summaryrefslogtreecommitdiff
path: root/board/freescale/common/qixis.c
Commit message (Collapse)AuthorAgeLines
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-5/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* board/common: Add support for QIXIS read/write using i2cPrabhakar Kushwaha2013-01-30-0/+14
| | | | | | | | | | | | QIXIS FPGA is accessable via both i2c and flash controller. Only flash controller access is supported. Add support of i2c based access. It is quite useful in the scenario where either flash controller path is broken or not present. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/qixis: enable qixis dump command and add switch dumping commandShaveta Leekha2013-01-30-12/+35
| | | | | | | | | | | | | Remove #ifdef so that "qixis dump" command is always available Add "qixis_reset switch" command to dump switch settings Qixis doesn't have 1:1 switch mapping. We need to reverse engineer from registers to figure out switch settings. Not all bits are available. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* board/freescale/common:Add support of QTAG registerPrabhakar Kushwaha2013-01-30-0/+46
| | | | | | | | | | | | | QIXIS FPGA's QIXIS Tag Access register (QTAG) defines TAG, VER, DATE, IMAGE fields. These fields have FPGA build version, image name and build date information. Add support to parse these fields to have complete FPGA image information. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/board: add present2 register definition for QIXISShengzhou Liu2012-10-22-1/+1
| | | | | | | | According to new QIXIS system definition, update QIXIS registers set to add present2 register instead of obsolete ctl_sys2. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* board/freescale/common:QIXIS:Fix magic number usagePrabhakar Kushwaha2012-10-22-6/+7
| | | | | | | | | | | | QIXIS FPGA layout defines the address of registers but The actual register bit implementation is board-specific, So avoid use of magic numbers as it may vary across different boards's QIXIS FPGA implementation. Also, Avoid board specific defines in common/qixis.h Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/p3060qds: Add board related support for P3060QDS platformShengzhou Liu2011-11-29-0/+151
The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-11-01 06:29:39 +0000