summaryrefslogtreecommitdiff
path: root/arch
Commit message (Collapse)AuthorAgeLines
* powerpc/mpc8xxx: Enable 3-way and 4-way DDR interleavingYork Sun2012-08-23-318/+455
| | | | | | | | Restructure DDR interleaving option to support 3 and 4 DDR controllers for 2-, 3- and 4-way interleaving. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Add support for cas latency 12 and aboveYork Sun2012-08-23-7/+21
| | | | | | | | Required by JEDEC 79-3E for high speed DDR3. Also change "CSn disabled" message to debug. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Add fine timing support for DDR3York Sun2012-08-23-12/+36
| | | | | | | | When the DDR3 speed goes higher, we need to utilize fine offset from SPD. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Skip zero values for DDR debug registersYork Sun2012-08-23-3/+11
| | | | | | | | | | | Some debug registers have non-zero default out of reset. If software is not setting debug registers, skip writing to them to avoid unnecessary overriding. Also add debug messages for workarounds and debug registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: fix core id for multicore bootingYork Sun2012-08-23-6/+53
| | | | | | | | | | For the cores with multiple threads, we need to figure out which physical core a thread belongs. To match the core ids, update PIR registers and spin tables. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Added new ext fields to IFCKumar Gala2012-08-23-6/+24
| | | | | | | | | | In case more than 32 bit address is used, the EXT bit should be set. Need to fix up address map for IFC #CS for 4, also need to move # of IFC banks into config_mpc85xx.h Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Add IFC offset for DPAA/Corenet platformsKumar Gala2012-08-23-0/+1
| | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Add e6500 processor detectionKumar Gala2012-08-23-0/+4
| | | | | Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: use topology registers to calculate number of coresYork Sun2012-08-23-9/+70
| | | | | | | | | We have actual topology infomation to find out exactly which core is present. Calculate the number of cores if not specified. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Add immap for topology and rcpm registersYork Sun2012-08-23-1/+87
| | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add IFC LAW target ID for FSL High-End SoCPrabhakar Kushwaha2012-08-23-0/+1
| | | | | | | | | | Freescale's High-End SoC are going to have Integrated Flash controller (IFC)'s support. So add IFC LAW target ID support for High-End SoC or corenet SoC. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx:Enable debugger support to missed e500v2 SoCPrabhakar Kushwaha2012-08-23-0/+4
| | | | | | | | | | | | | | | Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some restrictions on external debugging (JTAG). Need to define define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be used during boot to work around the limitations. Enable missed e500v2 SoC i.e. MPC8536, MPC8544, MPC8548 and MPC8572 for debug support. Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Cc: Tang Yuantian <Yuantian.Tang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/fsl-corenet: work around erratum A004510Scott Wood2012-08-23-0/+330
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Erratum A004510 says that under certain load conditions, modified cache lines can be discarded, causing data corruption. To work around this, several CCSR and DCSR register updates need to be made in a careful manner, so that there is no other transaction in corenet when the update is made. The update is made from a locked cacheline, with a delay before to flush any previous activity, and a delay after to flush the CCSR/DCSR update. We can't use a readback because that would be another corenet transaction, which is not allowed. We lock the subsequent cacheline to prevent it from being fetched while we're executing the previous cacheline. It is filled with nops so that a branch doesn't cause us to fetch another cacheline. Ordinarily we are running in a cache-inhibited mapping at this point, so we temporarily change that. We make it guarded so that we should never see a speculative load, and we never do an explicit load. Thus, only the I-cache should ever fill from this mapping, and we flush/unlock it afterward. Thus we should avoid problems from any potential cache aliasing between inhibited and non-inhibited mappings. NOTE that if PAMU is used with this patch, it will need to use a dedicated LAW as described in the erratum. This is the responsibility of the OS that sets up PAMU. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/fsl-corenet: remove dead variant symbolsScott Wood2012-08-23-69/+4
| | | | | | | | | | | These are not supported as individual build targets, but instead are supported by another target. The dead p4040 defines in particular had bitrotted significantly. Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: remove support for the Freescale P3060Timur Tabi2012-08-23-261/+2
