summaryrefslogtreecommitdiff
path: root/arch
Commit message (Collapse)AuthorAgeLines
* socfpga: Adding DesignWare watchdog supportChin Liang See2014-07-05-0/+1
| | | | | | | | | | | To enable the DesignWare watchdog support at SOCFPGA Cyclone V dev kit. Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
* arm: ep9315: Return back Cirrus Logic EDB9315A board supportSergey Kostanbaev2014-07-04-27/+521
| | | | | | | This patch returns back support for old ep93xx processors family Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com> Cc: albert.u.boot@aribaud.net
* ARM: cache_v7: use __weakJeroen Hofstee2014-07-04-55/+15
| | | | | | | | | | This is not only more readable but also prevents a warning about a missing prototype. The prototypes which are actually missing are added. cc: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Tom Rini <trini@ti.com>
* ARMv8/ls2085a_emu: Add LS2085A emulator and simulator board supportYork Sun2014-07-04-2/+2
| | | | | | | | | | | | | | | | LS2085A is an ARMv8 implementation. This adds board support for emulator and simulator: Two DDR controllers UART2 is used as the console IFC timing is tightened for speedy booting Support DDR3 and DDR4 as separated targets Management Complex (MC) is enabled Support for GIC 500 (based on GICv3 arch) Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Arnab Basu <arnab.basu@freescale.com> Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
* armv8/fsl-lsch3: Add support to load and start MC FirmwareJ. German Rivera2014-07-03-0/+11
| | | | | | | | | | | | | | | | Adding support to load and start the Layerscape Management Complex (MC) firmware. First, the MC GCR register is set to 0 to reset all cores. MC firmware and DPL images are copied from their location in NOR flash to DDR. MC registers are updated with the location of these images. Deasserting the reset bit of MC GCR register releases core 0 to run. Core 1 will be released by MC firmware. Stop bits are not touched for this step. U-boot waits for MC until it boots up. In case of a failure, device tree is updated accordingly. The MC firmware image uses FIT format. Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com> Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
* ARMv8/FSL_LSCH3: Add FSL_LSCH3 SoCYork Sun2014-07-03-1/+937
| | | | | | | | | | | | | | Freescale LayerScape with Chassis Generation 3 is a set of SoCs with ARMv8 cores and 3rd generation of Chassis. We use different MMU setup to support memory map and cache attribute for these SoCs. MMU and cache are enabled very early to bootst performance, especially for early development on emulators. After u-boot relocates to DDR, a new MMU table with QBMan cache access is created in DDR. SMMU pagesize is set in SMMU_sACR register. Both DDR3 and DDR4 are supported. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com> Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
* ARMv8: Adjust MMU setupYork Sun2014-07-03-30/+44
| | | | | | | Make MMU function reusable. Platform code can setup its own MMU tables. Signed-off-by: York Sun <yorksun@freescale.com> CC: David Feng <fenghua@phytium.com.cn>
* Added 64-bit MMIO accessors for ARMv8J. German Rivera2014-07-03-0/+8
| | | | | | | This is needed for accessing peripherals with 64-bit MMIO registers, from ARMv8 processors. Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
* arm: Add support for semihosting for armv8 fastmodel targets.Darwin Rambo2014-07-03-0/+255
| | | | | | | | | | | | | | | | | | | | | | The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF images and u-boot, and does this for virtual platforms by using semihosting. This commit extends this idea by allowing u-boot to also use semihosting to load the kernel/ramdisk/dtb. This eliminates the need for a bootwrapper and produces a more realistic boot sequence with virtual models. Though the semihosting code is quite generic, support for armv7 in fastmodel is less useful due to the wide range of available silicon and the lack of a free armv7 fastmodel, so this change contains an untested armv7 placeholder for the service trap opcode. Please refer to doc/README.semihosting for a more detailed description of semihosting and how it is used with the armv8 virtual platforms. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Cc: trini@ti.com Cc: fenghua@phytium.com.cn Cc: bhupesh.sharma@freescale.com
* Merge remote-tracking branch 'u-boot-samsung/master'Albert ARIBAUD2014-07-01-193/+582
|\ | | | | | | | | | | | | | | Conflicts: boards.cfg Conflict was trivial between goni maintainer change and lager_nor removal.
