arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	imx: mx6dlarm2: Add support for i.MX6Q/DL arm2 LPDDR2 boards	Ye.Li	2014-09-30	-6/+183
\| \| \| \| \| \| \| \|	Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2 arm2 board. Since the LPDDR2 arm2 board has different DDR size, use CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE. Signed-off-by: Ye.Li <B37916@freescale.com>
*	Add GPL-2.0+ SPDX-License-Identifier to source files	Wolfgang Denk	2013-07-24	-17/+1
\| \| \| \| \| \|	Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
*	Fix references to the documentation files	Anatolij Gustschin	2013-05-10	-1/+1
\| \| \| \| \| \| \| \| \| \| \| \|	Many boot image configuration files refer to the appropriate documentation file, but these references contain typos in the directory and file name. Fix them. Also fix reference to doc/README.SPL file. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
*	imximage.cfg: run files through C preprocessor	Troy Kisky	2013-01-22	-42/+46
\| \| \| \| \| \| \| \| \| \| \| \|	The '#' used as comments in the files cause the preprocessor trouble, so change to /* */. The mkimage command which uses this preprocessor output was moved to arch/arm/imx-common/Makefile .gitignore was updated to ignore .cfgtmp files. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
*	mx6: Avoid writing to read-only bits in imximage.cfg	Vikram Narayanan	2012-07-07	-1/+1
\| \| \| \| \|	If in case this is valid according to the latest datasheet, ignore this patch. Acked-by: Marek Vasut <marex@denx.de>
*	i.MX6: arm2: Add AXI cache and Qos setting	Dirk Behme	2012-04-17	-0/+6
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	Do the same AXI cache and Qos settings done already in the SabreLite imximage.cfg for the ARM2 board, too. It fixes a display flash issue caused by low priority of the display IDMA channel. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Chen <b02280@freescale.com> CC: Jason Liu <r64343@freescale.com> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <festevam@gmail.com> Acked-by: Jason Liu <r64343@freescale.com>
*	i.mx6q: mx6qarm2: Enable the usboh3 clock	Eric Nelson	2012-01-16	-1/+1
\| \| \| \| \| \| \| \| \|	Bits 0 and 1 of CCM_CCGR7 are the usboh3 clock enable bits. Enabling this clock is necessary for the USB download. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> CC: Jason Hui <jason.hui@linaro.org> Acked-by: Jason Hui <jason.hui@linaro.org>
*	i.mx: i.mx6q: add the initial support for i.mx6q ARM2 board	Jason Liu	2011-12-09	-0/+167
	Add the initial support for Freescale i.MX6Q Armadillo2 board Support: MMC boot from slot 0/1, debug UART(UART4), usdhc. There is two MMC slots on the boards: mmc dev 0 -> connect USDHC3 -> the lower slot on the board, mmc dev 1 -> connect USDHC4 -> the upper slot on the board, Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Stefano Babic <sbabic@denx.de> Tested-by: Dirk Behme <dirk.behme@de.bosch.com>