | | | | | | | | | To i.MX6SX/UL, two ethernet interfaces are supported. Add ENET2 clock support: 1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed. To value 1, only i.MX6SX/UL can pass the check. 2. Modify board code who use this api to follow new api prototype. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Heiko Schocher <hs@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefan Roese <sr@denx.de> Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
* imx: mx6qpsabreauto: Add MX6QP SABREAUTO CPU3 board supportPeng Fan2015-08-02-7/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add DDR script for mx6qpsabreauto board. 2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9] and init the enet pll output to 125Mhz. 3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN. Build target: mx6qpsabreauto_config Boot Log: U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 34C Reset cause: POR Board: MX6Q-Sabreauto revA I2C: ready DRAM: 2 GiB PMIC: PFUZE100 ID=0x10 Flash: 32 MiB NAND: 0 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment No panel detected: default to HDMI Display: HDMI (1024x768) In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 Note: In this patch, we still add a new config mx6qpsabreauto_config, since SPL is not supported now, and IMX_CONFIG is needed at build time, so add this config. Future, when SPL is converted, this config can be removed. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Signed-off-by: Robin Gong <b38343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx: mx6sabresd/sabreauto runtime setting fdt_filePeng Fan2015-08-02-0/+9
| | | | | | | | | | | | | Detect the SOC and board variant at runtime and change the dtb name, but not hardcoding the fdt_file env variable. Take the following patch as a reference. Íd58699b157df75f1aa0b363ea9c21add21a0c "mx6cuboxi: Load the correct 'fdtfile' variable" Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* imx:mx6 set normal APS and standby PFM modePeng Fan2015-02-11-0/+6
| | | | | | | | To normal mode, use APS switching mode. To standy mode, use PFM switching mode. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
* imx: mx6qsabreauto: Change to use common GPMI IO clock functionYe.Li2015-02-10-23/+2
| | | | | | | | Since a clock function setup_gpmi_io_clk is implemented for GPMI IO clock settings, change to use this common function in GPMI setup. Signed-off-by: Ye.Li <B37916@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* imx: imx6q/dlsabreauto: Add PMIC Pfuze100 supportYe.Li2014-11-20-0/+15
| | | | | | | Add the pfuze100 initialization in power_init_board for imx6q/dl sabreauto board. Signed-off-by: Ye.Li <B37916@freescale.com>
* mx6qsabreauto: Add parallel NOR flash supportFabio Estevam2014-11-20-1/+79
| | | | | | | | | | | | | | | | | | | | | mx6sabreauto boards come with 32 MiB of parallel NOR flash. Add support for it: U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: MX6Q-Sabreauto revA I2C: ready DRAM: 2 GiB Flash: 32 MiB NAND: 0 MiB Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is not used. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx: mx6q/dlsabreauto: And NAND flash supportYe.Li2014-11-13-0/+66
| | | | | | | | | | | The i.MX6Q/DL sabreauto board has one NAND socket, set the CONFIG_NAND_MXS and relevant NAND configurations to enable the MXS NAND flash driver. Add board level codes to set IOMUX and clock for GPMI-NAND and BCH module. Signed-off-by: Ye.Li <B37916@freescale.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-11-05-0/+93
|\
| * imx: mx6 sabreauto: Add board support for USB EHCIYe.Li2014-11-03-0/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On mx6 sabreauto board, there are two USB ports: 0: OTG 1: HOST The EHCI driver is enabled for this board, but the IOMUX and VBUS power control is not implemented, which cause both USB port failed to work. This patch fix the problem by adding the board support codes. Since the power control uses the GPIO pin from port expander MAX7310, the PCA953X driver is enabled for accessing the MAX7310. The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting its daisy chain. Add a new function "imx_iomux_set_gpr_register" to handle GPR register setting. Signed-off-by: Ye.Li <B37916@freescale.com>
* | kconfig: arm: introduce symbol for ARM CPUsGeorges Savoundararadj2014-10-29-3/+0
|/ | | | | | | | | | | | | | | | | This commit introduces a Kconfig symbol for each ARM CPU: CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136, CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100. Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected for CPU_ARM1176 and CPU_V7. For each target, the corresponding CPU is selected and the definition of SYS_CPU in the corresponding Kconfig file is removed. Also, it removes redundant "string" type in some Kconfig files. Signed-off-by: Georges Savoundararadj <savoundg@gmail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