| * Exynos5420: Introduce support for the Peach-Pit boardAkshay Saraswat2014-06-23-93/+281
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While the Exynos5420 chip is used in both Smdk5420 and in the Peach-Pit line of devices, there could be other boards using the same chip, so a common configuration file is being added (exynos5420.h) as well as two common device tree files (exynos54xx.dtsi & exynos5420.dtsi). The peach board as declared in boards.cfg is a copy of smdk5420 declaration. The configuration files are similar, but define different default device trees, console serial ports and prompts. The device tree files for smdk5420 and peach-pit inherit from the same common file. Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * Exynos5420: Let macros be used for exynos5420Akshay Saraswat2014-06-23-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | Macros defined in exynos5_setup.h specific to SMDK5420 are required for Peach-Pit too. Hence, replacing CONFIG_SMDK5420 with CONFIG_EXYNOS5420 to enable these macros for all the boards based on Exynos5420. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * Exynos5420: DMC: Add software read levelingAkshay Saraswat2014-06-13-7/+255
| | | | | | | | | | | | | | | | | | | | | | | | | | Sometimes Read DQ and DQS are not in phase. Since, this phase shift differs from board to board, we need to calibrate it at DRAM init phase, that's read DQ calibration. This patch adds SW Read DQ calibration routine to compensate this skew. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * DMC: exynos5420: Gate CLKM to when reading PHY_CON13Doug Anderson2014-06-13-5/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | when CLKM is running. If we stop CLKM when sampling it the glitches all go away, so we'll do that as per Samsung suggestion. We also check the "is it locked" bits of PHY_CON13 and loop until they show the the value sampled actually represents a locked value. It doesn't appear that the glitching and "is it locked" are related, but it seems wise to wait until the PHY tells us the value is good before we use it. In practice we will not loop more than a couple times (and usually won't loop at all). Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * Exynos5420: Remove code for enabling read levelingAkshay Saraswat2014-06-13-71/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch intends to remove all code which enables hardware read leveling. All characterization environments may not cope up with h/w read leveling enabled, so we must disable this. Also, disabling h/w read leveling improves the MIF LVcc value (LVcc value is the value at which DDR will fail to work properly). Improving LVcc means we have enough voltage margin for MIF. When h/w leveling is enabled, we have almost zero volatge margin. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * Exynos5: DMC: Modify the definition of ddr3_mem_ctrl_initAkshay Saraswat2014-06-13-13/+5
| | | | | | | | | | | | | | | | | | | | Passing fewer arguments is better and mem_iv_size is never used. Let's keep only one argument and make it cleaner. Signed-off-by: Hatim Ali <hatim.rv@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * Revert "exynos: Enable PSHOLD in SPL"Minkyu Kang2014-06-13-2/+0
| | | | | | | | This reverts commit eb0dd9986c3883820ff888c3738b013c0a7d918c.
* | Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'Albert ARIBAUD2014-07-01-1/+1
|\ \
| * | tegra20: display: fix checking of return valueJeroen Hofstee2014-06-19-1/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | The calling code seems a bit in doubt about the return value of fdtdec_lookup_phandle. Since it returns a negative value on error (and fdt_node_offset_by_phandle as well), check for that. cc: Wei Ni <wni@nvidia.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2014-07-01-283/+94
|\ \
| * | OMAP: disable gpmc timeout safely for reenablingStefano Babic2014-06-19-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | gpmc timeout is disabled and the reset counter is set to 0. However, if later a driver activates the timeout setting the reset to a valid value, the old reset value with zero is still valid for the first access. In fact, the timeout block loads the reset counter after a successful access. Found on a am335x board with a FPGA connected to the GPMC bus together with the NAND. When the FPGA driver in kernel activates the timeout, the system hangs at the first access by the NAND driver. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | omap3: board: trivial: add void for no argsJeroen Hofstee2014-06-19-2/+2
| | | | | | | | | | | | Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
| * | cpu: armv7: am33x: ddr: write emif ref_ctrl_shadow registerFelipe Balbi2014-06-19-0/+1
| | | | | | | | | | | | Signed-off-by: Felipe Balbi <balbi@ti.com>
| * | ARM: keystone: aemif: move aemif driver to drivers/memory/ti-aemif.cKhoronzhuk, Ivan2014-06-19-105/+43
| | | | | | | | | | | | | | | | | | | | | | | | Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * | mtd: nand: davinci: add header file for driver definitionsKhoronzhuk, Ivan2014-06-19-175/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The definitions inside emif_defs.h concern davinci nand driver and should be in it's header. So create header file for davinci nand driver and move definitions from emif_defs.h and nand_defs.h to it. Acked-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> [trini: Fixup more davinci breakage] Signed-off-by: Tom Rini <trini@ti.com>
