summaryrefslogtreecommitdiff
path: root/arch/powerpc
Commit message (Collapse)AuthorAgeLines
* powerpc/mpc8xxx: Update DDR registersYork Sun2012-10-22-3/+68
| | | | | | | | | | | | | | | | | | | | | | | | | | | | DDRC ver 4.7 adds DDR_SLOW bit in sdram_cfg_2 register. This bit needs to be set for speed lower than 1250MT/s. CDR1 and CDR2 are control driver registers. ODT termination valueis for IOs are defined. Starting from DDRC 4.7, the decoding of ODT for IOs is 000 -> Termsel off 001 -> 120 Ohm 010 -> 180 Ohm 011 -> 75 Ohm 100 -> 110 Ohm 101 -> 60 Ohm 110 -> 70 Ohm 111 -> 47 Ohm Add two write leveling registers. Each QDS now has its own write leveling start value. In case of zero value, the value of QDS0 will be used. These values are board-specific and are set in board files. Extend DDR register timing_cfg_1 to have 4 bits for each field. DDR control driver registers and write leveling registers are added to interactive debugging for easy access. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* fm/mEMAC: add mEMAC frame workRoy Zang2012-10-22-0/+290
| | | | | | | | | | | The multirate ethernet media access controller (mEMAC) interfaces to 10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface. Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add B4860 and variant SoCsYork Sun2012-10-22-0/+353
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Freescale B4860 and variant SoCs. Features of B4860 are (incomplete list): Six fully-programmable StarCore SC3900 FVP subsystems, divided into three clusters-each core runs up to 1.2 GHz, with an architecture highly optimized for wireless base station applications Four dual-thread e6500 Power Architecture processors organized in one cluster-each core runs up to 1.8 GHz Two DDR3/3L controllers for high-speed, industry-standard memory interface each runs at up to 1866.67 MHz MAPLE-B3 hardware acceleration-for forward error correction schemes including Turbo or Viterbi decoding, Turbo encoding and rate matching, MIMO MMSE equalization scheme, matrix operations, CRC insertion and check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration, and UMTS chip rate acceleration CoreNet fabric that fully supports coherency using MESI protocol between the e6500 cores, SC3900 FVP cores, memories and external interfaces. CoreNet fabric interconnect runs at 667 MHz and supports coherent and non-coherent out of order transactions with prioritization and bandwidth allocation amongst CoreNet endpoints. Data Path Acceleration Architecture, which includes the following: Frame Manager (FMan), which supports in-line packet parsing and general classification to enable policing and QoS-based packet distribution Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading of queue management, task management, load distribution, flow ordering, buffer management, and allocation tasks from the cores Security engine (SEC 5.3)-crypto-acceleration for protocols such as IPsec, SSL, and 802.16 RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and outbound). Supports types 5, 6 (outbound only) Large internal cache memory with snooping and stashing capabilities for bandwidth saving and high utilization of processor elements. The 9856-Kbyte internal memory space includes the following: 32 Kbyte L1 ICache per e6500/SC3900 core 32 Kbyte L1 DCache per e6500/SC3900 core 2048 Kbyte unified L2 cache for each SC3900 FVP cluster 2048 Kbyte unified L2 cache for the e6500 cluster Two 512 Kbyte shared L3 CoreNet platform caches (CPC) Sixteen 10-GHz SerDes lanes serving: Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total of up to 8 lanes Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue- less antenna connection Two 10-Gbit Ethernet controllers (10GEC) Six 1G/2.5-Gbit Ethernet controllers for network communications PCI Express controller Debug (Aurora) Two OCeaN DMAs Various system peripherals 182 32-bit timers Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add T4240 SoCYork Sun2012-10-22-7/+576
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Freescale T4240 SoC. Feature of T4240 are (incomplete list): 12 dual-threaded e6500 cores built on Power Architecture® technology Arranged as clusters of four cores sharing a 2 MB L2 cache. Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture v2.06-compliant) Three levels of instruction: user, supervisor, and hypervisor 1.5 MB CoreNet Platform Cache (CPC) Hierarchical interconnect fabric CoreNet fabric supporting coherent and non-coherent transactions with prioritization and bandwidth allocation amongst CoreNet end-points 1.6 Tbps coherent read bandwidth Queue Manager (QMan) fabric supporting packet-level queue management and quality of service scheduling Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving support Memory prefetch engine (PMan) Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: Packet parsing, classification, and distribution (Frame Manager 1.1) Queue management for scheduling, packet sequencing, and congestion management (Queue Manager 1.1) Hardware buffer management