| | | | | | | | The P3060 was cancelled before it went into production, so there's no point in supporting it. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: add support for FM2 DTSEC5Timur Tabi2012-08-23-0/+8
| | | | | | | | Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second Fman, so add the Fman and SerDes macros for that DTSEC. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* p1014rdb: set ddr bus width properly depending on SVRMatthew McClintock2012-08-23-0/+1
| | | | | | | | | | Currently, for NAND boot for the P1010/4RDB we hard code the DDR configuration. We can still dynamically set the DDR bus width in the nand spl so the P1010/4RDB boards can boot from the same u-boot image Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Remove P1015 and P1016 from CPU listYork Sun2012-08-23-39/+2
| | | | | | | | P1015 is the same as P1011 and P1016 is the same as P1012 from software point of view. They have different packages but share SVRs. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Master module for boot from PCIELiu Gang2012-08-23-22/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For the powerpc processors with PCIE interface, boot location can be configured from one PCIE interface by RCW. The processor booting from PCIE can do without flash for u-boot image. The image can be fetched from another processor's memory space by PCIE link connected between them. The processor booting from PCIE is slave, the processor booting from normal flash memory space is master, and it can help slave to boot from master's memory space. When boot from PCIE, slave's core should be in holdoff after powered on for some specific requirements. Master will release the slave's core at the right time by PCIE interface. Environment and requirement: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image is in master NOR flash. 3. Normally boot from local NOR flash. 4. Configure PCIE system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to one PCIE interface by RCW. 3. RCW should configure the SerDes, PCIE interfaces correctly. 4. Must set all the cores in holdoff by RCW. 5. Must be powered on before master's boot. For the master module, need to finish these processes: 1. Initialize the PCIE port and address space. 2. Set inbound PCIE windows covered slave's u-boot image stored in master's NOR flash. 3. Set outbound windows in order to configure slave's registers for the core's releasing. 4. Should set the environment variable "bootmaster" to "PCIE1", "PCIE2" or "PCIE3" using the following command: setenv bootmaster PCIE1 saveenv Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Get rid of the CONFIG_SRIOBOOT_SLAVE_PORTx macroLiu Gang2012-08-23-0/+1
| | | | | | | | | | | | | | | | When compile the slave image for boot from SRIO, no longer need to specify which SRIO port it will boot from. The code will get this information from RCW and then finishes corresponding configurations. This has the following advantages: 1. No longer need to rebuild an image when change the SRIO port for boot from SRIO, just rewrite the new RCW with selected port, then the code will get the port information by reading new RCW. 2. It will be easier to support other boot location options, for example, boot from PCIE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Get rid of the SRIOBOOT_MASTER build targetLiu Gang2012-08-23-99/+63
| | | | | | | | | | | | | | | | | | | | | | Get rid of the SRIOBOOT_MASTER build target, and to support for serving as a SRIO boot master via environment variable. Set the environment variable "bootmaster" to "SRIO1" or "SRIO2" using the following command: setenv bootmaster SRIO1 saveenv The "bootmaster" will enable the function of the SRIO boot master, and this has the following advantages compared with SRIOBOOT_MASTER build configuration: 1. Reduce a build configuration item in boards.cfg file. No longer need to build a special image for master, just use a normal target image and set the "bootmaster" variable. 2. No longer need to rebuild an image when change the SRIO port for boot from SRIO, just set the corresponding value to "bootmaster" based on the using SRIO port. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Make NMG_CPU_A011 workaround conditionalYork Sun2012-08-23-3/+56
| | | | | | | | | | | | | | | | | This erratum applies to the following SoCs: P4080 rev 1.0, 2.0, fixed in rev 3.0 P2041 rev 1.0, 1.1, fixed in rev 2.0 P3041 rev 1.0, 1.1, fixed in rev 2.0. Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround may degrade performance. P4080 erratum CPU22 shares the same workaround. So it is always enabled for P4080. For other SoCs, it can be disabled by hwconfig with syntax: fsl_cpu_a011:disable Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc: Stack Pointer not properly alignedJoakim Tjernlund2012-08-22-3/+2
