summaryrefslogtreecommitdiff
path: root/arch/powerpc/lib
Commit message (Collapse)AuthorAgeLines
* arch/powerpc/lib/bat_rw.c: Fix GCC 4.6 build warningWolfgang Denk2011-11-07-1/+2
| | | | | | | | | | | Fix: bat_rw.c: In function 'write_bat': bat_rw.c:38:6: warning: variable 'batn' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Andy Fleming <afleming@gmail.com>
* arch/powerpc/lib/board.c: fix build warningWolfgang Denk2011-11-07-3/+0
| | | | | | | | Fix: board.c: In function 'board_init_r': board.c:633:8: warning: unused variable 's' [-Wunused-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
* arch/powerpc/lib/board.c: make (mostly) checkpatch-cleanWolfgang Denk2011-11-07-221/+234
| | | | | | | | | | | | | | | | | | CodingStyle cleanup. Accepted (in this cleanup) checkpatch messages: - externs should be avoided (to be cleaned up later) - no spaces at the start of a line (accepted in multi-line #if's) - Macros with complex values (false reports) - do not use assignment in if condition (accepted in one place, where avoiding it would have required an additional level of nesting, resulting in less readable code) Signed-off-by: Wolfgang Denk <wd@denx.de>
* arch/powerpc/lib/board.c: fix build warningWolfgang Denk2011-11-03-1/+3
| | | | | | | | | | | | | | Commit 1272592 "powerpc: Use getenv_ulong() in place of getenv(), strtoul" instroduced a build warning for some PPC systems: board.c: In function 'board_init_r': board.c:626: warning: unused variable 's' Fix it. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de>
* powerpc: Correct build warning introduced by getenv_ulong() patchSimon Glass2011-10-24-3/+7
| | | | | | | Commit 1272592 introduced a warning since the variable 's' is no longer always used, depending on the CONFIG options. Signed-off-by: Simon Glass <sjg@chromium.org>
* powerpc/lib/board.c: Call run_post(POST_ROM) before relocatingBernhard Kaindl2011-10-23-7/+7
| | | | | | | | | | | | | | | | | | | The call to run_post(POST_ROM) which can run the POST memory test is currently called too late when gd has already been copied to DRAM. This results in failure to boot Linux after a POST_ROM memory test tested all RAM while gd was already relocated to DRAM due to gd being overwritten by the POST_ROM memory test. Support this by moving the call to run_post(POST_ROM) to run earlier, before U-Boot has started to move data to DRAM (from late board_init_f to early board_init_f) where DRAM is initialized, but not used yet. This allows that an POST memory test can test the whole DRAM, including the area where the board info struct is located. Signed-off-by: Bernhard Kaindl <bernhard.kaindl@thalesgroup.com> Cc: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
* powerpc: Use getenv_ulong() in place of getenv(), strtoulSimon Glass2011-10-23-25/+8
| | | | | | | This changes the board code to use the new getenv_ulong() function. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stefan Roese <sr@denx.de>
* net: drop !NET_MULTI codeMike Frysinger2011-10-05-2/+0
| | | | | | | | | | | This is long over due. All but two net drivers have been converted, but those have now been dropped. The only thing left to do is actually delete all references to NET_MULTI and code that is compiled when that is not defined. So here we scrub the core code. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Flush cache after the OS image is loaded into the memory.Diana CRACIUN2011-09-05-14/+6
| | | | | | | | | | | | | | | | Since we are loading an executable image into memory we need flush it out of the cache to possible maintain coherence on CPUs with split instruction and data caches. We do this for other executable image loading command. On PowerPC once we do this we no longer need to explicitly flush the dcache on multi-core systems in the BOOTM_STATE_OS_PREP phase. We now treat the BOOTM_STATE_OS_PREP as a no-op to maintain backwards compatibility with the bootm subcommand. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* hwmon: do not init sensors on startupHeiko Schocher2011-08-04-3/+0
| | | | | | | | | | | | | | | | | The U-Boot Design Principles[1] clearly say: Initialize devices only when they are needed within U-Boot, i.e. don't initialize the Ethernet interface(s) unless U-Boot performs a download over Ethernet; don't initialize any IDE or USB devices unless U-Boot actually tries to load files from these, etc. (and don't forget to shut down these devices after using them - otherwise nasty things may happen when you try to boot your OS). So, do not initialize and read the sensors on startup. Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Holger Brunck <holger.brunck@keymile.com>
