summaryrefslogtreecommitdiff
path: root/arch/powerpc
Commit message (Collapse)AuthorAgeLines
* powerpc/85xx: Add P5040 processor supportTimur Tabi2012-10-22-0/+372
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the Freescale P5040 SOC, which is similar to the P5020. Features of the P5040 are: Four P5040 single-threaded e5500 cores built Up to 2.4 GHz with 64-bit ISA support Three levels of instruction: user, supervisor, hypervisor CoreNet platform cache (CPC) 2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving support Up to 1600MT/s Memory pre-fetch engine DPAA incorporating acceleration for the following functions Packet parsing, classification, and distribution (FMAN) Queue management for scheduling, packet sequencing and congestion management (QMAN) Hardware buffer management for buffer allocation and de-allocation (BMAN) Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes 20 lanes at up to 5 Gbps Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces Two 10 Gbps Ethernet MACs Ten 1 Gbps Ethernet MACs High-speed peripheral interfaces Two PCI Express 2.0/3.0 controllers Additional peripheral interfaces Two serial ATA (SATA 2.0) controllers Two high-speed USB 2.0 controllers with integrated PHY Enhanced secure digital host controller (SD/MMC/eMMC) Enhanced serial peripheral interface (eSPI) Two I2C controllers Four UARTs Integrated flash controller supporting NAND and NOR flash DMA Dual four channel Support for hardware virtualization and partitioning enforcement Extra privileged level for hypervisor support QorIQ Trust Architecture 1.1 Secure boot, secure debug, tamper detection, volatile key storage Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/p5040ds: add per pci endpoint liodn offset listLaurentiu Tudor2012-10-22-0/+52
| | | | | | | | | | | | | | | | | | | | Add a new device tree property named "fsl,liodn-offset-list" holding a list of per pci endpoint permitted liodn offsets. This property is useful in virtualization scenarios that implement per pci endpoint partitioning. The final liodn of a partitioned pci endpoint is calculated by the hardware, by adding these offsets to pci controller's base liodn, stored in the "fsl,liodn" property of its node. The liodn offsets are interleaved to get better cache utilization. As an example, given 3 pci controllers, the following liodns are generated for the pci endpoints: pci0: 193 256 259 262 265 268 271 274 277 pci1: 194 257 260 263 266 269 272 275 278 pci2: 195 258 261 264 267 270 273 276 279 Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: define SRIO LIODN functions only if SRIO is definedTimur Tabi2012-10-22-1/+11
| | | | | | | | The P5040 does not have SRIO support, so there are no SRIO LIODNs. Therefore, the functions that set the SRIO LIODNs should not be compiled. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: introduce SET_PCI_LIODN_BASE, for setting PCI LIODNsLaurentiu Tudor2012-10-22-1/+8
| | | | | | | | | | | | The liodn for the new PCIE controller included in P5040DS is no longer set through a register in the guts register block but with one in the PCIE register block itself. Update the PCIE CCSR structure to add the new liodn register and add a new dedicated SET_PCI_LIODN_BASE macro that puts the liodn in the correct register. Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: fix Unicode characters in release.STimur Tabi2012-10-22-12/+12
| | | | | | | | Commit 709389b6 unintentionally used the Unicode version of the apostrophy. Replace it with the normal ASCII version. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/srio: Workaround for srio erratrm a004034Liu Gang2012-10-22-0/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Erratum: A-004034 Affects: SRIO Description: During port initialization, the SRIO port performs lane synchronization (detecting valid symbols on a lane) and lane alignment (coordinating multiple lanes to receive valid data across lanes). Internal errors in lane synchronization and lane alignment may cause failure to achieve link initialization at the configured port width. An SRIO port configured as a 4x port may see one of these scenarios: 1. One or more lanes fails to achieve lane synchronization. Depending on which lanes fail, this may result in downtraining from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane). 2. The link may fail to achieve lane alignment as a 4x, even though all 4 lanes achieve lane synchronization, and downtrain to a 1x. An SRIO port configured as a 1x port may fail to complete port initialization (PnESCSR[PU] never deasserts) because of scenario 1. Impact: SRIO port may downtrain to 1x, or may fail to complete link initialization. Once a port completes link initialization successfully, it will operate normally. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Fix USB device-tree fixupramneek mehresh2012-10-22-16/+34
