summaryrefslogtreecommitdiff
path: root/board/freescale/mx53loco
Commit message (Collapse)AuthorAgeLines
* mx53loco: Disable printing cpuinfoFabio Estevam2015-04-08-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 32df39c741788e ("mx5: fix get_reset_cause") we have the following boot messages on a mx53qsb: U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39) CPU: Freescale i.MX53 rev2.1 at 800 MHz Reset cause: POR Board: MX53 LOCO I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial CPU: Freescale i.MX53 rev2.1 at 1000 MHz Reset cause: unknown reset Net: FEC [PRIME] The CPU and Reset cause lines appear twice. Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via I2C to raise the CPU voltage so that it can run at 1GHz. To avoid such misleading double printings, disable printing cpu info for now. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
* mx5: fix get_reset_causeStefano Babic2015-03-05-16/+0
| | | | | | | | | | | | commit d9f43c8f5c1d7ed27c99a06be85a4bb64b2c73fb sets get_reset_cause() as static, but this conflicts with mx5 where its prototype is in sys_proto.h. Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco, factorizing the call for this board. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org>
* mx53loco: Fix boot hang during reboot stress testFabio Estevam2015-02-10-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently by running the following test: => setenv bootcmd reset => save => reset , we observe a hang after approximately 20-30 minutes of stress reboot test. Investigation of this issue revealed that when a single DDR chip select is used, the hang does not happen. It only happens when the two chip selects are active. MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence": "The controller must keep the memory lines quiet (except for CK) for the ZQ calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256 for other ZQCL and 64 for ZQCS)." According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL: "Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines. Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)" So make sure to activate one chip select at time (CS0 first and then CS1 later), so that the required JEDEC delay is respected for each chip select. With this change applied the board has gone through three days of reboot stress test without any hang. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mx53loco: Fix error handling in board_mmc_init()Fabio Estevam2014-11-20-4/+6
| | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53loco: Change 'fdt_file' dynamicallyFabio Estevam2014-11-13-0/+4
| | | | | | | | | | | | | Since kernel 3.15 there are two dtb's for the imx53-qsb board: imx53-qsb.dtb - For the boards with DA9053 PMIC imx53-qsrb.dtb - For the boards with MC34708 PMIC Change the 'fdt_file' dynamically, so that the correct dtb can be used depending on the board variant. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
* kconfig: arm: introduce symbol for ARM CPUsGeorges Savoundararadj2014-10-29-3/+0
| | | | | | | | | | | | | | | | | This commit introduces a Kconfig symbol for each ARM CPU: CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136, CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100. Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected for CPU_ARM1176 and CPU_V7. For each target, the corresponding CPU is selected and the definition of SYS_CPU in the corresponding Kconfig file is removed. Also, it removes redundant "string" type in some Kconfig files. Signed-off-by: Georges Savoundararadj <savoundg@gmail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-13-5/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Add board MAINTAINERS filesMasahiro Yamada2014-07-30-0/+6
| | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-30-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* arm: mx5: Avoid hardcoding memory sizes on MX53QSBMarek Vasut2014-03-31-7/+24
| | | | | | | | | | | | | | | | | | | The DRAM size can be easily detected at runtime on i.MX53. Implement such detection on MX53QSB and adjust the rest of the macros accordingly to use the detected values. An important thing to note here is that we had to override the function for trimming the effective DRAM address, get_effective_memsize(). That is because the function uses CONFIG_MAX_MEM_MAPPED as the upper bound of the available DRAM and we don't have gd->bd->bi_dram[0].size set up at the time the function is called, thus we cannot put this into the macro CONFIG_MAX_MEM_MAPPED . Instead, we use custom override where we use the size of the first DRAM block which we just detected. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de>
* Move #ifdef(CONFIG_DISPLAY_CPUINFO) from caller to calleeMasahiro Yamada2014-02-19-0/+2
