summaryrefslogtreecommitdiff
path: root/board/compulab
Commit message (Collapse)AuthorAgeLines
* mx6: Use a common SPL configuration fileFabio Estevam2014-11-20-8/+0
| | | | | | | | | Many boards use a minimal .cfg file in the SPL case. Introduce spl_sd.cfg so that we can reuse it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* Merge git://git.denx.de/u-boot-tiTom Rini2014-11-07-154/+796
|\
| * omap3: cm-t3517: add LCD/DVI and splash supportIgor Grinberg2014-11-06-0/+44
| | | | | | | | | | | | | | Add support for splash screen on both DVI and SCF0403 LCD. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
| * omap3: cm-t3517: add Ethernet supportIgor Grinberg2014-11-06-0/+108
| | | | | | | | | | | | | | Add both EMAC and SMC911x support. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
| * omap3: cm-t3517: add USB supportIgor Grinberg2014-11-06-0/+120
| | | | | | | | | | | | | | | | | | Add both host and mUSB support. Currently, the selection between host USB and mUSB is done through the config file. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
| * omap3: cm-t3517: add basic board supportIgor Grinberg2014-11-06-0/+222
| | | | | | | | | | | | | | | | | | | | | | CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC. Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT, Analog audio codec, touch screen controller, LED. Add basic support including: LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
| * omap: hsmmc: assume cd gpio is active lowIgor Grinberg2014-11-06-6/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Switch the default CD GPIO polarity to active low. The current hsmmc driver assumption that the CD GPIO is active high, but in the real hardware, usually the opposite holds. The usual SD card socket has a mechanical switch which is grounded as soon as a card is inserted. Of course there might be some board logic which inverts the signal, but as far as current users are concerned, there is no such logic. Current U-Boot users either not using the CD functionality, or have a different way (e.g. external to SoC GPIO controller) for checking the card presence. This patch also brings the polarity assumption in line with the Linux kernel and adds appropriate comments. This patch also might spare issues once the TWL GPIO driver will be converted to the DM. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
| * omap3: cm-t35: move get_board_serial() fallbackIgor Grinberg2014-11-06-10/+12
| | | | | | | | | | | | | | | | | | | | The fallback is used for cases when CONFIG_SERIAL_TAG defined, but the eeprom is not used. The fallback is useful for more than one CompuLab board, so move it to a common location. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
| * omap3: cm-t35: move the SMC911x codeIgor Grinberg2014-11-06-43/+112
| | | | | | | | | | | | | | | | Extract the SMC911x initialization code to a common location where it can be reused by other compulab omap3 based boards. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
| * omap3: cm-t35: extract the splash code from boardIgor Grinberg2014-11-06-59/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The splash screen loading code can be reused by other compulab boards. For now extract it to a common location for further reuse. This also switches the splash code dependency from CONFIG_LCD to CONFIG_SPLASH_SCREEN as it should normally be. In addition this patch fixes the accidental dependency of the get_board_mem_timings() function on CONFIG_LCD, by just moving the splash code and leaving the above function intact. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
| * omap3: cm-t35: move the USB hub reset codeIgor Grinberg2014-11-06-11/+38
| | | | | | | | | | | | | | | | Extract the USB hub reset code to a common location where it can be reused by other compulab boards. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
| * compulab: refactor board revision handlingIgor Grinberg2014-11-06-25/+54
| | | | | | | | | | | | | | | | Move board revision handling code to a common location for further reuse. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-11-05-4/+5
|\ \ | |/ |/|
| * arm: mx6: cm_fx6: detect 1GB DRAM correctly on soloNikita Kiryanov2014-11-05-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | The 1GB DRAM configuration on mx6 solo uses 2 chip selects, but the code tests 1GB DRAM configuration as if it is all present on one chip select, and thus cannot see the full range of available memory. Refactor the check to detect 1GB DRAM correctly. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
| * arm: mx6: cm_fx6: change issd gpio orderNikita Kiryanov2014-11-05-1/+1
| | | | | | | | | | | | | | | | | | | | Change the order in which GPIOs are toggled in SATA init sequence to accomodate both SanDisk and Phison SSDs. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* | kconfig: arm: introduce symbol for ARM CPUsGeorges Savoundararadj2014-10-29-11/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit introduces a Kconfig symbol for each ARM CPU: CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136, CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100. Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected for CPU_ARM1176 and CPU_V7. For each target, the corresponding CPU is selected and the definition of SYS_CPU in the corresponding Kconfig file is removed. Also, it removes redundant "string" type in some Kconfig files. Signed-off-by: Georges Savoundararadj <savoundg@gmail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-imxTom Rini2014-10-27-0/+1