| | | | | | | | | | | | | Fix usb device-tree fixup: - wrong modification of dr_mode and phy_type when "usb1" is not mentioned inside hwconfig string; now allows hwconfig strings like: "usb2:dr_mode=host,phy_type=ulpi" - add warning message for using usb_dr_mode and usb_phy_type env variables (if either is used) Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* P4080/esdhc: make the P4080 ESDHC13 errata workaround conditionalZang Roy-R619112012-10-22-7/+10
| | | | | | | | | | P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the workaround conditional. In formal release document, the errata number should be ESDHC13 instead of ESDHC136. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc mpc85xx: Only clear TSR:WIS in watchdog_reset.Mark Marshall2012-10-22-4/+1
| | | | | | | | | | | | We should only write TSR_WIS to the SPRN_TSR register in reset_85xx_watchdog. The old code would cause the timer interrupt to be acknowledged when the watchdog was reset, and we would then get no more timer interrupts. This bug would affect all mpc85xx boards that have the watchdog enabled. Signed-off-by: Mark Marshall <Mark.Marshall@omicron.at> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mpc85xx: make gpio_direction_output respect valueChris Packham2012-10-22-1/+4
| | | | | | | | | | | | | | Users of familiar with the Linux gpiolib API expect that value parameter to gpio_direction_output reflects the initial state of the output pin. gpio_direction_output was always driving the output low, now it drives it high or low according to the value provided. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc: Change bi_baudrate and global data baudrate to intSimon Glass2012-10-19-2/+2
| | | | | | | These don't need to be longs, so change them. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@ti.com>
* split mpc8xx hooks from cmd_ide.cPavel Herrmann2012-10-17-0/+233
| | | | | | | | | | | | | move most of mpc8xx hooks from cmd_ide.c into ide_preinit() and newly created ide_init_postreset() (invoked after calling ide_reset after ide_preinit), some cleanup to make checkpatch happy, enable IDE init hooks in configs of affected boards. confusingly, these hooks are used by more than just mpc8xx-based boards, and therefore are placed in arch/ppc/lib/ note: checkpatch still emits warnings about using volatile Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
* serial: Use default_serial_puts() in driversMarek Vasut2012-10-17-41/+5
| | | | | | | | | | Replace the in-place ad-hoc implementation of serial_puts() within the drivers with default_serial_puts() call. This cuts down on the code duplication quite a bit. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
* mpc82xx: Remove BMW board portStefan Roese2012-10-17-9/+4
| | | | | | | | | | | As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: James F. Dougherty <jfd@broadcom.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Marek Vasut <marex@denx.de>
* usb: lowlevel interface change to support multiple controllersLucas Stach2012-10-15-4/+4
| | | | | | | | | | | Carry an index in the lowlevel usb functions to make specify the respective usb controller. Also pass through an controller struct from lowlevel_init to the creation of the root usb device of this controller. Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Marek Vasut <marex@denx.de>
* ppc4xx: Remove AP1000 board supportStefan Roese2012-10-15-15/+0
| | | | | | | | | As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: James MacAulay <james.macaulay@amirix.com> Acked-by: Marek Vasut <marex@denx.de>
* ppc4xx: Remove ML2 board supportStefan Roese2012-10-15-1/+1
| | | | | | | | | As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Peter De Schrijver <p2@mind.be> Acked-by: Marek Vasut <marex@denx.de>
* ppc4xx: Remove IOP480 supportStefan Roese2012-10-15-400/+2
| | | | | | | | | | Since the IOP480 (PPC401/3 variant from PLX) is only used on 2 boards that are not actively maintained, lets remove support for it completely. This way the ppc4xx code will get a bit cleaner. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu> Acked-by: Marek Vasut <marex@denx.de>
* serial: Remove CONFIG_SERIAL_MULTI from remaining sourcesMarek Vasut2012-10-15-2/+0
| | | | | | | | | | | | Remove the parts depending either on disabled CONFIG_SERIAL_MULTI or ifdefs around CONFIG_SERIAL_MULTI parts since CONFIG_SERIAL_MULTI is now enabled by default. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: Remove CONFIG_SERIAL_MULTI from serial driversMarek Vasut2012-10-15-369/+39
| | | | | | | | | | | | Remove the support for not-CONFIG_SERIAL_MULTI part from serial port drivers and some board files. Since CONFIG_SERIAL_MULTI is now enabled by default, that part is a dead code. Remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into iop480 serial driverMarek Vasut2012-10-15-6/+59
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into iop480 serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the iop480 driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into mpc85xx serial driverMarek Vasut2012-10-15-11/+60