| * | omap: Don't enable GPMC CS0 with nothing attachedAsh Charles2014-06-19-1/+2
| |/ | | | | | | | | | | | | | | | | | | | | If CONFIG_(NAND|NOR|ONENAND) is not defined, no configuration is set for GPMC on chip select #0---size is 0. In this case, the GPMC configuration should be reset but not enabled. Enabling causes the Gumstix DuoVero board to hang when entering Linux. Signed-off-by: Ash Charles <ashcharles@gmail.com> [trini: Switch to testing base as GPMC_SIZE_256M is 0x0] Signed-off-by: Tom Rini <trini@ti.com>
* | Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2014-06-30-162/+962
|\ \
| * | vf610: fix build due to missing sys_proto.hStefano Babic2014-06-25-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | commit 67a04ab3ab8522a3a34491853e46105317580df5 fix the build for MX25. The same error happens for VF610 SOC. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | imx: correct HAB status for new chip TOStefano Babic2014-06-17-14/+82
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to: http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/log/?h=imx_v2009.08_3.0.35_4.1.0 ENGR00287268 mx6: fix the secure boot issue on the new tapout chip commit 424cb1a79e9f5ae4ede9350dfb5e10dc9680e90b newer i.MX6 silicon revisions have an updated ROM and HAB API table. Please see also: i.MX Applications Processors Documentation Engineering Bulletins EB803, i.MX 6Dual/6Quad Applications Processor Silicon Revsion 1.2 to 1.3 Comparison With this change the secure boot status is correctly displayed Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | mx6: Fix definition of IOMUXC_GPR12_DEVICE_TYPE_RCFabio Estevam2014-06-17-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mx6 reference manual incorrectly states that the DEVICE_TYPE field of IOMUXC_GPR12 register should be configured as '0010' for setting the PCI controller in RC mode. The correct value should be '0100' instead. This also aligns with the same value used in the mx6 pci kernel driver. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
| * | MX25: fix build due to missing sys_proto.hStefano Babic2014-06-06-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | THe mx25 arch does not have a sys_proto.h file. Instead of creating a dummy file, the file is not included for this SOC. Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | imx: sata: return failure if not IMX6Q/IMX6DTim Harvey2014-06-06-1/+6
| | | | | | | | | | | | | | | | | | | | | The IMX6QUAD/DUAL have SATA, but the IMX6SOLO/DL do not. Return instead of configuring the SATA clock and GPR13 registers. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
| * | imx: iomux: add macros to setup iomux for multiple SoC typesTim Harvey2014-06-06-2/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allow imx_iomux_v3_setup_multiple_pads to take a multi-cpu pad_list and add macros for declaring the pad_list that take into account the SoC types supported using CONFIG_MX6QDL (supports both the MX6Q and MX6DL iomux). Cc: Stefan Roese <sr@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Andy Ng <andreas2025@gmail.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
| * | mx6: add mmdc configuration for MX6Q/MX6DLTim Harvey2014-06-06-0/+563
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - add function for configuring iomux based on board-specific regs - add function for configuring mmdc based on board-specific and chip-specific data Cc: Stefan Roese <sr@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Andy Ng <andreas2025@gmail.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
| * | mx6: add structs for mmdc and ddr iomux registersTim Harvey2014-06-06-0/+159
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add memory-mapped structures for MMDC iomux and configuration. Note that whi the MMDC configuration registers are common between the IMX6DQ (IMX6DUAL/IMX6QUAD) and IMX6SDL (IMX6SOLO/IMX6DUALLITE) types the iomux registers differ. This requires two sets of structures. Add structures to describe DDR3 device information, system information (memory layout, etc), and MMDC calibration registers that can be used to configure the MMDC dynamically. We define these structures for SPL builds instead of including mx6q-ddr.h an mx6dl-ddr.h which use the same namespace and are only useful for imximage cf files. Cc: Stefan Roese <sr@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Andy Ng <andreas2025@gmail.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
| * | imx: add comments and remove unused struct fieldsTim Harvey2014-06-06-9/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add comment block for the imx_ddr_size function and remove the extra unused fields from struct esd_mmdc_regs which are also not common between IMX53 and IMX6. Cc: Stefan Roese <sr@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Andy Ng <andreas2025@gmail.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
| * | mx6: add boot device support for SPLTim Harvey2014-06-06-0/+82
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a common spl.c file to support boot device functions needed for SPL such as detecting the boot device. Cc: Stefan Roese <sr@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Andy Ng <andreas2025@gmail.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