for buffer allocation and de-allocation (BMan 1.1) Cryptography acceleration (SEC 5.0) at up to 40 Gbps RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0) 32 SerDes lanes at up to 10.3125 GHz Ethernet interfaces Up to four 10 Gbps Ethernet MACs Up to sixteen 1 Gbps Ethernet MACs Maximum configuration of 4 x 10 GE + 8 x 1 GE High-speed peripheral interfaces Four PCI Express 2.0/3.0 controllers Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with Type 11 messaging and Type 9 data streaming support Interlaken look-aside interface for serial TCAM connection Additional peripheral interfaces Two serial ATA (SATA 2.0) controllers Two high-speed USB 2.0 controllers with integrated PHY Enhanced secure digital host controller (SD/MMC/eMMC) Enhanced serial peripheral interface (eSPI) Four I2C controllers Four 2-pin or two 4-pin UARTs Integrated Flash controller supporting NAND and NOR flash Two eight-channel DMA engines Support for hardware virtualization and partitioning enforcement QorIQ Platform's Trust Architecture 1.1 Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add T4 device definitionsAndy Fleming2012-10-22-2/+48
| | | | | | | | | | | | | | | | | | | | The T4 has added devices to previous corenet implementations: * SEC has 3 more DECO units * New PMAN device * New DCE device This doesn't add full support for the new devices. Just some preliminary support. Move PMAN LIODN to upper half of register Despite having only one LIODN, the PMAN LIODN is stored in the upper half of the register. Re-use the 2-LIODN code and just set the LIODN as if the second one is 0. This results in the actual LIODN being written to the upper half of the register. Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet2: fix mismatch DDR sync bit from RCWYork Sun2012-10-22-2/+8
| | | | | | | | Corenet 2nd generation Chassis doesn't have ddr_sync bit in RCW. Only async mode is supported. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet2: Add SerDes for corenet2York Sun2012-10-22-9/+281
| | | | | | | | | | | | | | | | | | | | | Create new files to handle 2nd generation Chassis as the registers are organized differently. - Add SerDes protocol parsing and detection - Add support of 4 SerDes - Add CPRI protocol in fsl_serdes.h The Common Public Radio Interface (CPRI) is publicly available specification that standardizes the protocol interface between the radio equipment control (REC) and the radio equipment (RE) in wireless basestations. This allows interoperability of equipment from different vendors,and preserves the software investment made by wireless service providers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add RCW bits and registers for SerDes for corenet2York Sun2012-10-22-5/+93
| | | | | | | | Corenet 2nd generation Chassis has different RCW and registers for SerDes. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/e6500: Move QCSP registers for QMan v3York Sun2012-10-22-1/+12
| | | | | | | | The QCSP registers are expanded and moved from offset 0 to offset 0x1000 for SoCs with QMan v3. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: expand SERDES reference clock select bitYork Sun2012-10-22-1/+2
| | | | | | | | | | | | | Expand the reference clock select to three bits 000: 100 MHz 001: 125 MHz 010: 156.25MHz 011: 150 MHz 100: 161.1328125 MHz All others reserved Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Fix core cluster PLL calculation for Chassis generation 2York Sun2012-10-22-26/+148
| | | | | | | | | | | | | | | | | | Corenet based SoCs have different core clocks starting from Chassis generation 2. Cores are organized into clusters. Each cluster has up to 4 cores sharing same clock, which can be chosen from one of three PLLs in the cluster group with one of the devisors /1, /2 or /4. Two clusters are put together as a cluster group. These two clusters share the PLLs but may have different divisor. For example, core 0~3 are in cluster 1. Core 4~7 are in cluster 2. Core 8~11 are in cluster 3 and so on. Cluster 1 and 2 are cluster group A. Cluster 3 and 4 are in cluster group B. Cluster group A has PLL1, PLL2, PLL3. Cluster group B has PLL4, PLL5. Core 0~3 may have PLL1/2, core 4~7 may have PLL2/2. Core 8~11 may have PLL4/1. PME and FMan blocks can take different PLLs, configured by RCW. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: check number of coresYork Sun2012-10-22-0/+5
| | | | | | | | Panic if the number of cores is more than CONFIG_MAX_CPUS because it will surely overflow gd structure. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: change RCW MEM_PLL_PLAT for Chassis generation 2York Sun2012-10-22-1/+10
| | | | | | | | Chassis generation 2 has different mask and shift. Use macro instead of magic numbers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Enable L2 at the beginning of U-boot for E6500York Sun2012-10-22-11/+163
