summaryrefslogtreecommitdiff
path: root/board/digsy_mtc/digsy_mtc.c
Commit message (Collapse)AuthorAgeLines
* digsy_mtc: move board into vendor dir and add vendor logoAnatolij Gustschin2011-07-27-500/+0
| | | | Signed-off-by: Anatolij Gustschin <agust@denx.de>
* mpc5200: digsy_mtc: add support for graphic extension boardAnatolij Gustschin2011-07-27-0/+66
| | | | | | | | | | Add detection and initialisation for graphic extension board and support splash screen when booting. Enable "bmp" command in the board configuration and provide "disp" command to be able to switch the display on/off. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* Fix incorrect use of getenv() before relocationWolfgang Denk2011-05-12-3/+4
| | | | | | | | | | | | | | | | | | | A large number of boards incorrectly used getenv() in their board init code running before relocation. In some cases this caused U-Boot to hang when certain environment variables grew too long. Fix the code to use getenv_r(). Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: The LEOX team <team@leox.org> Cc: Michael Schwingen <michael@schwingen.org> Cc: Georg Schardt <schardt@team-ctech.de> Cc: Werner Pfister <Pfister_Werner@intercontrol.de> Cc: Dirk Eibach <eibach@gdsys.de> Cc: Peter De Schrijver <p2@mind.be> Cc: John Zhan <zhanz@sinovee.com> Cc: Rishi Bhattacharya <rishi@ti.com> Cc: Peter Tyser <ptyser@xes-inc.com>
* mpc52xx, digsy_mtc: protect default flash sectorsHeiko Schocher2011-04-28-0/+2
| | | | | | call flash_protect_default() to protect default sectors. Signed-off-by: Heiko Schocher <hs@denx.de>
* mpc52xx, digsy_mtc: change phy addr for rev5 boards.Heiko Schocher2011-04-28-0/+5
| | | | | | | | | | - rev5 board has phy addr 1 -> adapt CONFIG_PHY_ADDR define in board config file. - also fixup the phy addr entry in dts, before booting Linux. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* mpc52xx, digsy_mtc_rev5: Fix Linux crash, if no Flash in bank 2Heiko Schocher2011-03-21-0/+5
| | | | | | | | | | | | | | | | If no Flash is connected to cs1, Linux crashes, because reg entries are not correct adapted. Following fix is needed: - swap base addresses in CONFIG_SYS_FLASH_BANKS_LIST, as flash bank 1 is on chipselect 0 and flash bank 2 on chipselect 1 - call fdt_fixup_nor_flash_size() from ft_board_setup() Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <hs@denx.de> cc: Werner Pfister <Pfister_Werner@intercontrol.de> cc: Detlev Zundel <dzu@denx.de>
* mpc5200, digsy_mtc: add support for rev5 board versionHeiko Schocher2011-01-18-2/+107
| | | | | | | | | | | | | | | | | | | | | | | | | difference to previous board version: - M29W128GH flash from Numonyx - SDRAM ISSI IS45S16800 (Option A2 105°C) - rev5 uses RTC RV-3029-C2 - update cs0 and cs1 baseaddr and length depending on the detected flash size. - added Werner Pfister <Pfister_Werner@intercontrol.de> as maintainer for the digsy board variants - As the M29W128GH needs a special flash_cmd_reset() document that in the new file doc/README.cfi. - move "#endif /* CONFIG_CMD_IDE */" to the right place - remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5 boards - change doc/README.cfi as Stefan Roese suggested Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Detlev Zundel <dzu@denx.de> cc: Wolfgang Denk <hs@denx.de> cc: Stefan Roese <sr@denx.de> cc: Werner Pfister <Pfister_Werner@intercontrol.de> cc: Detlev Zundel <dzu@denx.de>
* ppc: Remove board-specific command table relocation fixupsPeter Tyser2009-10-03-2/+0
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* digsy MTC: Add 'mtc' command.Grzegorz Bernacki2009-06-14-0/+2
| | | | | | | | | | New command allows to: o check FW version o set LED status o set digital output status o get digital input status Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
* digsy MTC: Add SPI support.Grzegorz Bernacki2009-06-14-0/+10
| | | | Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
* Update CHANGELOG, coding style cleanup.Wolfgang Denk2009-04-05-1/+0
|
* Add support for the digsy MTC board.Grzegorz Bernacki2009-03-20-0/+307
This is the InterControl custom device based on the MPC5200B chip. Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>