summaryrefslogtreecommitdiff
path: root/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
Commit message (Collapse)AuthorAgeLines
* nand: Embed mtd_info in struct nand_chipScott Wood2016-06-03-1/+1
| | | | | | | | | | | | nand_info[] is now an array of pointers, with the actual mtd_info instance embedded in struct nand_chip. This is in preparation for syncing the NAND code with Linux 4.6, which makes the same change to struct nand_chip. It's in a separate commit due to the large amount of changes required to accommodate the change to nand_info[]. Signed-off-by: Scott Wood <oss@buserror.net>
* board: atmel: clean up peripheral clock codeWenyou Yang2016-02-18-15/+5
| | | | | | | | | | Due to introducing the new peripheral clock handle functions, use these functions to reduce duplicated code. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Heiko Schocher <hs@denx.de> [Rebased on current master, fixup for at91rm9200ek] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91/spl: mpddrc: add struct atmel_mpddrc_configWenyou Yang2016-02-02-2/+2
| | | | | | | | | | Add struct atmel_mpddrc_config to accommodate the mpddrc register configurations, not using the mpddrc register map structure, struct atmel_mpddrc, in order to increase readability and reduce run-time memory use. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91: pmc: replace the constant with a define in at91_pmc.hErik van Luijk2015-08-21-1/+1
| | | | | | | | To enable the clocks on the at91 boards a constant (0x4) is used. This is replaced with a define in at91_pmc.h (1 << 2). Signed-off-by: Erik van Luijk <evanluijk@interact.nl> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91: at91sam9m10g45ek/corvus remove useless chip select 1 initErik van Luijk2015-08-21-8/+0
| | | | | | | | On these boards the DDR is connected to a dedicated controller and not to chip select 1 of the EBI. Signed-off-by: Erik van Luijk <evanluijk@interact.nl> Tested-by: Erik van Luijk <evanluijk@interact.nl>
* arm: at91: mpddr: allow multiple DDR controllersErik van Luijk2015-08-21-1/+1
| | | | | | | | | The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller. This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10). Signed-off-by: Erik van Luijk <evanluijk@interact.nl> [remove 'new blank line at EOF'] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* ARM: atmel: at91sam9m10g45ek: enable spl supportBo Shen2015-04-01-0/+80
| | | | | | | | | | | Supports boot up from NAND flash with software ECC eanbled. And supports boot up from SD/MMC card with FAT file system. As the boot from SD/MMC card with FAT file system, the BSS segment is too big to fit into SRAM, so, use the lds to put it into SDRAM. Signed-off-by: Bo Shen <voice.shen@atmel.com>
* cosmetic: atmel: replace old style struct initJeroen Hofstee2014-06-11-14/+14
| | | | | | This prevents some warnings when building with clang. cc:: andreas.devel@googlemail.com Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* ARM: at91sam9m10g45ek: enable mci0 supportWu, Josh2014-05-27-0/+10
| | | | | | | | | | Also we enable the mmc command in configuration file. As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION, so remove the redundant CONFIG_DOS_PARTITION definition. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm926ejs, at91: add common phy_reset functionHeiko Schocher2013-12-01-18/+1
| | | | | | | | | | | | | | | | | | | add common phy reset code into a common function. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com> Cc: Jens Scharsig <esw@bus-elektronik.de> Cc: Sergey Lapin <slapin@ossfans.org> Cc: Stelian Pop <stelian@popies.net> Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> Cc: Eric Benard <eric@eukrea.com> Cc: Markus Hubig <mhubig@imko.de> Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Tested-by: Bo Shen <voice.shen@atmel.com> Acked-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* arm:at91-boards: remove console_init_f where unnecessaryAndreas Bießmann2012-09-01-3/+0
| | | | | | | | | | | | | | | | A lot of at91 boards have the console_init_f in board_init. This is useless cause it was called before by generic code in lib/board.c. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> cc: Jens Scharsig <esw@bus-elektronik.de> cc: Stelian Pop <stelian@popies.net> cc: Sedji Gaouaou<sedji.gaouaou@atmel.com> cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> cc: Eric Benard <eric@eukrea.com> Tested-by: voice.shen@atmel.com Tested-by: voice.shen@atmel.com Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
* Fix Stelian's email addressStelian Pop2011-11-29-1/+1
| | | | | | | Change my old email address which is no longer valid. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Anatolij Gustschin <agust@denx.de>
* atmel: Update support of board AT91SAM9M10G45-EK to new styleThomas Petazzoni2011-09-03-52/+63
| | | | | | Based on earlier work by Alex Waterman <awaterman@dawning.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
* Write MAC address automatically on MACB-based boardsBen Warren2010-07-12-7/+0
| | | | | | Also, remove all calls to eth_init() in boards that use MACB Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* USB OHCI support for at91sam9g45 SoCSergey Matyukevich2010-06-30-0/+13
| | | | | | | | | | Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards. Note that according to errata from Atmel, OHCI is not operational on the first revision of at91sam9g45 chip. So this patch enables OHCI support for later revisions. Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
* ARM change name of defines for AT91 arm926ejsAchim Ehrlich2010-03-07-1/+1
| | | | | | | | | | Configuration defines should be preceeded with CONFIG_SYS_. Renamed some at91 specific defines to conform to this naming convention: AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
* at91: Introduction of at91sam9g45 SOC.Sedji Gaouaou2009-07-12-0/+334
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz. It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of peripherals. The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. On the board you can find 2 USART, USB high speed, a 480*272 LG lcd, ethernet, gpio/joystick/buttons. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>