| | | | | | | | | | | | | Using E6500 L1 cache as initram requires L2 cache enabled. Add l2-cache cluster enabling. Setup stash id for L1 cache as (coreID) * 2 + 32 + 0 Setup stash id for L2 cache as (cluster) * 2 + 32 + 1 Stash id for L2 is only set for Chassis 2. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Introduce new macros to add and delete TLB entriesYork Sun2012-10-22-179/+130
| | | | | | | These assembly macros simplify codes to add and delete temporary TLB entries. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: Add determining and report IFC frequencyKumar Gala2012-10-22-0/+15
| | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/DPAA: Fix compiling errorYork Sun2012-10-22-2/+0
| | | | | | | | FSL_HW_PORTAL_PME is used even when CONFIG_SYS_DPAA_PME is not defined. Remove the #ifdef. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: Add P5040 processor supportTimur Tabi2012-10-22-0/+372
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the Freescale P5040 SOC, which is similar to the P5020. Features of the P5040 are: Four P5040 single-threaded e5500 cores built Up to 2.4 GHz with 64-bit ISA support Three levels of instruction: user, supervisor, hypervisor CoreNet platform cache (CPC) 2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving support Up to 1600MT/s Memory pre-fetch engine DPAA incorporating acceleration for the following functions Packet parsing, classification, and distribution (FMAN) Queue management for scheduling, packet sequencing and congestion management (QMAN) Hardware buffer management for buffer allocation and de-allocation (BMAN) Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes 20 lanes at up to 5 Gbps Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces Two 10 Gbps Ethernet MACs Ten 1 Gbps Ethernet MACs High-speed peripheral interfaces Two PCI Express 2.0/3.0 controllers Additional peripheral interfaces Two serial ATA (SATA 2.0) controllers Two high-speed USB 2.0 controllers with integrated PHY Enhanced secure digital host controller (SD/MMC/eMMC) Enhanced serial peripheral interface (eSPI) Two I2C controllers Four UARTs Integrated flash controller supporting NAND and NOR flash DMA Dual four channel Support for hardware virtualization and partitioning enforcement Extra privileged level for hypervisor support QorIQ Trust Architecture 1.1 Secure boot, secure debug, tamper detection, volatile key storage Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/p5040ds: add per pci endpoint liodn offset listLaurentiu Tudor2012-10-22-0/+52
| | | | | | | | | | | | | | | | | | | | Add a new device tree property named "fsl,liodn-offset-list" holding a list of per pci endpoint permitted liodn offsets. This property is useful in virtualization scenarios that implement per pci endpoint partitioning. The final liodn of a partitioned pci endpoint is calculated by the hardware, by adding these offsets to pci controller's base liodn, stored in the "fsl,liodn" property of its node. The liodn offsets are interleaved to get better cache utilization. As an example, given 3 pci controllers, the following liodns are generated for the pci endpoints: pci0: 193 256 259 262 265 268 271 274 277 pci1: 194 257 260 263 266 269 272 275 278 pci2: 195 258 261 264 267 270 273 276 279 Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: define SRIO LIODN functions only if SRIO is definedTimur Tabi2012-10-22-1/+11
| | | | | | | | The P5040 does not have SRIO support, so there are no SRIO LIODNs. Therefore, the functions that set the SRIO LIODNs should not be compiled. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: introduce SET_PCI_LIODN_BASE, for setting PCI LIODNsLaurentiu Tudor2012-10-22-1/+8
| | | | | | | | | | | | The liodn for the new PCIE controller included in P5040DS is no longer set through a register in the guts register block but with one in the PCIE register block itself. Update the PCIE CCSR structure to add the new liodn register and add a new dedicated SET_PCI_LIODN_BASE macro that puts the liodn in the correct register. Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: fix Unicode characters in release.STimur Tabi2012-10-22-12/+12
| | | | | | | | Commit 709389b6 unintentionally used the Unicode version of the apostrophy. Replace it with the normal ASCII version. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/srio: Workaround for srio erratrm a004034Liu Gang2012-10-22-0/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Erratum: A-004034 Affects: SRIO Description: During port initialization, the SRIO port performs lane synchronization (detecting valid symbols on a lane) and lane alignment (coordinating multiple lanes to receive valid data across lanes). Internal errors in lane synchronization and lane alignment may cause failure to achieve link initialization at the configured port width. An SRIO port configured as a 4x port may see one of these scenarios: 1. One or more lanes fails to achieve lane synchronization. Depending on which lanes fail, this may result in downtraining from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane). 2. The link may fail to achieve lane alignment as a 4x, even though all 4 lanes achieve lane synchronization, and downtrain to a 1x. An SRIO port configured as a 1x port may fail to complete port initialization (PnESCSR[PU] never deasserts) because of scenario 1. Impact: SRIO port may downtrain to 1x, or may fail to complete link initialization. Once a port completes link initialization successfully, it will operate normally. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Fix USB device-tree fixupramneek mehresh2012-10-22-16/+34
