summaryrefslogtreecommitdiff
path: root/arch
Commit message (Collapse)AuthorAgeLines
* arm: mxs: Add 'Wait for JTAG user' if booted in JTAG modeGraeme Russ2015-02-10-0/+22
| | | | | | | | | | | When booting in JTAG mode, there is no way to use soft break-points, and no way of knowing when SPL has finished executing (so the user can issue a 'halt' command to load u-boot.bin for example) Add a debug output and simple loop to stop execution at the completion of the SPL initialisation as a pseudo break-point when booting in JTAG mode Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
* arm: mxs: Enable booting of mx28 without batteryGraeme Russ2015-02-10-2/+8
| | | | | | | | | | | | | | | | | | Section 4.1.2 of Freescale Application Note AN4199 describes the configuration required to operate the mx28 from a 5V source without a battery. This patch changes the behaviour of the dropout control of the DC-DC converter (refer to section 11.12.9 of the mx28 Application Processor Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the following: - Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined - Switch between 4P2 Linear Regulator and Battery, using whichever has the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is the same as the pre-patch behaviour) Signed-off-by: Graeme Russ <gruss@tss-engineering.com> Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
* arm: mxs: Add debug outputs and comments to mxs SPL source filesGraeme Russ2015-02-10-5/+127
| | | | | | | | | | | | | It is difficult to track down fail to boot issues in the mxs SPL. Implement the following to make it easier: - Add debug outputs to allow tracing of SPL progress in order to track where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must be defined to enable debug output in SPL - Add TODO comments where it is not clear if the code is doing what it is meant to be doing, even tough the board boots properly (these comments refer to existing code, not to any code added by this patch) Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
* imx: mx6: Fixed AIPS3 base address issueYe.Li2015-02-10-3/+3
| | | | | | | | | Should use AIPS3 configuration address 0x0227C000 to set AIPS3, not the AIPS3 base address. Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem. Signed-off-by: Ye.Li <B37916@freescale.com>
* imx:mx6 update fuse_bank0_regsPeng Fan2015-02-10-4/+8
| | | | | | Update fuse_bank0_regs structure according reference mannual. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* ot1200: select SUPPORT_SPLChristian Gmeiner2015-01-22-0/+1
| | | | Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
* imx:mx6sx add dram io configure for mx6sxPeng Fan2015-01-22-14/+128
| | | | | | | | | | | Define two structure mx6sx_iomux_ddr_regs and mx6sx_iomux_grp_regs. Add a new function mx6sx_dram_iocfg to configure dram io. Since mx6sx only have one channel mmdc0, define a new empty macro MMDC1 to replace mmdc1->entry=value for mx6sx. And to other mx6 soc, MMDC1 effects as "mmdc1->entry=value". Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* imx:mx6sxsabresd select SUPPORT_SPLPeng Fan2015-01-22-0/+1
| | | | | | select SUPPORT_SPL for mx6sxsabresd. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* arm: mx6: Add Barco platinum-picon and platinum-titaniumStefan Roese2015-01-19-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the new Barco platinum platform. It currently includes those two boards: platinum-titanium ----------------- This is the same board as the titanium that is already supported in mainline U-Boot. But its now moved to this new platform to support multiple "flavors" of imx6 boards in one directory. Its also moved to support SPL booting. And with this we use the run-time DDR configuration of this SPL support. The board is equipped with the Micron MT41J128M16JT-125 DDR chips. We now can remove the DDR related registers tuples from the imximage.cfg file. As all this is done in the SPL at run-time. platinum-picon -------------- This board is new and based on the MX6DL with 1GiB DDR using the Micron MT41K256M16HA DDR3 chips. Its also equipped with 2 NAND chips (each 512MiB). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Pieter Ronsijn <pieter.ronsijn@barco.com>
* Merge branch 'master' of git://git.denx.de/u-boot-tiTom Rini2015-01-16-51/+138
|\
| * arm: am437x: Enable hardware leveling for EMIFJames Doublesin2015-01-13-51/+138
| | | | | | | | | | | | | | | | | | | | | | | | Switch to using hardware leveling for certain parameters on the EMIF rather than using precalculated values. Doing this also means we have a common place now between am437x and am335x for setting emif_sdram_ref_ctrl with a value for the correct delay length. Tested-by: Felipe Balbi <balbi@ti.com> Tested-by: Tom Rini <trini@ti.com> Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
* | powerpc: 74xx_7xx: remove 74xx_7xx cpu supportMasahiro Yamada2015-01-16-2362/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | All the 74xx_7xx boards are still non-generic boards: P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2 Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefan Roese <sr@denx.de> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Nye Liu <nyet@zumanetworks.com> Cc: Roy Zang <tie-fei.zang@freescale.com>
* | mpc8xx: remove unused linker scriptMasahiro Yamada2015-01-16-82/+0
