arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	board: atmel: clean up the PMC_PLLICPR init code	Wenyou Yang	2016-02-18	-3/+1
\| \| \| \| \| \| \| \| \|	Due to introducing the PMC_PLLICPR init function, use this function to clean up the code. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
*	board: atmel: clean up peripheral clock code	Wenyou Yang	2016-02-18	-3/+2
\| \| \| \| \| \| \| \| \| \|	Due to introducing the new peripheral clock handle functions, use these functions to reduce duplicated code. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Heiko Schocher <hs@denx.de> [Rebased on current master, fixup for at91rm9200ek] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
*	arm: at91/spl: mpddrc: add struct atmel_mpddrc_config	Wenyou Yang	2016-02-02	-2/+2
\| \| \| \| \| \| \| \| \| \|	Add struct atmel_mpddrc_config to accommodate the mpddrc register configurations, not using the mpddrc register map structure, struct atmel_mpddrc, in order to increase readability and reduce run-time memory use. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
*	arm: at91: pmc: replace the constant with a define in at91_pmc.h	Erik van Luijk	2015-08-21	-1/+1
\| \| \| \| \| \| \| \|	To enable the clocks on the at91 boards a constant (0x4) is used. This is replaced with a define in at91_pmc.h (1 << 2). Signed-off-by: Erik van Luijk <evanluijk@interact.nl> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
*	arm: at91: mpddr: allow multiple DDR controllers	Erik van Luijk	2015-08-21	-1/+1
\| \| \| \| \| \| \| \| \|	The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller. This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10). Signed-off-by: Erik van Luijk <evanluijk@interact.nl> [remove 'new blank line at EOF'] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
*	ARM: atmel: enable SPL on sama5d3_xplained board	Bo Shen	2014-05-27	-0/+87
\| \| \| \| \| \| \|	It supports boot from NAND and SD/MMC card. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
*	ARM: atmel: add sama5d3 Xplained board support	Bo Shen	2014-03-09	-0/+130
	Add sama5d3 Xplained board support which use Atmel SAMA5D36 SoC. Now it supports boot from NAND flash and SD/MMC card. Features support: - NAND flash - SD/MMC card - Two USB hosts - Ethernet (one GMAC, one EMAC) Signed-off-by: Bo Shen <voice.shen@atmel.com> [reorder boards.cfg] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>