| | | | | | | | | | | | | Fix usb device-tree fixup: - wrong modification of dr_mode and phy_type when "usb1" is not mentioned inside hwconfig string; now allows hwconfig strings like: "usb2:dr_mode=host,phy_type=ulpi" - add warning message for using usb_dr_mode and usb_phy_type env variables (if either is used) Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* P4080/esdhc: make the P4080 ESDHC13 errata workaround conditionalZang Roy-R619112012-10-22-7/+10
| | | | | | | | | | P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the workaround conditional. In formal release document, the errata number should be ESDHC13 instead of ESDHC136. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc mpc85xx: Only clear TSR:WIS in watchdog_reset.Mark Marshall2012-10-22-4/+1
| | | | | | | | | | | | We should only write TSR_WIS to the SPRN_TSR register in reset_85xx_watchdog. The old code would cause the timer interrupt to be acknowledged when the watchdog was reset, and we would then get no more timer interrupts. This bug would affect all mpc85xx boards that have the watchdog enabled. Signed-off-by: Mark Marshall <Mark.Marshall@omicron.at> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mpc85xx: make gpio_direction_output respect valueChris Packham2012-10-22-1/+4
| | | | | | | | | | | | | | Users of familiar with the Linux gpiolib API expect that value parameter to gpio_direction_output reflects the initial state of the output pin. gpio_direction_output was always driving the output low, now it drives it high or low according to the value provided. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc: Change bi_baudrate and global data baudrate to intSimon Glass2012-10-19-2/+2
| | | | | | | These don't need to be longs, so change them. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@ti.com>
* split mpc8xx hooks from cmd_ide.cPavel Herrmann2012-10-17-0/+233
| | | | | | | | | | | | | move most of mpc8xx hooks from cmd_ide.c into ide_preinit() and newly created ide_init_postreset() (invoked after calling ide_reset after ide_preinit), some cleanup to make checkpatch happy, enable IDE init hooks in configs of affected boards. confusingly, these hooks are used by more than just mpc8xx-based boards, and therefore are placed in arch/ppc/lib/ note: checkpatch still emits warnings about using volatile Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
* serial: Use default_serial_puts() in driversMarek Vasut2012-10-17-41/+5
| | | | | | | | | | Replace the in-place ad-hoc implementation of serial_puts() within the drivers with default_serial_puts() call. This cuts down on the code duplication quite a bit. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com>
* mpc82xx: Remove BMW board portStefan Roese2012-10-17-9/+4
| | | | | | | | | | | As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: James F. Dougherty <jfd@broadcom.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Marek Vasut <marex@denx.de>
* usb: lowlevel interface change to support multiple controllersLucas Stach2012-10-15-4/+4
| | | | | | | | | | | Carry an index in the lowlevel usb functions to make specify the respective usb controller. Also pass through an controller struct from lowlevel_init to the creation of the root usb device of this controller. Signed-off-by: Lucas Stach <dev@lynxeye.de> Reviewed-by: Marek Vasut <marex@denx.de>
* ppc4xx: Remove AP1000 board supportStefan Roese2012-10-15-15/+0
| | | | | | | | | As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: James MacAulay <james.macaulay@amirix.com> Acked-by: Marek Vasut <marex@denx.de>
* ppc4xx: Remove ML2 board supportStefan Roese2012-10-15-1/+1
| | | | | | | | | As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Peter De Schrijver <p2@mind.be> Acked-by: Marek Vasut <marex@denx.de>
* ppc4xx: Remove IOP480 supportStefan Roese2012-10-15-400/+2
| | | | | | | | | | Since the IOP480 (PPC401/3 variant from PLX) is only used on 2 boards that are not actively maintained, lets remove support for it completely. This way the ppc4xx code will get a bit cleaner. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu> Acked-by: Marek Vasut <marex@denx.de>
* serial: Remove CONFIG_SERIAL_MULTI from remaining sourcesMarek Vasut2012-10-15-2/+0
| | | | | | | | | | | | Remove the parts depending either on disabled CONFIG_SERIAL_MULTI or ifdefs around CONFIG_SERIAL_MULTI parts since CONFIG_SERIAL_MULTI is now enabled by default. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: Remove CONFIG_SERIAL_MULTI from serial driversMarek Vasut2012-10-15-369/+39
