summaryrefslogtreecommitdiff
path: root/board/freescale/mx53_loco
Commit message (Collapse)AuthorAgeLines
* ENGR00157538 remove VDIG_PLL setting in plug-in codeLily Zhang2011-09-23-5/+0
| | | | | | | | According to the datasheet, VDIG_PLL needs to be increased to 1.3v for TO2.0. This operation has been done in the low_level_init.S. Remove the duplicated code here. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00155569 mc34708: change global reset time as 4s of LOCO and PCBARobin Gong2011-09-19-0/+11
| | | | | | reduce the time of global reset to 4s in the boards of loco and pcba Signed-off-by: Robin Gong <B38343@freescale.com>
* ENGR00156389: turn off child clocks before reconfigure perclk_rootTerry Lv2011-09-13-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | In addition to ensuring that PERCLK remains at least 2.5 times slower than the AHB clock, certain steps need to be followed to ensure robust operation of PERCLK when reconfiguring the PERCLK clock source. To properly configure the PERCLK clock source, the following steps are required: 1.In the CCGR registers, gate the clocks to all PERCLK-dependent modules. 2.Select the desired input clock for the PERCLK root clock (to be either source from the peripherals main source clock or the lp_apm clock source). Refer to the CMCBR register, perclk_lp_apm_sel bit. 3.Configure the perclk_pred1, perclk_pred2, and perclk_podf dividers to the desired setting. Refer to the CBCDR register for details. 4.In the CCGR registers, enable the desired clocks for the PERCLK-dependent module clocks. Certain steps are required to reconfigure perclk_root. If don't follow these steps, GPT timer may stop and the kernel stops at " "Calibrating delay loop". Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00156098 mx53_smd/mx53_loco: DA9053 I2C SDA stuck low issue on bootupWayne Zou2011-09-06-1/+102
| | | | | | | | | | | | | | | | For DA9053 I2C SDA stuck low issue: the I2C block in DA9053 may not correctly receive a Power On Reset and device is in unknown state during start-up. The only way to get the chip into known state before any communication with the Chip via I2C is to dummy clock the I2C and bring it in a state where I2C can communicate. Dialog suggested to provide 9 clock on SCL. Dialog don't know the exact reason for the fault and assume it is because some random noise or spurious behaviour. This has to been done in host platform specific I2C driver during start-up when the I2C is being configured at platform level to supply with dummy 9 clock on SCL. Dialog I2C driver has no control to provide dummy 9 clock on SCL. Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00155283: Set dpgdck0_2_en to 0 when freq is lower than 300MHzTerry Lv2011-09-01-1/+8
| | | | | | | | 1. Set dpgdck0_2_en to 0 when required freq is lower than 300Mhz. 2. When dpgdck0_2_en is 0, the formula to calculate output freq will be changed to 2 * freq * []. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00154666-2: Align u-boot mmc command with communityTerry Lv2011-09-01-1/+1
| | | | | | Trivial change to remove build warnings. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00155472 mx53_loco: support both of RevA and RevB in ubootRobin Gong2011-08-29-4/+18
| | | | | | to fix we should amend systemrev in uboot, add new board RevB for it Signed-off-by: Robin Gong <B38343@freescale.com>
* ENGR00154672: Change to use rom plugins for mx53 boardsTerry Lv2011-08-29-79/+201
| | | | | | | | | | | | | 1. As customer required, we change to use rom plugins for mx53 boards. Tested pass with latest mfg tools. 2. Update DDR3 script based on MX53_TO2_DDR3_LCB_SMD_ARDb_v2.inc. Got from http://compass.freescale.net/livelink/livelink?func=ll &objId=221058910&objAction=browse&viewType=1. 3. Fix a tiny build error in mx53_smd.c. This error will happen when building mx53_smd_mfg. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00151255 mx53 QS: Enable VUSB_2V5Lily Zhang2011-08-22-0/+15
| | | | | | | | | Kernel stops at USB driver initialization if suspending, resuming and resetting the board. It's because VUSB_2V5 voltage is disabled after suspend. Need to re-enable it mannually into U-boot Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00155138 mx53_smd/mx53_loco: Add i2c retry to fix DA9053 i2c NAK issueWayne Zou2011-08-22-2/+10