* powerpc/85xx: verify the device tree before booting LinuxTimur Tabi2011-07-29-0/+21
| | | | | | | | | | | | | | | Introduce ft_verify_fdt(), a function that is called after the device tree has been fixed up, that displays warning messages if there is a mismatch between the physical addresses of some devices that U-Boot has configured with what the device tree says the addresses are. This is a particular problem when booting a 36-bit device tree from a 32-bit U-Boot (or vice versa), because the physical address of CCSR is wrong in the device tree. When the operating system boots, no messages are displayed, so the user generally has no idea what's wrong. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Fix setting of EPAPR_MAGIC valueKumar Gala2011-07-29-1/+1
| | | | | | | | Had a typo in the ifdef for 85xx, should be CONFIG_MPC85xx for it to get triggered. Was pull in the non-BookE magic number. Reported-by: John Cortell Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Timer: Remove reset_timer() for non-Nios2 archesGraeme Russ2011-07-26-5/+0
|
* Timer: Remove set_timer completelyGraeme Russ2011-07-26-7/+0
|
* powerpc: Fix device tree padding associated with ramdiskKumar Gala2011-07-26-1/+3
| | | | | | | | | | | | | | | | | When booting with a ramdisk we bump the amount of memory reserved for the device tree by FDT_RAMDISK_OVERHEAD. However we did not increase the actual size in the device tree blob to match. Its possible on boundary cases that we dont have enough memory according to the device tree blob and get errors like: WARNING: could not set linux,initrd-end FDT_ERR_NOSPACE We can easily fix this by setting the device tree size at the same time we bump the amount of memory reserved for the device tree. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
* mpc832x: add support for the mpc8321 based suvd3 boardHeiko Schocher2011-04-30-1/+1
| | | | | | | | | | | | | | | | | | | | - serial console on UART1 - Ethernet RMII over UCC4 - PHY SMSC LAN8700 - 64MB Flash - 128 MB DDR2 RAM - I2C - bootcount This board is similiar to the kmeter1 (8360) board, so common config options are extracted into the include/configs/km83xx-common.h file. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2011-04-27-0/+4
|\
| * Don't grab memory for LCD if FB address is definedMinkyu Kang2011-04-27-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | If FB address is defined specific address then don't grab memory for LCD Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Albert Aribaud <albert.aribaud@free.fr> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Kumar Gala <kumar.gala@freescale.com>
* | Respect memreserve regions specified in the device treeGrant Likely2011-04-25-0/+4
| | | | | | | | | | | | | | | | If a regions is reserved in the fdt, then it should not be used. Add the memreserve regions to the lmb so that u-boot doesn't use them to store the initrd. Signed-off-by: Grant Likely <grant.likely@linaro.org>
* | Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZGrant Likely2011-04-25-2/+2
| | | | | | | | | | | | | | | | | | The previous patch makes u-boot use the full accessible size of ram as the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined, which means boot_relocate_fdt() can be changed to depend solely on CONFIG_OF_LIBFDT. Signed-off-by: Grant Likely <grant.likely@linaro.org>
* | Default to bootm_size() when CONFIG_SYS_BOOTMAPSZ is not definedGrant Likely2011-04-25-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds a function getenv_bootm_mapsize() for obtaining the size of the early mapped region accessible by the kernel during early boot. It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined, defaults to getenv_bootm_size(), which in turn defaults to the size of RAM. getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize" environmental variable. Signed-off-by: Grant Likely <grant.likely@linaro.org>
* | Stop passing around bootmem_base value.Grant Likely2011-04-25-6/+3