| | | | | | | | | | | | Remove the support for not-CONFIG_SERIAL_MULTI part from serial port drivers and some board files. Since CONFIG_SERIAL_MULTI is now enabled by default, that part is a dead code. Remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into iop480 serial driverMarek Vasut2012-10-15-6/+59
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into iop480 serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the iop480 driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into mpc85xx serial driverMarek Vasut2012-10-15-11/+60
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into mpc85xx serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the mpc85xx driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into mpc8260 serial driversMarek Vasut2012-10-15-22/+120
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into both SCC and SMC mpc8260 serial drivers. These drivers were so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the mpc8260 drivers. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into mpc8220 serial driverMarek Vasut2012-10-15-6/+61
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into mpc8220 serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the mpc8220 driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: powerpc: Implement CONFIG_SERIAL_MULTI into mpc5xx serial driverMarek Vasut2012-10-15-21/+74
| | | | | | | | | | | | | | Implement support for CONFIG_SERIAL_MULTI into mpc5xx serial driver. This driver was so far only usable directly, but this patch also adds support for the multi method. This allows using more than one serial driver alongside the mpc5xx driver. Also, add a weak implementation of default_serial_console() returning this driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: mpc512x: Move serial registration from serial_initialize()Marek Vasut2012-10-15-0/+16
| | | | | | | | | | | | | | | | | | | | | | | Move the registration of serialN_device ports from default serial_initialize() into driver specific function called from serial_initialize(). This slims down the serial_initialize() call to a bare tracker of all possible serial port registration routines in U-Boot. The newly implemented mpc512x_serial_initialize() function, which is implemented inside of the mpc512x serial driver allows encapsulation of serialN_device within the mpc512x serial driver itself. Also, remove the exports of serialN_device from include/serial.h as they are no longer needed. This is simply because the implementation of default_serial_console() is wrapped into the mpx512x serial driver and the default console is picked by CONFIG_SERIAL<N> macro in config file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de>
* serial: mpc8xx: Move serial registration from serial_initialize()Marek Vasut2012-10-15-0/+11
| | | | | | | | | | | | | | | | | | | Move the registration of serial_smc and serial_scc ports from default serial_initialize() into CPU specific function called from serial_initialize(). This slims down the serial_initialize() call to a bare tracker of all possible serial port registration routines in U-Boot. The exports of both serial_scc_device and serial_smc_device can not yet be removed as they are still used in default_serial_console() calls. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Mike Frysinger <vapier@gentoo.org>
* serial: Properly spell out the structure member names of serial_driverMarek Vasut2012-10-15-41/+41
| | | | | | | | | | | | | | | | | Properly spell out the whole structure member names when an initialized varible is instantiated from the struct serial_driver. In case the structure definition for struct serial_driver undergoes reordering, there will be no impact on variables defined based on this structure. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: C Nauman <cnauman@diagraph.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Michal Simek <monstr@monstr.eu>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2012-09-25-926/+1359
|\
| * Revert "powerpc: Fix declaration type for I/O functions"Andy Fleming2012-08-23-10/+10
| | | | | | | | This reverts commit 20959471b5d07fdeb8603b918d80385aa2954711.
| * powerpc/85xx: clear out TLB on bootScott Wood2012-08-23-33/+48
| | | | | | | | | | | | | | | | Instead of just shooting down the entry that covers CCSR, clear out every TLB entry that isn't the one that we're executing out of. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Move HWCONFIG_BUFFER_SIZE into config.hYork Sun2012-08-23-5/+4
| | | | | | | | | | | | | | | | | | | | Before proper environment is setup, we extract hwconfig and put it into a buffer with size HWCONFIG_BUFFER_SIZE. We need to enlarge the buffer to accommodate longer string. Since this macro is used in multiple files, we move it into arch/powerpc/include/asm/config.h. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx DDR: Fix interactive DDR debuggingYork Sun2012-08-23-2/+2
| | | | | | | | | | | | | | | | Add one more argument to call function readline_into_buffer(). Fix print SPD format for negative values. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit v1.1 at 2024-11-09 19:21:56 +0000