|\ \ | |/
| * ARM: i.MX: provide declaration for board_spi_cs_gpioEric Nelson2014-10-21-0/+1
| | | | | | | | | | | | | | | | Provide a public declaration of the board_spi_cs_gpio() callback for i.MX SPI chip selects to prevent the warning "Should it be static?" when compiling with "make C=1". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-tiTom Rini2014-10-27-15/+4
|\ \
| * | omap3/am33xx: mux: fix several checkpatch issuesIgor Grinberg2014-10-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the following checkpatch issues: CHECK: No space is necessary after a cast \#39: FILE: arch/arm/include/asm/arch-am33xx/mux.h:39: +#define PAD_CTRL_BASE 0x800 +#define OFFSET(x) (unsigned int) (&((struct pad_signals *) \ CHECK: Avoid CamelCase: <CONTROL_PADCONF_JTAG_nTRST> \#284: FILE: arch/arm/include/asm/arch-omap3/mux.h:284: +#define CONTROL_PADCONF_JTAG_nTRST 0x0A1C ERROR: space required after that ',' (ctx:VxV) \#446: FILE: arch/arm/include/asm/arch-omap3/mux.h:446: +#define MUX_VAL(OFFSET,VALUE)\ ^ Cc: Raphael Assenat <raph@8d.com> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Nishanth Menon <nm@ti.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefan Roese <sr@denx.de>
| * | omap3: cm-t35: remove enable_gpmc_cs_config()Igor Grinberg2014-10-23-13/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The gpmc_init() function already calls enable_gpmc_cs_config() for chip select 0. Although the bus width is configured for 16 bit, it gets reconfigured correctly in the omap_gpmc driver later. Remove the enable_gpmc_cs_config() function call and the associated gpmc_nand_config[] array. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
| * | omap3: cm-t35: use define for mmc wp gpioIgor Grinberg2014-10-23-1/+3
| | | | | | | | | | | | | | | | | | Switch to using define for MMC WP GPIO instead of a magic number. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* | | dm: move platform data headers to include/dm/platform_dataMasahiro Yamada2014-10-23-1/+1
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The platform_data definitions are generally referenced from both drivers and board files. That is why header files defining platform_data sturectures are placed in "include" directory, but our top level "include" directory is already too cluttered. Let's collect platform_data definitions under the directory "include/dm/platform_data" like Linux gathers ones around under "include/linux/platform_data". This commit moves two header files: include/serial_mxc.h -> include/dm/platform_data/serial_mxc.h include/serial_pl01x.h -> include/dm/platform_data/serial_pl01x.h Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | dm: imx: Move cm_fx6 to use driver model for serial and GPIOSimon Glass2014-10-22-0/+10
| | | | | | | | | | | | | | | | | | Now that serial and GPIO are available for iMX.6, move cm_fx6 over as an example. Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
* | arm: mx6: cm_fx6: use gpio requestNikita Kiryanov2014-10-22-39/+94
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use gpio_request for all the gpios that are utilized by various subsystems in cm-fx6, and refactor the relevant init functions so that all gpios are requested during board_init(), not during subsystem init, thus avoiding the need to manage gpio ownership each time a subsystem is initialized. The new division of labor is: During board_init() muxes are setup and gpios are requested. During subsystem init gpios are toggled. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* | imx: Add error checking to setup_i2c()Simon Glass2014-10-22-6/+34
|/ | | | | | | Since this function can fail, check its return value. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
* compulab: eeprom: add default eeprom busNikita Kiryanov2014-10-09-0/+4
| | | | | | | | | | | Add default eeprom bus setting. This addresses the trimslice compile error that was introduced with the addition of this setting. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-09-17-1/+1031
|\
| * arm: mx6: cm_fx6: add sata supportNikita Kiryanov2014-09-09-0/+100
| | | | | | | | | | | | | | | | | | Add support for SATA. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
| * arm: mx6: cm_fx6: use eepromNikita Kiryanov2014-09-09-0/+30
| | | | | | | | | | | | | | | | | | | | Use Compulab eeprom module to obtain revision number, serial number, and mac address from the EEPROM. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
| * arm: mx6: cm_fx6: add i2c supportNikita Kiryanov2014-09-09-0/+42
| | | | | | | | | | | | | | | | | | | | Add support for all 3 I2C busses on Compulab CM-FX6 CoM. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
| * arm: mx6: cm_fx6: add usb supportNikita Kiryanov2014-09-09-0/+79
| | | | | | | | | | | | | | | | | | Add USB and USB OTG host support for Compulab CM-FX6 CoM. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