|/ | | | | | | | | | For the calls to boot_relocate_fdt(), boot_get_cmdline(), and boot_get_kbd(), the value of bootmem_base is always obtained by calling getenv_bootm_low(). Since the value always comes from the same source, the calling signature for those functions can be simplified by making them call getenv_bootm_low() directly. Signed-off-by: Grant Likely <grant.likely@linaro.org>
* powerpc: Add cpu_secondary_init_r to allow for initialization post env setupKumar Gala2011-04-04-0/+14
| | | | | | | | | | | | | We can simplify some cpu/SoC level initialization by moving it to be after the environment and non-volatile storage is setup as there might be dependancies on such things in various boot configurations. For example for FSL SoC's with QE if we boot from NAND we need it setup to extra the ucode image to initialize the QE. If we always do this after environment & non-volatile storage is working we can have the code be the same regardless of NOR, NAND, SPI, MMC boot. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc: Move cpu specific lmb reserve to arch_lmb_reserveKumar Gala2011-04-04-0/+5
| | | | | | | | We've been utilizing board_lmb_reserve to reserve the boot page for MP systems. We can just move this into arch_lmb_reserve for 85xx & 86xx systems rather than duplicating in each board port. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* rename _end to __bss_end__Po-Yu Chuang2011-03-27-2/+2
| | | | | | | Currently, _end is used for end of BSS section. We want _end to mean end of u-boot image, so we rename _end to __bss_end__ first. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
* Replace "FLASH" strings with "Flash" or "flash"Peter Tyser2011-01-19-1/+1
| | | | | | | | There's no compelling reason to have the output on bootup or the "flinfo" command print "flash" in uppercase, so use the proper case where appropriate. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* powerpc: fix register usage in some inline assembly codeTimur Tabi2010-12-17-11/+19
| | | | | | | In some usages of inline assembly, hard-coded registers were specified when a scratch register should have been used instead. Signed-off-by: Timur Tabi <timur@freescale.com>
* Merge branch 'master' of ../master into nextWolfgang Denk2010-12-16-0/+11
|\
| * powerpc/85xx: Introduce CONFIG_SYS_EXTRA_ENV_RELOCKumar Gala2010-11-30-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some systems need to relocate the env_addr pointer early because the location it points to will get invalidated before env_relocate is called. One example is on systems that might use a L2 or L3 cache in SRAM mode and initialize that cache from SRAM mode back to being a cache in cpu_init_r. We set this on the 85xx boards that have support for NAND, SPI, or SDHC/MMC boot support as they use a secondary cache in SRAM mode and need the env_addr pointer relocated since we change from SRAM to normal cache mode in cpu_init_r. Also removed CONFIG_SYS_SPL as its not used anywhere. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | do_reset: unify duplicate prototypesMike Frysinger2010-11-28-1/+0
|/ | | | | | | The duplication of the do_reset prototype has gotten out of hand, and they're not all in sync. Unify them all in command.h. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* WINBOND_83C553: enable only on boards that actually use it.Wolfgang Denk2010-11-26-1/+1
| | | | | | | | | | | | | | | | | | | | So far, only the BAB7xx board would call the initialise_w83c553f() function for the WINBOND 83C553 chip, even though some other boards (HIDDEN_DRAGON, Sandpoint8240, Sandpoint8245) enabled it in their board configuration. These boards were also missing other config settings needed for that, which resulted in build errors like this: drivers/pci/libpci.o:(.got2+0x84): undefined reference to `ide_bus_offset' Switch arch/powerpc/lib/board.c to call initialise_w83c553f() not on a per-board base, but when a WINBOND_83C553 in enabled in a configuration (like BAB7xx), and disable it in the boards that had this set so far. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Yusdi Santoso <yusdi_santoso@adaptec.com> Cc: Jim Thompson <jim@musenki.com> Acked-by: Stefan Roese <sr@denx.de>
* Switch from archive libraries to partial linkingSebastien Carlier2010-11-17-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
* ppc: Don't initialize write protected NOR flashesJohn Schmoller2010-10-20-1/+15
