summaryrefslogtreecommitdiff
path: root/board/freescale/mpc8308rdb/mpc8308rdb.c
Commit message (Collapse)AuthorAgeLines
* fdt: Allow ft_board_setup() to report failureSimon Glass2014-11-21-1/+3
| | | | | | | | | | | | | | | | | | This function can fail if the device tree runs out of space. Rather than silently booting with an incomplete device tree, allow the failure to be detected. Unfortunately this involves changing a lot of places in the code. I have not changed behvaiour to return an error where one is not currently returned, to avoid unexpected breakage. Eventually it would be nice to allow boards to register functions to be called to update the device tree. This would avoid all the many functions to do this. However it's not clear yet if this should be done using driver model or with a linker list. This work is left for later. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* mpc8308rdb: add support for eSDHC MMC controllerIra W. Snyder2012-09-18-0/+9
| | | | | | | | | | | | | | | Add support for the onboard eSDHC MMC controller. The hardware on the MPC8308RDB has the following errata: - ESDHC111: manual asynchronous CMD12 is broken - DMA is broken (PIO works) Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> [added include fsl_esdhc header to prevent implicit declarations of fsl_esdhc_mmc_init() and fdt_fixup_esdhc()] Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc8308rdb: add support for Spansion SPI flash on header J8Ira W. Snyder2012-09-18-0/+49
| | | | | | | | | | | The SPI pins are routed to header J8 for testing SPI functionality. A Spansion flash has been wired up and tested on this header. This patch breaks support for the second TSEC interface, since the GPIO pin used as a chip select is pinmuxed with some of the TSEC pins. Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx: Remove warmboot parameter from PCI init functionsPeter Tyser2010-09-23-1/+1
| | | | | | | | | | | | | This change lays the groundwork for the BOOTFLAG_* flags being removed. This change has the small affect of delaying 100ms on PCI initialization after a warm boot as opposed to the optimal 1ms on some boards. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> included the mpc8308_p1m board. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* MPC8308RDB: various clean upsIlya Yanok2010-09-23-16/+4
| | | | | | | | | | | | | | | | | | This patch cleans up the Freescale MPC8308RDB Development board support. Things fixed: - Removed unused PCIE2 definitions from configuration - SICR{L,H} defines used for System I/O Configuration Registers values instead of hardcoding - CONFIG_SYS_SCCR_PCIEXP1CM used to enable PCIE clock instead of writing to SCCR from the board code - sleep mode stuff removed as MPC8308 has no support for deep sleep and PMCCR1 register. board_early_init_f() removed. - MPC8308 has no ERRATA for DDR controller so workaround removed - 'assignment in if statement' issues solved - use LBLAWAR_* defines instead of hardcoding Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* MPC8308RDB: minimal support for devboard from FreescaleIlya Yanok2010-07-09-0/+160
This patch provides support for MPC8308RDB development board from Freescale with a minimal set of features: Dual UART is supported NOR flash is supported Both TSEC Ethernet controllers are supported PCI Express initialization is supported The following features are enabled in configuration but not fully tested: I2C (used to get the board revision) I2C-connected RTC VSC7385 switch There is one (hopefully) minor issue: on soft reset the board sometimes resets twice. I've not managed to find the fix for this problem yet. As a workaround instruction cache can be disabled. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>