* mx6qsabreauto: Add HDMI supportFabio Estevam2014-10-21-1/+59
| | | | | | Let HDMI splash screen support work by default. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* ARM: i.MX: provide declaration for board_spi_cs_gpioEric Nelson2014-10-21-0/+1
| | | | | | | | Provide a public declaration of the board_spi_cs_gpio() callback for i.MX SPI chip selects to prevent the warning "Should it be static?" when compiling with "make C=1". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* Merge remote-tracking branch 'u-boot-imx/master'Albert ARIBAUD2014-10-08-8/+8
|\ | | | | | | | | | | | | The single file conflict below is actually trivial. Conflicts: board/boundary/nitrogen6x/nitrogen6x.c
| * Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic2014-09-22-5/+0
| |\
| * | mx6qsabreauto: Staticize when possibleFabio Estevam2014-09-16-8/+8
| | | | | | | | | | | | | | | | | | Turn all local symbols into static in order to make sparse happy. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | | spi: mxc: fix sf probe when using mxc_spiNikita Kiryanov2014-09-24-0/+7
| |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MXC SPI driver has a feature whereas a GPIO line can be used to force CS high across multiple transactions. This is set up by embedding the GPIO information in the CS value: cs = (cs | gpio << 8) This merge of cs and gpio data into one value breaks the sf probe command: if the use of gpio is required, invoking "sf probe <cs>" will not work, because the CS argument doesn't have the GPIO information in it. Instead, the user must use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must type "sf probe 15872". This is inconsistent with the description of the sf probe command, and forces the user to be aware of implementaiton details. Fix this by introducing a new board function: board_spi_cs_gpio(), which will accept a naked CS value, and provide the driver with the relevant GPIO, if one is necessary. Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Eric Benard <eric@eukrea.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Marek Vasut <marex@denx.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* | kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-13-5/+0
|/ | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Add board MAINTAINERS filesMasahiro Yamada2014-07-30-0/+7
| | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-30-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* mx6sabreauto: Add the mx6dual-lite variantFabio Estevam2014-05-28-0/+130
| | | | | | Tested by booting a mainline kernel via TFTP. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6qsabreauto: Update imximage.cfgFabio Estevam2014-02-11-77/+59
| | | | | | Use the latest DDR and clock settings as the one from Freescale BSP. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6qsabreauto: Return from cpu_eth_init() directlyFabio Estevam2014-01-13-7/+1
| | | | | | | | | | There is no need to print an error message when cpu_eth_init() fails because net/eth.c already prints it. In order to simplify the code, just return the value from cpu_eth_init(bis) directly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* i.MX6 (DQ/DLS): use macros for mux and pad declarationsEric Nelson2013-12-17-1/+1
| | | | | | | | | | | | | | | | | | | | This allows the use of either or both declarations from the files mx6q_pins.h and mx6dl_pins.h. All board files should include <asm/arch/mx6-pins.h> with one of the following defined in boards.cfg MX6Q - for boards targeting i.MX6Q or i.MX6D MX6DL - for boards targeting i.MX6DL MX6S - for boards targeting i.MX6S MX6QDL - for boards that support any of the above with run-time detection Pad declarations will be MX6_PAD_x for single-variant boards and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both processor classes. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
* i.MX6DQ/DLS: replace pad names with their Linux kernel equivalentsEric Nelson2013-11-13-30/+30
| | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* board: arm: convert makefiles to Kbuild styleMasahiro Yamada2013-11-01-20/+1
| | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
* mx6qsabreauto: Return error if cpu_eth_init() failsFabio Estevam2013-09-20-1/+1
| | | | | | | Currently board_eth_init() always return 0, but we should propagate the error when cpu_eth_init() fails. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
generated by cgit v1.1 at 2024-08-24 16:45:15 +0000