| | | | | | | | | | | | | | | | | | | | Now TQM8xx is the only remaining board family of mpc8xx. It uses its own linker script, board/tqc/tqm8xx/u-boot.lds. arch/powerpc/cpu/mpc8xx/u-boot.lds is not used by any boards. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de>
* | ppc4xx: remove dead codeMasahiro Yamada2015-01-16-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | Since commit 843125daebd7 (ppc4xx: remove HH405 board), CONFIG_HH405 is not defined. Since commit d52633047913 (ppc4xx: remove PMC405), CONFIG_PMC405 is not defined. Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
* | ARM: armv8: Fix typo in commentaryMichal Simek2015-01-14-1/+1
| | | | | | | | Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | Add support for Seagate BlackArmor NAS220Evgeni Dobrev2015-01-14-0/+4
| | | | | | | | | | | | Add support for Seagate BlackArmor NAS220 Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
* | sunxi: usbc: Add support for usb-vbus0 controller by axp drivebus pinHans de Goede2015-01-14-0/+26
| | | | | | | | | | | | | | | | | | The axp221 / axp223's N_VBUSEN pin can be configured as an output rather then an input, and this is used on some boards to control usb-vbus0, add support for this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: usbc: Add support for usb0 to the common usbc codeHans de Goede2015-01-14-9/+30
| | | | | | | | | | Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: Move usb-controller init code out of ehci-sunxi.c for reuse for otgHans de Goede2015-01-14-3/+254
| | | | | | | | | | | | | | | | | | | | Most of the usb-controller init code found in ehci-sunxi.c also is necessary to init the otg usb controller, so move it to a common place. While at it also update various #ifdefs / defines for sun8i support. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sun7i: Move psci_arch_init close to text_endJan Kiszka2015-01-14-40/+40
| | | | | | | | | | | | | | | | | | "adr rX, text_end" only works if the label is close. Adding further code to the other functions will prevent this. So move the containing function close to label. No functional change. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sun7i: Add support for taking CPUs offline via PSCIJan Kiszka2015-01-14-0/+171
| | | | | | | | | | | | | | | | | | | | | | Based on the original version by Marc Zyngier. It adds a psci_cpu_off implementation for the A20 SoC. The mechanism works by first preparing the calling CPU to go offline (disable and flush cache, disable SMP), then requesting CPU 0 to pull the plug. The request is sent as FIQ on SGI15. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: video: Add lvds supportHans de Goede2015-01-14-0/+15
| | | | | | | | | | | | | | Add support for lvds lcd panels Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
* | sunxi: video: Add VGA output supportHans de Goede2015-01-14-0/+78
| | | | | | | | | | | | | | Add support for VGA directly from the sunxi SoC / display engine. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: video: Add lcd output supportHans de Goede2015-01-14-6/+26
| | | | | | | | | | | | | | | | Add lcd output support, see the new Kconfig entries and doc/README.video for how to enable / configure this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: video: Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1Hans de Goede2015-01-14-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a preparation patch for adding lcd support. While at it also swap the divider search order, searching from low to high, as the comment above the code says we should do. In cases where there are multiple solutions this will result in picking a lower pll clock and divider, which is more stable and saves power. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: gpio: Add support for gpio pins on the AXP209 pmicHans de Goede2015-01-14-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino board, which uses gpio0 of the axp209 for the lcd-power signal. This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c changes are universal, adding gpio support for the other AXP pmics (when necessary) should be a matter of adding the necessary axp_gpio_foo functions to their resp. drivers, and add "#define AXP_GPIO" to their header file. Note this commit only adds support for the non device-model version of the gpio code, patches for adding support to the device-model version are very welcome. The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix is there in case we need to support gpio-s on more then 1 pmic in the future. At least A80 boards have 2 pmics, and we may end up needing to support gpio-s on both. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: gpio: Properly sort mux defines by port numberHans de Goede2015-01-14-5/+5