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into mpc85xx serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the mpc85xx driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into mpc8260 serial driversMarek Vasut2012-10-15-22/+120
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into both SCC and SMC mpc8260 serial drivers. These drivers were so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the mpc8260 drivers. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into mpc8220 serial driverMarek Vasut2012-10-15-6/+61
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into mpc8220 serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the mpc8220 driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into mpc5xx serial driverMarek Vasut2012-10-15-21/+74
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into mpc5xx serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the mpc5xx driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: mpc512x: Move serial registration from serial_initialize()Marek Vasut2012-10-15-0/+16
| | | | | | | | | | | | | | | | | | | | | | | Move the registration of serialN_device ports from default serial_initialize() into driver specific function called from serial_initialize(). This slims down the serial_initialize() call to a bare tracker of all possible serial port registration routines in U-Boot. The newly implemented mpc512x_serial_initialize() function, which is implemented inside of the mpc512x serial driver allows encapsulation of serialN_device within the mpc512x serial driver itself. Also, remove the exports of serialN_device from include/serial.h as they are no longer needed. This is simply because the implementation of default_serial_console() is wrapped into the mpx512x serial driver and the default console is picked by CONFIG_SERIAL<N> macro in config file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: mpc8xx: Move serial registration from serial_initialize()Marek Vasut2012-10-15-0/+11
| | | | | | | | | | | | | | | | | | | Move the registration of serial_smc and serial_scc ports from default serial_initialize() into CPU specific function called from serial_initialize(). This slims down the serial_initialize() call to a bare tracker of all possible serial port registration routines in U-Boot. The exports of both serial_scc_device and serial_smc_device can not yet be removed as they are still used in default_serial_console() calls. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Mike Frysinger <vapier@gentoo.org>
* serial: Properly spell out the structure member names of serial_driverMarek Vasut2012-10-15-41/+41
| | | | | | | | | | | | | | | | | Properly spell out the whole structure member names when an initialized varible is instantiated from the struct serial_driver. In case the structure definition for struct serial_driver undergoes reordering, there will be no impact on variables defined based on this structure. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: C Nauman <cnauman@diagraph.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Michal Simek <monstr@monstr.eu>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2012-09-25-926/+1359
|\
| * Revert "powerpc: Fix declaration type for I/O functions"Andy Fleming2012-08-23-10/+10
| | | | | | | | This reverts commit 20959471b5d07fdeb8603b918d80385aa2954711.
| * powerpc/85xx: clear out TLB on bootScott Wood2012-08-23-33/+48
| | | | | | | | | | | | | | | | Instead of just shooting down the entry that covers CCSR, clear out every TLB entry that isn't the one that we're executing out of. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Move HWCONFIG_BUFFER_SIZE into config.hYork Sun2012-08-23-5/+4
| | | | | | | | | | | | | | | | | | | | Before proper environment is setup, we extract hwconfig and put it into a buffer with size HWCONFIG_BUFFER_SIZE. We need to enlarge the buffer to accommodate longer string. Since this macro is used in multiple files, we move it into arch/powerpc/include/asm/config.h. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx DDR: Fix interactive DDR debuggingYork Sun2012-08-23-2/+2
| | | | | | | | | | | | | | | | Add one more argument to call function readline_into_buffer(). Fix print SPD format for negative values. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx DDR: Fall back to raw timing for first controller onlyYork Sun2012-08-23-1/+1
| | | | | | | | | | | | | | | | Only the first DIMM of first controller should fall back to raw timing parameters if SPD is missing or corrupted. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx DDR: Fix CAS latency calculationYork Sun2012-08-23-2/+4
| | | | | | | | | | | | | | Empty slot should be skipped when calculating CAS latency. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Fix bug for extended DDR timingYork Sun2012-08-23-20/+43
| | | | | | | | | | | | | | | | Faster DDR3 timing requires parameters exceeding previously defined range. Extended parameters are fixed. Added some debug messages. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Enable 3-way and 4-way DDR interleavingYork Sun2012-08-23-318/+455