| * arm: mx6: cm_fx6: add ethernet supportNikita Kiryanov2014-09-09-0/+101
| | | | | | | | | | | | | | | | | | | | Add ethernet support for Compulab CM-FX6 CoM Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
| * arm: mx6: cm_fx6: add nand supportNikita Kiryanov2014-09-09-0/+48
| | | | | | | | | | | | | | | | | | | | Add NAND support for Compulab CM-FX6 CoM. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
| * arm: mx6: add support for Compulab cm-fx6 CoMNikita Kiryanov2014-09-09-0/+619
| | | | | | | | | | | | | | | | | | | | | | | | | | Add initial support for Compulab CM-FX6 CoM. Support includes MMC, SPI flash, and SPL with dynamic DRAM detection. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
| * compulab: eeprom: add support for defining eeprom i2c busNikita Kiryanov2014-09-09-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Create CONFIG_SYS_I2C_EEPROM_BUS #define to tell the EEPROM module what I2C bus the EEPROM is located at. Make cl_eeprom_read() switch to that bus when reading EEPROM. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: Tom Rini <trini@ti.com> Cc: Marek Vasut <marex@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* | kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-13-14/+0
|/ | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* omap5: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-8/+0
| | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the OMAP5 board select menu to omap5/Kconfig. Move also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="omap5"). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com>
* omap3: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-8/+0
| | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the OMAP3 board select menu to omap3/Kconfig. Move also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="omap3 Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Tom Rini <trini@ti.com>
* tegra: kconfig: move board select menu and common settingsMasahiro Yamada2014-08-30-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | Becuase the board select menu in arch/arm/Kconfig is too big, move the Tegra board select menu to tegra/Kconfig. Insert the Tegra SoC select menu between the arch select and the board select. Architecture select |-- Tegra Platform (Tegra) |- Tegra SoC select (Tegra20 / 30 / 114 / 124) |- Board select Consolidate also common settings (CONFIG_SYS_CPU="armv7" and CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows: config TEGRA bool select SPL Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com>
* cm-t54: fix eMMC boot mode checkDmitry Lifshitz2014-08-25-1/+1
| | | | | | | | | | Boot from eMMC boot partition corresponds to BOOT_DEVICE_MMC2 omap_bootmode, while BOOT_DEVICE_MMC2_2 corresponds to the user data partition boot. Fix mmc_get_env_part() boot mode check to use a correct value. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
* cm-t54: fix EEPROM read return value checkDmitry Lifshitz2014-08-25-2/+2
| | | | | | | Fix cl_eeprom_read_mac_addr() return value check. Fix long line codding style issue in board_init(). Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
* Add board MAINTAINERS filesMasahiro Yamada2014-07-30-0/+25
| | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-30-0/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* cm_t335: Fix the U-Boot binary outputSimon Glass2014-06-11-2/+2
| | | | | | | Correct the binary output so that image_binary_size is really at the end of the image. Signed-off-by: Simon Glass <sjg@chromium.org>
* omap3: remove remnant macros GPMC_NAND_ECC_LP_x8_LAYOUT and ↵pekon gupta2014-06-06-6/+6
| | | | | | | | | | | GPMC_NAND_ECC_LP_x16_LAYOUT OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros to configure GPMC controller for x7 or x8 bit device connected to its interface. Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above macros can be completely removed. Signed-off-by: Pekon Gupta <pekon@ti.com>
* compulab: eeprom: enable any i2c driverIlya Ledvich2014-05-23-2/+2
| | | | | | | Make the common eeprom library available for any I2C driver. Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t54: add environment partition runtime detectionDmitry Lifshitz2014-05-23-0/+22
| | | | | | | Add environment partition runtime detection callback. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t54: add EEPROM support and MAC address handlingDmitry Lifshitz2014-05-23-0/+63
| | | | | | | | | | | | | cm-t54 Eth MAC address is stored in onboard EEPROM. Add EEPROM support and setup stored Eth MAC address. If EEPROM does not contain a valid MAC, then generate it from the processor ID code (reference code is taken from OMAP5 uEvm board file). Modify Device Tree blob MAC address field with retrieved data. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* cm-t54: add cm-t54 board supportDmitry Lifshitz2014-05-23-0/+347
| | | | | | | | | | | | | | | Add cm-t54 board directory, config file. Enable build. Basic support includes: Serial console SD/MMC eMMC USB Ethernet Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
generated by cgit v1.1 at 2024-11-09 22:25:26 +0000