| | | | | | | | | | | | If a NOR flash is write protected it can not be initialized/detected so add the ability for boards to skip NOR initialization on bootup. A board can skip NOR initialization by implementing the board_flash_wp_on() function. Signed-off-by: John Schmoller <jschmoller@xes-inc.com> Signed-off-by: Peter Tyser <ptyser@xes-inc.com> CC: sr@denx.de Acked-by: Stefan Roese <sr@denx.de>
* powerpc: Cleanup BOOTFLAG_* referencesPeter Tyser2010-10-18-2/+0
| | | | | | | | | | | | Now that warm booting is not supported, there isn't a need for the BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them. Note that this change makes the board info bd_bootflags field useless. It will always be set to 0, but we leave it around so that we don't break the board info structure that some OSes are expecting to be passed from U-Boot. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk2010-10-18-1/+1
| | | | | | | | | | | | The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
* ppc: Conditionally compile bat_rw.cPeter Tyser2010-10-13-1/+1
| | | | | | | Only a few PPC boards actually use the common BAT manipulation functions, so only compile it for them. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* powerpc: Zero out board info struct on bootupPeter Tyser2010-10-12-16/+1
| | | | | | | This puts the board info struct in a known state and allows the removal of other code which initialized board info fields to 0. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* PowerPC: change board specific early pci_init() into generic.Andre Schwarz2010-10-06-5/+4
| | | | Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
* PCU_E: remove code for yet another corpseWolfgang Denk2010-10-06-2/+2
| | | | | | | The PCU_E board has long reached EOL, and support for it is no longer relevant in current versions of U-Boot. Remove it. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Remove unused CONFIG_SERIAL_SOFTWARE_FIFO featureStefan Roese2010-09-23-7/+0
| | | | | | | | | This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO feature from U-Boot. It has only been implemented for PPC4xx and was not used at all. So let's remove it and make the code smaller and cleaner. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* common: move TOTAL_MALLOC_LEN to include/common.hHeiko Schocher2010-09-19-10/+0
| | | | | | | Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Heiko Schocher <hs@denx.de>
* Cleanup use of CONFIG_SYS_SRAM_BASE and CONFIG_SYS_SRAM_SIZEWolfgang Denk2010-09-19-6/+3
| | | | | | | | | | | | | | | | | | | | | | Traditionally many boards used local definitions for SRAM base address and size (like SRAM_BASE, SRAM_LEN and/or SRAM_SIZE), while the (now) "official" names are CONFIG_SYS_SRAM_BASE and CONFIG_SYS_SRAM_SIZE. The corresponding code in arch/powerpc/lib/board.c was board specific, and has never actually been maintained well. Replace this by feature- specific code and adapt the boards that actually use this. NOTE: there is still a ton of boards using the old #defines, which therefor contain incorrect values in bi_sramstart and bi_sramsize. All respective board maintainers are requested to clean up their respective configurations. Thanks. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Josef Wagner <Wagner@Microsys.de> Cc: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de>
* Save environment data to mmc.Terry Lv2010-09-19-6/+11
| | | | | | | | This patch is to save environment data to mmc card. It uses interfaces defined in generic mmc. Signed-off-by: Terry Lv <r65388@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* fdt relocate: have more attention to use a bootmap or notStephan Linz2010-08-08-2/+2
| | | | | | | | | | | | | | | | Platforms with flat device tree support can use a bootmap to relocate the fdt_blob. This is not a must. That's why the relocation function boot_relocate_fdt() should be use only if CONFIG_OF_LIBFDT was defined together with CONFIG_SYS_BOOTMAPSZ (see common/cmd_bootm.c). On MicroBlaze platforms there is no need to use a bootmap to relocate a fdt blob. So we need a more precise focus on the compilation and usage of boot_relocate_fdt(). In general it is valid to exclude the function boot_relocate_fdt() if the bootmap size CONFIG_SYS_BOOTMAPSZ is not defined. Signed-off-by: Stephan Linz <linz@li-pro.net>
* Rename getenv_r() into getenv_f()Wolfgang Denk2010-08-04-3/+3