| | | | | | | | | The code first aligns the SP to 16 then subtract 8, making it 8 bytes aligned. Furthermore the initial stack frame not quite correct either. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mpc85xx: Initial SP alignment is wrong.Joakim Tjernlund2012-08-22-11/+5
| | | | | | | | | | | | PowerPC mandates SP to be 16 bytes aligned. Furthermore, a stack frame is added, pointing to the reset vector which may in the way when gdb is walking the stack because the reset vector may not accessible depending on emulator settings. Also use a temp register so gdb doesn't pick up intermediate values. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* nds32: fix unused pmu_init warningMike Frysinger2012-08-11-0/+2
| | | | | | | | | | | Fixes the build-time warning: board.c: At top level: board.c:106: warning: 'pmu_init' defined but not used This makes the ifdef logic at the call site match the logic at the function definition. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* nds32: delete unused local variableMike Frysinger2012-08-11-1/+0
| | | | | | | | Fixes the build-time warning: board.c: In function 'board_init_r': board.c:304: warning: unused variable 's' Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* nds32: drop bi_enetaddr from global dataMike Frysinger2012-08-11-1/+0
| | | | | | | Nothing is using this, so punt it from the gd. Seems to just be a copy & paste wart from the initial port. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* openrisc: Work around potential relocation issuesJulius Baxter2012-08-09-6/+13
| | | | | | | | | | When reset code is in flash, the jump instructions emitted by the compiler are relative instead of absolute jumps. A fix to the reset code to make correct jumps to the beginning of code relocated to RAM have also been added. Signed-off-by: Julius Baxter <juliusbaxter@gmail.com>
* powerpc: Fix declaration type for I/O functionsPrabhakar Kushwaha2012-08-09-10/+10
| | | | | | | | | Prototype declaration of I/O operation functions are not correct. as both 'extern' and function definition are at same place. Chage protoype declaration as static. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
* powerpc:Fix return type & parameter passed for I/O functionsPrabhakar Kushwaha2012-08-09-15/+15
| | | | | | | | | | | | Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type u8/u16/u32. Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type uniform across the file changed to u32 Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32 should not be 'int'.Change it to type u8/u16/u32. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
* global_data: unify global flag definesMike Frysinger2012-08-09-181/+14
| | | | | | | All the global flag defines are the same across all arches. So unify them in one place, and add a simple way for arches to extend for their needs. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2012-08-09-22/+29
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-mpc85xx: powerpc/85xx: use CONFIG_SYS_FSL_PCIE_COMPAT macro when setting the PCI LIODNs powerpc/mpc85xx: Ignore E bit for BSC9130/1 powerpc/sgmii: To support PHY link state auto detect in SGMII mode powerpc/85xx: improve definition of BR_PHYS_ADDR macro powerpc/p2041: configure the CPLD lane_mux according to RCW powerpc/ddr: fix fsl_ddr_get_dimm_params compile error powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is defined powerpc/mpc8xxx: fix workaround for errata DDR111 and DDR134 for DDR over 4GB powerpc/p1022ds: fix DIU/LBC switching with NAND enabled powerpc/p1022ds: add support for SPI and SD boot Signed-off-by: Wolfgang Denk <wd@denx.de>
| * powerpc/85xx: use CONFIG_SYS_FSL_PCIE_COMPAT macro when setting the PCI LIODNsTimur Tabi2012-08-08-14/+14
| | | | | | | | | | | | | | | | | | | | The SET_PCI_LIODN() macro takes a compatible property string as a parameter, so that it knows which PCI device tree node to look for. The calls to these macros are using a hard-coded string, but we already have the CONFIG_SYS_FSL_PCIE_COMPAT macro which contains the same string, so we should use that. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc85xx: Ignore E bit for BSC9130/1York Sun2012-08-08-2/+0
| | | | | | | | | | | | | | | | Commit 48f6a5c34 removed E bit. BSC9130/1 were left out due to patch apply timing. Remove them now. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/85xx: improve definition of BR_PHYS_ADDR macroTimur Tabi2012-08-08-3/+3
| | | | | | | | | | | | | | | | The BR_PHYS_ADDR(x) macro was missing parentheses around "x" in the macro definition, so callers had to supply their own parenthesis. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/ddr: fix fsl_ddr_get_dimm_params compile errorShaohui Xie2012-08-08-1/+1
| | | | | | | | | | | | | | | | | | | | fsl_ddr_get_dimm_params() should be wrapped by CONFIG_SYS_DDR_RAW_TIMING, otherwise, when using fixed_sdram() instead of using SPD, it will cause compile error. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: fix workaround for errata DDR111 and DDR134 for DDR over 4GBYork Sun2012-08-08-2/+11