| | | | | | | | | | | | | | | | Restructure DDR interleaving option to support 3 and 4 DDR controllers for 2-, 3- and 4-way interleaving. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Add support for cas latency 12 and aboveYork Sun2012-08-23-7/+21
| | | | | | | | | | | | | | | | Required by JEDEC 79-3E for high speed DDR3. Also change "CSn disabled" message to debug. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Add fine timing support for DDR3York Sun2012-08-23-12/+36
| | | | | | | | | | | | | | | | When the DDR3 speed goes higher, we need to utilize fine offset from SPD. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc85xx: Skip zero values for DDR debug registersYork Sun2012-08-23-3/+11
| | | | | | | | | | | | | | | | | | | | | | Some debug registers have non-zero default out of reset. If software is not setting debug registers, skip writing to them to avoid unnecessary overriding. Also add debug messages for workarounds and debug registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: fix core id for multicore bootingYork Sun2012-08-23-6/+53
| | | | | | | | | | | | | | | | | | | | For the cores with multiple threads, we need to figure out which physical core a thread belongs. To match the core ids, update PIR registers and spin tables. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * Added new ext fields to IFCKumar Gala2012-08-23-6/+24
| | | | | | | | | | | | | | | | | | | | In case more than 32 bit address is used, the EXT bit should be set. Need to fix up address map for IFC #CS for 4, also need to move # of IFC banks into config_mpc85xx.h Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * Add IFC offset for DPAA/Corenet platformsKumar Gala2012-08-23-0/+1
| | | | | | | | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * Add e6500 processor detectionKumar Gala2012-08-23-0/+4
| | | | | | | | | | Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: use topology registers to calculate number of coresYork Sun2012-08-23-9/+70
| | | | | | | | | | | | | | | | | | We have actual topology infomation to find out exactly which core is present. Calculate the number of cores if not specified. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Add immap for topology and rcpm registersYork Sun2012-08-23-1/+87
| | | | | | | | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc85xx: Add IFC LAW target ID for FSL High-End SoCPrabhakar Kushwaha2012-08-23-0/+1
| | | | | | | | | | | | | | | | | | | | Freescale's High-End SoC are going to have Integrated Flash controller (IFC)'s support. So add IFC LAW target ID support for High-End SoC or corenet SoC. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc85xx:Enable debugger support to missed e500v2 SoCPrabhakar Kushwaha2012-08-23-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some restrictions on external debugging (JTAG). Need to define define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be used during boot to work around the limitations. Enable missed e500v2 SoC i.e. MPC8536, MPC8544, MPC8548 and MPC8572 for debug support. Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Cc: Tang Yuantian <Yuantian.Tang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/fsl-corenet: work around erratum A004510Scott Wood2012-08-23-0/+330
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Erratum A004510 says that under certain load conditions, modified cache lines can be discarded, causing data corruption. To work around this, several CCSR and DCSR register updates need to be made in a careful manner, so that there is no other transaction in corenet when the update is made. The update is made from a locked cacheline, with a delay before to flush any previous activity, and a delay after to flush the CCSR/DCSR update. We can't use a readback because that would be another corenet transaction, which is not allowed. We lock the subsequent cacheline to prevent it from being fetched while we're executing the previous cacheline. It is filled with nops so that a branch doesn't cause us to fetch another cacheline. Ordinarily we are running in a cache-inhibited mapping at this point, so we temporarily change that. We make it guarded so that we should never see a speculative load, and we never do an explicit load. Thus, only the I-cache should ever fill from this mapping, and we flush/unlock it afterward. Thus we should avoid problems from any potential cache aliasing between inhibited and non-inhibited mappings. NOTE that if PAMU is used with this patch, it will need to use a dedicated LAW as described in the erratum. This is the responsibility of the OS that sets up PAMU. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/fsl-corenet: remove dead variant symbolsScott Wood2012-08-23-69/+4
| | | | | | | | | | | | | | | | | | | | | | These are not supported as individual build targets, but instead are supported by another target. The dead p4040 defines in particular had bitrotted significantly. Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit v1.1 at 2024-12-19 02:31:02 +0000