summaryrefslogtreecommitdiff
path: root/board/freescale/mpc8360erdk
Commit message (Collapse)AuthorAgeLines
* Add wait flags to support board/chip specific delaysWolfgang Grandegger2009-03-23-1/+1
| | | | | | | | | | | | | | The NAND flash on the TQM8548_BE modules requires a short delay after running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE requires a further short delay after writing out a buffer. Normally the R/B pin should be checked, but it's not connected on the TQM8548_BE. The corresponding Linux FSL UPM driver uses similar delay points at the same locations. To manage these extra delays in a more general way, I introduced the "wait_flags" field allowing the board-specific driver to specify various types of extra delay. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* Add multi chip support to the FSL-UPM driverWolfgang Grandegger2009-03-23-1/+1
| | | | | | | | | | | This patch adds support for multi-chip NAND devices to the FSL-UPM driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now called with the argument "chip_nr" to allow testing the proper chip select line. The NAND support of the MPC8360ERDK is updated as well. No other boards are currently using the FSL UPM driver. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-18-31/+31
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Cleanup out-or-tree building for some boards (.depend)Wolfgang Denk2008-07-02-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* MPC8360ERDK: adapt NAND interface for the re-written FSL NAND UPM driverWolfgang Grandegger2008-06-19-2/+22
| | | | | | | | | This patch is based on the following patch sent a few minutes ago: "NAND FSL UPM: driver re-write using the hwcontrol callback" It is untested, of course. Anton, could you please give it a try. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* Change initdram() return type to phys_size_tBecky Bruce2008-06-12-1/+1
| | | | | | | | | | | | | | | | | | | This patch changes the return type of initdram() from long int to phys_size_t. This is required for a couple of reasons: long int limits the amount of dram to 2GB, and u-boot in general is moving over to phys_size_t to represent the size of physical memory. phys_size_t is defined as an unsigned long on almost all current platforms. This patch *only* changes the return type of the initdram function (in include/common.h, as well as in each board's implementation of initdram). It does not actually modify the code inside the function on any of the platforms; platforms which wish to support more than 2GB of DRAM will need to modify their initdram() function code. Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc MPC8641HPCN. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* mpc83xx: MPC8360E-RDK: configure pario pins for AD7843 and FHCIAnton Vorontsov2008-03-25-0/+17
| | | | | | | This patch adds qe pario pins configuration for AD7843 ADC/Touchscreen controller and FHCI (QE USB). Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* mpc83xx: MPC8360E-RDK: add support for NANDAnton Vorontsov2008-03-25-1/+75
| | | | Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* Remove erroneous or extra spd.h #includers.Jon Loeliger2008-03-05-1/+0
| | | | | | | | | | Many of the spd.h #includers don't need it, and wanted to have spd_sdram() declared instead. Since they didn't get that, some also had open coded extern declarations of it instead or as well. Fix it all up by using spd_sdram.h where needed. Signed-off-by: Jon Loeliger <jdl@freescale.com>
* mpc83xx: add support for the MPC8360E-RDKAnton Vorontsov2008-01-10-0/+418
This is MPC8360E based board with: - 256MB fixed SDRAM; - 8MB Intel Strata NOR flash; - StMICRO 64MiB NAND flash; - two 10/100/1000 ethernet ports connected via Broadcom BCM5481 PHYs; - two 10/100 ethernet ports connected via National DP83848 PHYs; - one PCI and one miniPCI slots; - four serial ports (two NS16550-compatible, two UCCs); - four USB ports working through MPC8360E "FHCI" USB controller; - Fujitsu MB86277 graphics controller; - Analog to Digital Converter/Touchscreen controller, AD7843 connected to SPI. Features not supported in this patch are: - StMICRO 64MiB NAND flash (patch sent); - MINT framebuffer initialization (patch is pending); - Fetching production information from the EEPROM via I2C; - FHCI USB; - Two slow UCCs used as RS-485 UARTs. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>