| | | | | | | | | | | | | | | | | | The fix for errata workaround is to avoid covering physical address 0xff000000 to 0xffffffff during the implementation. Early commit eb672e92 works until DDR size exceeds 4GB. This fix works for DDR size up to 64GB. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | sh: modify checkcpu() for SH-4AYoshihiro Shimoda2012-08-08-0/+4
|/ | | | | | | | Even if using CPU is SH-4A, the previous code always put "SH4". This patch fixes it. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk2012-07-31-15/+289
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-i2c: km/common: remove printfs for i2c deblocking code CONFIG: SMDK5250: I2C: Enable I2C I2C: Add support for Multi channel I2C: Modify the I2C driver for EXYNOS5 I2C: Move struct s3c24x0_i2c to a common place. EXYNOS: PINMUX: Add pinmux support for I2C EXYNOS5: define EXYNOS5_I2C_SPACING EXYNOS: Add I2C base address. EXYNOS: CLK: Add i2c clock mx6qsabrelite: add i2c multi-bus support imx-common: add i2c.c for bus recovery support i.mx53: add definition for I2C3_BASE_ADDR i.mx: iomux-v3.c: move to imx-common directory i.mx: iomux-v3.h: move to imx-common include directory iomux-v3: remove include of mx6x_pins.h mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support mxc_i2c: add bus recovery support mxc_i2c: prep work for multiple busses support mxc_i2c: add i2c_regs argument to i2c_imx_stop mxc_i2c: add retries mxc_i2c: check for arbitration lost mxc_i2c: change slave addr if conflicts with destination. mxc_i2c: don't disable controller after every transaction mxc_i2c: place i2c_reset code inline mxc_i2c: place imx_start code inline mxc_i2c: remove redundant read mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into wait_for_sr_state mxc_i2c.c: code i2c_probe as a 0 length i2c_write mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_write mxc_i2c: create i2c_init_transfer mxc_i2c: clear i2sr before waiting for bit mxc_i2c: create tx_byte function mxc_i2c: remove ifdef of CONFIG_HARD_I2C mxc_i2c: fix i2c_imx_stop i2c: deblock i2c bus also if accessed before realocation Signed-off-by: Wolfgang Denk <wd@denx.de>
| * I2C: Move struct s3c24x0_i2c to a common place.Rajeshwari Shinde2012-07-31-10/+0
| | | | | | | | | | | | | | | | | | | | struct s3c24x0_i2c is being moved to common local header file so that the same can be used by s3c series and exynos series SoCs. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
| * EXYNOS: PINMUX: Add pinmux support for I2CRajeshwari Shinde2012-07-31-0/+60
| | | | | | | | | | | | | | This patch adds pinmux code for I2C. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
| * EXYNOS5: define EXYNOS5_I2C_SPACINGRajeshwari Shinde2012-07-31-0/+2
| | | | | | | | | | | | | | | | This patch defined EXYNOS5_I2C_SPACING used to calculate I2C channel base address. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
| * EXYNOS: Add I2C base address.Rajeshwari Shinde2012-07-31-0/+3
| | | | | | | | | | | | | | | | This patch adds the base address for I2C. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
| * EXYNOS: CLK: Add i2c clockRajeshwari Shinde2012-07-31-0/+34
| | | | | | | | | | | | | | | | | | This adds i2c clock information for EXYNOS5. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
| * imx-common: add i2c.c for bus recovery supportTroy Kisky2012-07-31-1/+186
| | | | | | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
| * i.mx53: add definition for I2C3_BASE_ADDRTroy Kisky2012-07-31-0/+1
| | | | | | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
| * i.mx: iomux-v3.c: move to imx-common directoryTroy Kisky2012-07-31-2/+2
| | | | | | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
| * i.mx: iomux-v3.h: move to imx-common include directoryTroy Kisky2012-07-31-2/+2
| | | | | | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
| * iomux-v3: remove include of mx6x_pins.hTroy Kisky2012-07-31-1/+0
| | | | | | | | | | | | | | This include is not needed. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Jason Liu <r64343@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-microblazeWolfgang Denk2012-07-31-94/+192
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-microblaze: microblaze: Wire up SPI driver spi: microblaze: Adds driver for Xilinx SPI controller microblaze: intc: Clear interrupt code microblaze: Call serial multi initialization microblaze: Move __udelay implementation microblaze: Remove extern from board.c microblaze: Wire up dts configuration fdt: Add board specific dts inclusion microblaze: Move individual board linker scripts to common script in cpu tree. microblaze: Add gpio.h microblaze: Add missing undefs for UBI and UBIFS microblaze: Expand and correct configuration comments microblaze: Enable ubi support microblaze: Avoid compile error on systems without cfi flash microblaze: Remove wrong define CONFIG_SYS_FLASH_PROTECTION Conflicts: drivers/spi/Makefile Signed-off-by: Wolfgang Denk <wd@denx.de>
generated by cgit v1.1 at 2024-09-14 00:43:47 +0000