| | | | | | | | | | | | | | | | | | - When CONFIG_DISPLAY_CPUINFO is not enabled, print_cpuinfo() should be defined as an empty function in a header, include/common.h - Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif from caller, common/board_f.c and arch/arm/lib/board.c - Remove redundant prototypes in arch/arm/lib/board.c, arch/arm/include/asm/arch-am33x/sys_proto.h and board/nokia/rx51/rx51.h, keeping the one in include/common.h - Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition where it is missing Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* imx: Explicitly pass the I2C bus number in pmic_init()Fabio Estevam2013-12-17-1/+1
| | | | | | | | | | | | | | | | | | The pmic_init() function has the I2C or SPI bus number that is connected to the PMIC. Instead of passing I2C_PMIC, explicitly pass the I2C bus number via I2C_x definition. The motivation for doing this is to avoid people just doing a copy and paste of I2C_PMIC into their board file when another I2C bus is actually used to interface to their PMIC. This also makes more obvious which is the I2C bus connected to the PMIC, without having to search in the source code for the meaning of the 'I2C_PMIC' number. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* board: arm: convert makefiles to Kbuild styleMasahiro Yamada2013-11-01-22/+2
| | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-65/+4
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-05-30-1/+1
|\ | | | | | | | | | | Conflicts: common/cmd_fpga.c drivers/usb/host/ohci-at91.c
| * Fix references to the documentation filesAnatolij Gustschin2013-05-10-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Many boot image configuration files refer to the appropriate documentation file, but these references contain typos in the directory and file name. Fix them. Also fix reference to doc/README.SPL file. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* | imx: mx53loco: Convert to iomux-v3Benoît Thébaudeau2013-05-05-223/+113
|/ | | | | | There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imximage.cfg: run files through C preprocessorTroy Kisky2013-01-22-40/+43
| | | | | | | | | | | | The '#' used as comments in the files cause the preprocessor trouble, so change to /* */. The mkimage command which uses this preprocessor output was moved to arch/arm/imx-common/Makefile .gitignore was updated to ignore .cfgtmp files. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* mx53loco: Add support for SEIKO 4.3'' WVGA panelFabio Estevam2013-01-09-5/+35
| | | | | | | | | | | Add support for the Seiko 4.3'' WVGA panel on mx53loco. By default, the CLAA WVGA panel is selected. In order to support the Seiko panel, the enviroment variable 'panel' must be set to 'seiko'. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53loco: Improve error handling on power_init()Fabio Estevam2013-01-05-10/+51
| | | | | | | | | | | Make the error handling more robust. Check if each one of the PMIC writes fail and if they do, just return immediately. Also, print the cause for the failures. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53loco: Remove unneeded 'retval' variableFabio Estevam2013-01-05-7/+6
| | | | | | | | | | | commit c73368150 (pmic: Extend PMIC framework to support multiple instances of PMIC devices) introduced an extra 'retval' variable, but this is not necessary since we have already the variable 'ret' in place. So use 'ret' to store the return values from the pmic related calls and remove 'retval'. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53loco: Call PMIC related functions from board_late_init()Fabio Estevam2012-12-27-2/+8
| | | | | | | | | | | | | | | | | | | | | | | Since commit c733681 (pmic: Extend PMIC framework to support multiple instances of PMIC devices) mx53loco fails to allocate the memory for PMIC: U-Boot 2013.01-rc2-dirty (Dec 20 2012 - 15:55:01) Board: MX53 LOCO I2C: ready DRAM: 1 GiB pmic_alloc: No available memory for allocation! pmic_init: POWER allocation error! CPU: Freescale i.MX53 family rev2.0 at 800 MHz Reset cause: POR MMC: FSL_SDHC: 0, FSL_SDHC: 1 Calling the PMIC related functions at a later stage, ie, from board_late_init() fixes the issue. Reported-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Stefano Babic <sbabic@denx.de>
* mx53loco: Fix PMIC nameFabio Estevam2012-12-13-1/+1
| | | | | | | | | commit c73368150 (pmic: Extend PMIC framework to support multiple instances of PMIC devices) has incorrectly passed the PMIC name under the FSL PMIC case. Fix that by passing "FSL_PMIC" as the parameter of pmic_get. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini2012-11-19-65/+99
|\