| * | spl: consolidate arch/arm/include/asm/arch-*/spl.hMasahiro Yamada2014-06-06-135/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | arch/arm/include/asm/spl.h requires all SoCs to have arch/arm/include/asm/arch-*/spl.h. But many of them just define BOOT_DEVICE_* macros. Those macros are used in the "switch (boot_device) { ... }" statement in common/spl/spl.c. So they should not be archtecture specific, but be described as a simpile enumeration. This commit merges most of arch/arm/include/asm/arch-*/spl.h into arch/arm/include/asm/spl.h. With a little more effort, arch-zynq/spl.h and arch-socfpga/spl.h will be merged, while I am not sure about OMAP and Exynos. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com> CC: Stefano Babic <sbabic@denx.de> CC: Minkyu Kang <mk7.kang@samsung.com> Cc: Dinh Nguyen <dinguyen@altera.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Michal Simek <monstr@monstr.eu> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tim Harvey <tharvey@gateworks.com> Tested-by: Bo Shen <voice.shen@atmel.com> [on sama5d3xek board for at91 part] Acked-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stefano Babic <sbabic@denx.de> [applying Tim's i.MX6 patches] Acked-by: Tom Rini <trini@ti.com>
* | | Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master'Albert ARIBAUD2014-06-25-0/+1
|\ \ \
| * | | arm: zynq: fix a bug in Zynq linker scriptMasahiro Yamada2014-06-17-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 41623c91 moved exception handlers to ".vectores" section but it missed to adjust Zynq linker script. Zynq boards hang up after relocation because "_start" symbol does not point to the correct address and gd->relocaddr gets insane. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Michal Simek <monstr@monstr.eu> Tested-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | | | Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2014-06-25-202/+1777
|\ \ \ \
| * | | | sandbox: change local_irq_save() to macroMasahiro Yamada2014-06-23-6/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | local_irq_save() should be a macro, not a function because local_irq_save() saves flag to the given argument. GCC is silent about this issue, but Clang warns: In file included from lib/asm-offsets.c:15: In file included from include/common.h:20: In file included from include/linux/bitops.h:110: arch/sandbox/include/asm/bitops.h:59:17: warning: variable 'flags' is uninitialized when used here [-Wuninitialized] local_irq_save(flags); ^~~~~ That change causes another warning: In file included from include/linux/bitops.h:110:0, from include/common.h:20, from lib/asm-offsets.c:15: arch/sandbox/include/asm/bitops.h: In function ‘test_and_set_bit’: arch/sandbox/include/asm/bitops.h:56:16: warning: unused variable ‘flags’ [-Wunused-variable] So, flags should be set to __always_unused. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
| * | | | sandbox: terminate os_dirent_ls() result listStephen Warren2014-06-23-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Each node in the linked-list that os_dirent_ls() returns has its next pointer set only when the next node is created. For the last node in the list, there is no next node, so this never happens, and the next pointer is never initialized. Explicitly initialize the next pointer so that it isn't dangling. Without this, "sb ls" might crash. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
| * | | | x86: Enable 32-bit build using x86_64 multilib toolchainVasili Galka2014-06-23-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Until now building the x86 arch boards required 32-bit toolchain. As many x86_64 toolchains come with 32-bit support (multilib) that's a good idea to enable build with such toolchains. The change required was to specify the usage of 32-bit explicitly to the compiler and the linker (-m32 and -m elf_i386 flags) and locate the right libgcc path. Signed-off-by: Vasili Galka <vvv444@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
| * | | | tegra: dts: Bring in GPIO bindings from linuxSimon Glass2014-06-20-28/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | These files are taken from Linux 3.14. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com>
| * | | | Makefile: Support include files for .dts filesSimon Glass2014-06-20-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Linux supports this, and if we are to have compatible device tree files, U-Boot should also. Avoid giving the device tree files access to U-Boot's include/ directory. Only include/dt-bindings is accessible. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | | | sandbox: Support iotrace featureSimon Glass2014-06-20-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Support the iotrace feature for sandbox, and enable it, using some dummy I/O access methods. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | | | arm: Support iotrace featureSimon Glass2014-06-20-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Support the iotrace feature for ARM, when enabled. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | | | m68k: Remove CONFIG_CMD_BEDBUG related codeVasili Galka2014-06-19-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This flag does not compile on m68k since 2003 (8bde7f7) when a required "cmd_bedbug.h" header was removed. Eleven years passed, lets clean up a little... Signed-off-by: Vasili Galka <vvv444@gmail.com>
| * | | | .gitignore: drop include/asm/proc from ignore patternMasahiro Yamada2014-06-19-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 7d89982b stopped creating symbolic link arch/${arch}/include/asm/proc. arch/.gitignore should be updated. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Vasili Galka <vvv444@gmail.com>
generated by cgit v1.1 at 2024-11-09 20:54:27 +0000