| | | | | | | | | | | | | | | | Move a few mux defines around so that all the mux defines are properly sorted by port number. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: video: Set input sync enableHans de Goede2015-01-14-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a write to the "unknown" (*) register to enable auto input sync, when initially adding sunxi hdmi output support this magic write from the android kernel code was missed, causing lcdc -> hdmi encoder sync problems. With this write added, we can drop the modesetting retries and the extra delays added to work around these sync problems. With the retries dropped there also is no need to 0 all the enable flags at the beginning of the modeset, as they are initialized to 0 already by engines_init. *) "unknown" is the actual name of this register in the android kernel sources Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | sunxi: video: Add hdmi supportHans de Goede2015-01-14-10/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So far we've been programming the hdmi-encoder to send out dvi data over the hdmi connector. This works well for most devices, including hdmi devices, but not all devices accept dvi data on a hdmi input. Add support for sending proper hdmi data over the hdmi output found on most sunxi boards. This can be turned on by adding monitor=hdmi as option to the video-mode env. variable. A follow up patch will determine whether to send dvi or hdmi automatically when EDID is used. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | sunxi: video: Add DDC & EDID supportHans de Goede2015-01-14-0/+85
| | | | | | | | | | | | | | | | | | | | Add DDC & EDID support and use it to automatically select the native mode of the attached monitor. This can be disabled by adding edid=0 as option to the video-mode env. variable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* | sunxi: Fix PLL1 running at half speed on sun8iHans de Goede2015-01-14-3/+7
| | | | | | | | | | | | | | | | | | | | PLL1 on sun6i / sun8i also has a p factor which divides the clock by 2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is used and we were setting it to 1, resulting in the CPU running at 504 MHz instead of 1008 MHz, this commit fixes this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: Fix buggy sun6i/sun8i DRAM size detection logicSiarhei Siamashka2015-01-14-18/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After reboot, reset or even short power off, DRAM typically retains the old stale data for some period of time (for this type of memory, the bits of data are stored in slowly discharging capacitors). The current sun6i/sun8i DRAM size detection logic, which is inherited from the Allwinner code, relies on using a large magic signature with the hope that it is unique enough and unlikely to ever accidentally match this leftover garbage data in RAM. But this approach is inherently unsafe, as can be demonstrated using the following test program: /***** A testcase for reproducing the problem ******/ void main(int argc, char *argv[]) { size_t size, i; uint32_t *buf; /* Allocate the buffer */ if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) || !(buf = malloc(size))) { printf("Need buffer size in MiB as a cmdline argument\n"); exit(1); } /* Fill it with the Allwinner DRAM "magic" values */ for (i = 0; i < size / 4; i++) buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64; /* Try to reboot */ system("reboot"); /* And wait */ for (;;) {} } /***************************************************/ If this test program is run on the device (giving it a large chunk of memory), then the DRAM size detection logic in u-boot gets confused after reboot and fails to initialize DRAM properly. A better approach is not to rely on luck and abstain from making any assumptions about the properties of the leftover garbage data in RAM. Instead just use a more reliable code for testing whether two different addresses refer to the same memory location. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | sun8i: Add dram initialization supportHans de Goede2015-01-14-1/+621
| | | | | | | | | | | | | | | | Based on the register / dram_para headers from the Allwinner u-boot / linux sources + the init sequences from boot0. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: Use memcmp for mctl_mem_matchesHans de Goede2015-01-14-9/+3
| | | | | | | | | | | | | | Use memcmp for mctl_mem_matches instead of DIY. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: Fill memory before comparing it when doing dram init on sun6iHans de Goede2015-01-14-14/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The sun8i boot0 code fills the DRAM with a "random" pattern before comparing it at different offsets to do columns, etc. detection. The sun6i boot0 code does not do it, instead relying on the memory contents being random enough to begin with for the memcmp to properly detect the wrap-around address, iow it is working purely by chance. Since our sun6i dram code was modelled after the boot0 code it contained the same issue. This commit fixes this by filling the memory with a unique, distinct pattern. The new mctl_mem_fill function this introduces is added as an inline helper in dram.h, so that it can be shared with the sun8i dram code. While at it move mctl_mem_matches to dram.h for re-use in sun8i too. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: Move await_completion dram helper to dram.hHans de Goede2015-01-14-37/+25