| * mx53loco: Fix build error when CONFIG_VIDEO is disabledVikram Narayanan2012-11-14-65/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The inclusion of LCD patch into mx53loco breaks the build when CONFIG_VIDEO is disabled. Fix this by splitting the video related stuff to a new file. Also rename the function lcd_iomux to setup_iomux_lcd to make the namings aligned with the other iomux functions. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* | pmic: Extend PMIC framework to support multiple instances of PMIC devicesŁukasz Majewski2012-11-14-5/+16
|/ | | | | | | | | | | | | | | | | | The PMIC framework has been extended to support multiple instances of the variety of devices responsible for power management. This change allows supporting of e.g. fuel gauge, charger, MUIC (Micro USB Interface Circuit). Power related includes have been moved to ./include/power directory. This is a first of a series of patches - in the future "pmic" will be replaced with "power". Two important issues: 1. The PMIC needs to be initialized just after malloc is configured 2. It uses list to hold information about available PMIC devices Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
* i.MX: ipufb: add const to fb_videomode declarationsEric Nelson2012-10-16-1/+1
| | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* mxc: Fix SDHC multi-instance clockBenoît Thébaudeau2012-10-16-0/+3
| | | | | | | | | | | | | | | | | | On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not suitable for the multi-instance use case (initialization made directly with fsl_esdhc_initialize()). This patch fixes this issue by adding a configuration field for the SDHC input clock frequency. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Eric Bénard <eric@eukrea.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Jason Liu <r64343@freescale.com> Cc: Matt Sealey <matt@genesi-usa.com> Cc: Andy Fleming <afleming@gmail.com>
* mx5/6: Define default SoC input clock frequenciesBenoît Thébaudeau2012-10-15-1/+1
| | | | | | | | | | | Define default SoC input clock frequencies for i.MX5/6 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Liu <r64343@freescale.com> Cc: Matt Sealey <matt@genesi-usa.com> Cc: Fabio Estevam <fabio.estevam@freescale.com>
* fsl_esdhc: Remove cache snooping for i.MXBenoît Thébaudeau2012-09-01-2/+2
| | | | | | | | | | | | | | | The cache snooping feature of Freescale's eSDHC IP is not available on i.MX, so disable it globally for this architecture. This avoids setting no_snoop for all i.MX boards, and it prevents setting a reserved bit of a reserved register if fsl_esdhc_mmc_init() is used on i.MX, like in arch/arm/cpu/armv7/imx-common/cpu.c/cpu_mmc_init(). Since no_snoop was only used on i.MX, get rid of it BTW. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com>
* mx5:Use IMX_GPIO_NR macroAshok Kumar Reddy2012-09-01-4/+4
| | | | Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com>
* mx53loco: Use IMX_GPIO_NR macroFabio Estevam2012-09-01-1/+1
| | | | Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* MX5: mx53loco: do not overwrite the consoleStefano Babic2012-09-01-6/+6
| | | | | | | | | On this board, the console is always set to the serial line. Do not allow to overwrite it when video is enabled. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53loco: Remove unused SOBJSFabio Estevam2012-07-07-4/+3
| | | | | | | | There is no .S file in this directory, so just remove SOBJS. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
* mx53loco: Fix revision of Dialog boardsFabio Estevam2012-07-07-5/+7
| | | | | | | | | | | | Original code was assuming that the fuse revision version for all mx53loco boards based on Dialog PMIC was the same, which is not the case. Force the revision of all Dialog-based boards to 0. This fixes a kernel crash when PMIC is accessed in the 2.6.35 kernel for Dialog rev E boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53loco: Add LCD supportFabio Estevam2012-05-25-0/+72
| | | | | | | | | | | | Add support for CLAA07LC0ACW LCD that connects to the mx53loco board. Configure the board to show the Linux logo on the LCD. Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account the framebuffer usage. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
* mx53loco: Remove unneeded gpio_set_value()Fabio Estevam2012-05-15-3/+2
| | | | | | | | | | There is no need to set the VBUS power enable to 0 first and then to 1. Set it to 1 in the gpio_direction_output() function. While at it, use the standard naming convention for the GPIO comment. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53loco: Add CONFIG_REVISION_TAGFabio Estevam2012-05-15-0/+12
| | | | | | | | | | | FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information. The kernel uses this data to distinguish between Dialog versus mc34708 based boards, and also to distinguish between revA and revB of the mc34708 based boards. Suggested-by: Yu Li <yk@magniel.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mx53loco: Turn on VUSB regulatorFabio Estevam2012-05-15-0/+9