| | | | | | | | | when board boots up, during the iMX53 SOC does DA9053 Read/Write operation, it writes slave address and wait for ACK . Instead of ACK PMIC sends NAK. A workaround fix is provided as a part of retries to fix I2C NAK for very first access. Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00151695 mx53 ddr3: update ESDREF and MR0Lily Zhang2011-07-21-3/+3
| | | | | | | | | | | Updated mx53 ddr3 script according to MX53_TO2_DDR3_LCB_SMD_ARDb_v1.inc from Michael J Kjar on July 8, 2011: -change ESDREF[REF_SEL]=01 (for 32KHz), from incorrect setting of 00 (64KHz) -change DDR3 MR0 write to "setmem /32 0x63fd901c = 0x052080b0" from "0x092080b0". This chagned write recovery from 8 clocks to 6 clocks (in line with ESDCFG1[tWR]) Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00144224: MX53: Add MMU mapping for all peripheralsTerry Lv2011-06-09-7/+16
| | | | | | | Not all peripherals are mapped in MMU. Thus we add those missed mapped area. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00144389 mx53 QS Ripley: change VCC from 1.35V to 1.3V QS Ripley boardWayne Zou2011-06-01-2/+2
| | | | | | Change VCC from 1.35V to 1.3V QS Ripley board Signed-off-by: Wayne Zou <b36644@freescale.com>
* ENGR00143302 Add mc34708 pmic support on loco/Ripley boardZou Weihua -wayne zou2011-05-20-10/+47
| | | | | | Add mc34708 pmic support on loco/Ripley board Signed-off-by: Zou Weihua -wayne zou <b36644@freescale.com>
* ENGR00143457: Don't let ROM copy .bss sectionJason Liu2011-05-16-1/+2
| | | | | | | | | | | Don't need let ROM copy the .bss section since it will all be zeroed by u-boot at start up, thus it can speed up the boot up time. Need add CONFIG_FLASH_HEADER_OFFSET to the size since ROM will copy from the beginning of the MMC card. Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00141363: change mx53 uart clk parent to pll2Jason Chen2011-03-31-3/+9
| | | | | | | | | | Change all mx53 platform uart clk default parent to pll2. MX53 SMD board need support LVDS and HDMI at the same time, they may use the same clock parent-pll4, so kernel need change ipu di clock parent to pll3, after that, uart clock parent need change to pll2 to avoid console mess. Signed-off-by: Jason Chen <b02280@freescale.com>
* ENGR00140982 MX53 Increase VDDGP to 1.25V for 1 GHzAnish Trivedi2011-03-22-2/+2
| | | | | | | | MX53 TO 2.0 requires 1.25V for VDDGP instead of 1.2V in order for the core to operate at 1 GHz. Signed-off-by: Anish Trivedi <anish@freescale.com> Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com>
* ENGR00140825: Add mx53 to2.1 chip id recognitionTerry2011-03-20-1/+4
| | | | | | Add mx53 to2.1 chip id recognition. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00139924 mx53 smd &loco: set bootup vdd GP to 1.2vZhou Jingyu2011-03-01-0/+3
| | | | | | set bootup vdd GP to 1.2v for mx53 smd &loco Signed-off-by: Zhou Jingyu <Jingyu.Zhou@freescale.com>
* ENGR00137552 MX53: increase VDDGP as 1.2V for 1GHZLily Zhang2011-01-15-2/+15
| | | | | | | | | The norminal voltage of VDDGP for 1GHZ is 1.2V in MX53 TO2.0 datasheet (RevD). So set the CPU frequency as 800MHZ firstly since VDDGP is 1.1V after power on. After increasing VDDGP as 1.2V, increase CPU as 1GHZ. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00137604: Change PLL4 to 455MHz for mx53Terry Lv2011-01-07-1/+6
| | | | | | | Required by display to set ldb. We need to set PLL4 to 455MHz. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00137642 MX53 Uboot Align DDR3 script for Loco and SMD boardsAnish Trivedi2011-01-05-2/+2
| | | | | | | | | | | | | Changed the value of one register, offset 0x88, of the ESDCTL controller to match the official script for the boards, entitled "MX53_TO2_DDR3_LCB.inc", found at http://compass.freescale.net/livelink/livelink/221435668/ MX53_TO2_DDR3_LCB.inc.txt?func=doc.Fetch&nodeid=221435668 The register value sets read delay lines. The change is minor. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00137497-2 MX53: Add LOCO board supportLily Zhang2010-12-30-0/+1202
Add MX53 LOCO board support The following functions are tested in the board: - Micro SD boot - MMC/SD read/write. - clk command - fuse command Signed-off-by: Lily Zhang <r58066@freescale.com>
generated by cgit v1.1 at 2024-11-16 01:55:51 +0000