| | | | | | | | | | | | | | | | | | The await_completion helper is already copy pasted between the sun4i and sun6i dram code, and we need it for sun8i too, so lets make it an inline helper in dram.h, rather then adding yet another copy. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sun6i: clock_set_pll5: Calculate k and m rather then hardcoding themHans de Goede2015-01-14-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Our old hardcoded k and m values are based on PLL5 being configured in steps of 48 MHz, which is correct for sun6i where the DRAM PLL runs at twice the DRAM CLK, which is usually configured in 24 MHz step. But on the A23 (sun8i) the PLL5 runs at half the DRAM CLK, so we require 12 MHz steps. This commit adjusts clock_set_pll5 to automatically select the best k and m depending on the requested clk rate. Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sun6i: Add a sigma_delta_enable paramter to clock_set_pll5()Hans de Goede2015-01-14-4/+13
| | | | | | | | | | | | | | | | The sun8i dram code sometimes wants to enable sigma delta mode, add a parameter to allow this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: axp221: Add axp223 supportHans de Goede2015-01-14-1/+1
| | | | | | | | | | | | | | | | | | The axp223 appears to be the same as the axp221, except that it uses the rsb to communicate rather then the p2wi. At least all the registers we use are 100% the same. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: Add support for the rsb (Reduced Serial Bus)Hans de Goede2015-01-14-1/+219
| | | | | | | | | | | | | | | | | | | | | | | | sun8i (A23) introduces a new bus for communicating with the pmic, the rsb, the rsb is also used to communicate with the pmic on the A80, and is documented in the A80 user manual. This commit adds support for this based on the rsb driver from the allwinner u-boot sources. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sun6i: s/SUNXI_*P2WI*/SUN6I_*P2WI*/Hans de Goede2015-01-14-10/+10
| | | | | | | | | | | | | | | | The p2wi interface is only available on sun6i, adjust the gpio pinmux and base address defines for it to reflect this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: Align PSCI stack calculation to commentJan Kiszka2015-01-14-1/+1
| | | | | | | | | | | | | | | | 0x400 is true 1K. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: Add sunxi_get_sid helper functionHans de Goede2015-01-14-0/+20
| | | | | | | | | | | | | | | | | | | | On sun6i the SID is stored in the pmic, rather then in the SoC itself, add a helper function to abstract this away. This makes our MAC address generation code also work on sun6i. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sunxi: mmc: Properly setup mod-clk and clock sampling phasesHans de Goede2015-01-14-9/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The sunxi mmc controller has both an internal clock divider, as well as the divider in the mod0-clk for the mmc controller. The internal divider cannot be used, as it conflicts with the setting of clock sampling phases which is done in the mod0-clk, so it must be set to 0 (divide by 1). For some reason while the kernel has had this correct from day one, the u-boot sunxi mmc code has been using a fixed mod0-clk and setting its internal divider depending on the desired speed. This is something which we've inherited from the original Allwinner u-boot sources, but while this has been fixed in Allwinner's own u-boot code at least for the A23 and later upstream u-boot was still doing this wrong. This commit fixes this, thereby also fixing mmc support not working reliable on the A23 (which seems more sensitive to this) and possible also fixes some other sunxi mmc issues. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sun6i: dram: Do not try to initialize a second dram chan on A31sHans de Goede2015-01-14-7/+15
| | | | | | | | | | | | | | | | The A31s only has one dram channel, so do not bother with trying to initialize a second channel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sun6i: Add sunxi_get_ss_bonding_id() functionHans de Goede2015-01-14-2/+45
| | | | | | | | | | | | | | | | Add a sunxi_get_ss_bonding_id() function, and use it to differentiate between the A31s and the A31. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | sun6i: Make dram clk and zq value Kconfig optionsHans de Goede2015-01-14-7/+5
| | | | | | | | | | | | | | | | | | | | | | | | It turns out that there is a too large spread between boards to handle this with a default value, turn this into Kconfig options, and set the values the factory images are using for the Colombus and Mele_M9 boards. Note this changes the ZQ default when not overriden through defconfig from 120 to 123, as that is what most boards seem to actually use. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | Merge git://git.denx.de/u-boot-x86Tom Rini2015-01-13-583/+980
|\ \
| * | x86: coreboot: Configure pci memory regionsBin Meng2015-01-13-2/+28
| | | | | | | | | | | | | | | | | | | | | | | | Configure coreboot pci memory regions so that pci device drivers could work correctly. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
| * | x86: Make chromebook_link the default board for corebootBin Meng2015-01-13-219/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE to chromebook_link which is currently the only real board officially supported to run U-Boot loaded by coreboot. Note the symbolic link file chromebook_link.dts is deleted and link.dts is renamed to chromebook_link.dts. To avoid multiple definition of video_hw_init, the CONFIG_VIDEO_X86 define needs to be moved to arch/x86/cpu/ivybridge/Kconfig. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-12-26 19:21:21 +0000