| | | | | | | | | | | | | | | | | | On the mx53loco board with mc34708 PMIC it is necessary to turn on VUSB regulator so that the mx53 USBH1 PHY receives the 3.3V voltage. Tested by inserting a USB pen drive in the upper USB slot (USBH1) and then issued the commands: usb start usb info ,which correctly detected and printed the USB pen drive information. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mx53loco: Add mc34708 support and set mx53 frequency at 1GHzFabio Estevam2012-05-15-12/+36
| | | | | | | | Add mc34708 support and set mx53 core frequency at its maximum value of 1GHz. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* pmic: dialog: Avoid name conflictsFabio Estevam2012-05-15-1/+1
| | | | | | | | | | As mx53loco board has two variants: one with Dialog PMIC and another with FSL MC34708 PMIC, we need to be able to build both drivers. Change pmic_init() and PMIC_NUM_OF_REGS names to avoid build conflicts when both drivers are present. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mx53loco: Add support for 1GHz operation for DA9053-based boardsFabio Estevam2012-05-15-0/+71
| | | | | | | | | | | | | | | There are two types of mx53loco boards: initial boards were built with a Dialog DA9053 PMIC and more recent version is based on a Freescale MC34708 PMIC. Add DA9053 PMIC support and adjust the required voltages and clocks for running the CPU at 1GHz. Tested on both versions of mx53loco boards. In the case of a MC34708-based board the CPU operating voltage remains at 800MHz. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by : Stefano Babic <sbabic@denx.de>
* mx53loco: Allow to print CPU information at a later stageFabio Estevam2012-05-15-0/+22
| | | | | | | | | | | Print CPU information within board_late_init(). This is in preparation for adding 1GHz support, which requires programming a PMIC via I2C. As I2C is only available after relocation, print the CPU information later at board_late_init(), so that the CPU frequency can be printed correctly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* MX53: mx53loco: Add SATA supportStefano Babic2012-05-15-0/+3
| | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
* MX53: DDR: Fix ZQHWCTRL field TZQ_CSTroy Kisky2012-04-16-1/+1
| | | | | | | | | Currently, board files are setting this field to 0x01 which the manual says is a reserved value. Change to use the default of 0x02 - 128 cycles. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53loco: Use gpio_direction_input prior to gpio_get_valueFabio Estevam2012-02-27-0/+2
| | | | | | | | | Use gpio_direction_input prior to gpio_get_value. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <r64343@freescale.com>
* mmc: Change board_mmc_getcd() function prototype.Thierry Reding2012-01-08-4/+5
| | | | | | | | | | | | | | | | | | | | | The new API no longer uses the extra cd parameter that was used to store the card presence state. Instead, this information is returned via the function's return value. board_mmc_getcd() returns -1 to indicate that no card-detection mechanism is implemented; 0 indicates that no card is present and 1 is returned if it was detected that a card is present. The rationale for this change can be found in the following email thread: http://lists.denx.de/pipermail/u-boot/2011-November/110180.html In summary, the old API was not consistent with the rest of the MMC API which always passes a struct mmc as the first parameter. Furthermore the cd parameter was used to mean "card absence" in some implementations and "card presence" in others. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Tested-by: Jason Liu <jason.hui@linaro.org>
* Fix building for mx51evk boardAnatolij Gustschin2011-12-19-1/+2
| | | | | | | | | | | | | Fix: mx51evk.c:206:6: error: conflicting types for 'board_ehci_hcd_init' /u-boot/include/usb/ehci-fsl.h:254:5: note: previous declaration of 'board_ehci_hcd_init' was here We also fix board_ehci_hcd_init() for mx53loco board. Building for mx53loco worked since <usb/ehci-fsl.h> is not included here. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* USB: mx53loco: add end enable USB host support on port 1Wolfgang Grandegger2011-12-11-0/+10
| | | | | | | | Signed-off-by: Wolfgang Grandegger <wg@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Cc: Wolfgang Grandegger <wg@denx.de> Cc: Jason Liu <r64343@freescale.com>
* mx53loco: Configure the pins as GPIOs prior to using gpio_get_valueFabio Estevam2011-12-06-0/+3
| | | | | | | | Configure the pins as GPIO prior to using gpio_get_value. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <jason.hui@linaro.org>
generated by cgit v1.1 at 2024-11-01 23:28:40 +0000