| | | | | | | | | | | | | | | | | | | While running from flash, i. e. before relocation, we have only a limited C runtime environment without writable data segment. In this phase, some configurations (for example with environment in EEPROM) must not use the normal getenv(), but a special function. This function had been called getenv_r(), with the idea that the "_r" suffix would mean the same as in the _r_eentrant versions of some of the C library functions (for example getdate vs. getdate_r, getgrent vs. getgrent_r, etc.). Unfortunately this was a misleading name, as in U-Boot the "_r" generally means "running from RAM", i. e. _after_ relocation. To avoid confusion, rename into getenv_f() [as "running from flash"] Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* Make sure that argv[] argument pointers are not modified.Wolfgang Denk2010-07-04-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The hush shell dynamically allocates (and re-allocates) memory for the argument strings in the "char *argv[]" argument vector passed to commands. Any code that modifies these pointers will cause serious corruption of the malloc data structures and crash U-Boot, so make sure the compiler can check that no such modifications are being done by changing the code into "char * const argv[]". This modification is the result of debugging a strange crash caused after adding a new command, which used the following argument processing code which has been working perfectly fine in all Unix systems since version 6 - but not so in U-Boot: int main (int argc, char **argv) { while (--argc > 0 && **++argv == '-') { /* ====> */ while (*++*argv) { switch (**argv) { case 'd': debug++; break; ... default: usage (); } } } ... } The line marked "====>" will corrupt the malloc data structures and usually cause U-Boot to crash when the next command gets executed by the shell. With the modification, the compiler will prevent this with an error: increment of read-only location '*argv' N.B.: The code above can be trivially rewritten like this: while (--argc > 0 && **++argv == '-') { char *arg = *argv; while (*++arg) { switch (*arg) { ... Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' into nextWolfgang Denk2010-06-30-4/+83
|\
| * MPC512x: workaround data corruption for unaligned local bus accessesWolfgang Denk2010-06-29-4/+83
| | | | | | | | | | | | | | | | | | | | | | Commit 460c2ce3 "MPC5200: workaround data corruption for unaligned local bus accesses" fixed the problem for MPC5200 only, but MPC512x is affected as well, so apply the same fix here, too. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* | powerpc/bootcount: Add bootcount support for MPC512xMichael Weiss2010-06-29-0/+5
|/ | | | | | | This also uses the breadcrumb register as on MPC5200. Signed-off-by: Michael Weiss <michael.weiss@ifm.com> Signed-off-by: Detlev Zundel <dzu@denx.de>
* MPC5200: workaround data corruption for unaligned local bus accessesWolfgang Denk2010-06-23-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MPC5200 has a nasty problem that will cause silent data corruption when performing unaligned 16 or 32 byte accesses when reading from the local bus - typically this affects reading from flash. The problem can be easily shown: => md fc0c0000 10 fc0c0000: 323e4337 01626f6f 74636d64 3d72756e 2>C7.bootcmd=run fc0c0010: 206e6574 5f6e6673 00626f6f 7464656c net_nfs.bootdel fc0c0020: 61793d35 00626175 64726174 653d3131 ay=5.baudrate=11 fc0c0030: 35323030 00707265 626f6f74 3d656368 5200.preboot=ech => md fc0c0001 10 fc0c0001: 65636801 00000074 0000003d 00000020 ech....t...=... fc0c0011: 0000005f 00000000 00000074 00000061 ..._.......t...a fc0c0021: 00000000 00000064 00000065 00000035 .......d...e...5 fc0c0031: 00000000 00000062 0000003d 0000006f .......b...=...o => md.w fc0c0001 10 fc0c0001: 0000 3701 0000 6f74 0000 643d 0000 6e20 ..7...ot..d=..n fc0c0011: 0000 745f 0000 7300 0000 6f74 0000 6c61 ..t_..s...ot..la This commit implements a workaround at least for the most blatant problem: using memcpy() from NOR flash. We rename the assembler routine into __memcpy() and provide a wrapper, which will use a byte-wise copy loop for unaligned source or target addresses when reading from NOR flash, and branch to the optimized __memcpy() in all other cases, thus minimizing the performance impact. Tested on lite5200b and TQM5200S. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
generated by cgit v1.1 at 2024-11-09 15:29:26 +0000