summaryrefslogtreecommitdiff
path: root/arch/powerpc/include
Commit message (Collapse)AuthorAgeLines
* powerpc/mpc85xx: work around erratum A-006593Scott Wood2013-06-20-0/+2
| | | | | | | | | | | | Erratum A-006593 is "Atomic store may report failure but still allow the store data to be visible". The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit 21 to 1'b1. This may have a small impact on synthetic write bandwidth benchmarks but should have a negligible impact on real code." Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* fsl_ifc: add support for different IFC bank countMingkai Hu2013-06-20-31/+68
| | | | | | | | | | | | Calculate reserved fields according to IFC bank count 1. Move csor_ext register behind csor register and fix res offset 2. Move ifc bank count to config_mpc85xx.h to support 8 bank count 3. Guard fsl_ifc.h with CONFIG_FSL_IFC macro to eliminate the compile error on some devices that does not have IFC controller. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/t4qds: Slave module for boot from SRIO and PCIELiu Gang2013-06-20-0/+1
| | | | | | | | | | | | | | | | | | | | | When a T4 board boots from SRIO or PCIE, it needs to finish these processes: 1. Set all the cores in holdoff status. 2. Set the boot location to one PCIE or SRIO interface by RCW. 3. Set a specific TLB entry for the boot process. 4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot. 5. Set a specific TLB entry in order to fetch ucode and ENV from master. 6. Set a LAW entry with the TargetID one of the PCIE ports for ucode and ENV. 7. Slave's u-boot image should be generated specifically by make xxxx_SRIO_PCIE_BOOT_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. For more information about the feature of Boot from SRIO/PCIE, please refer to the document doc/README.srio-pcie-boot-corenet. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/b4860qds: Slave module for boot from SRIO and PCIELiu Gang2013-06-20-0/+1
| | | | | | | | | | | | | | | | | | | | | | When a b4860qds board boots from SRIO or PCIE, it needs to finish these processes: 1. Set all the cores in holdoff status. 2. Set the boot location to one PCIE or SRIO interface by RCW. 3. Set a specific TLB entry for the boot process. 4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot. 5. Set a specific TLB entry in order to fetch ucode and ENV from master. 6. Set a LAW entry with the TargetID one of the PCIE ports for ucode and ENV. 7. Slave's u-boot image should be generated specifically by make xxxx_SRIO_PCIE_BOOT_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. For more information about the feature of Boot from SRIO/PCIE, please refer to the document doc/README.srio-pcie-boot-corenet. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/boot: Change the macro of Boot from SRIO and PCIE master moduleLiu Gang2013-06-20-4/+0
| | | | | | | | | | | | | | | | | Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable the master module of Boot from SRIO and PCIE on a platform. But this is not a silicon feature, it's just a specific booting mode based on the SRIO and PCIE interfaces. So it's inappropriate to put the macro into the file arch/powerpc/include/asm/config_mpc85xx.h. Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to "CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros in configuration header file of each board which can support the master module of Boot from SRIO and PCIE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* 85xx: Change case of MPC85XX_PORBMSR_ROMLOC_SHIFTAndy Fleming2013-06-20-1/+1
| | | | | | | All the other constants use lowercase 'x' in "MPC85xx", so we duplicate that here. Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/BSC9132: Add IFC bank countYork Sun2013-06-20-0/+1
| | | | | | | BSC9132 has 3 IFC banks. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* board/bsc9131rdb: Add DSP side tlb and lawsPriyanka Jain2013-06-20-0/+7
| | | | | | | | | | | | | | | BSC9131RDB is a Freescale Reference Design Board for BSC9131 SoC which is a integrated device that contains one powerpc e500v2 core and one DSP starcore. To support DSP starcore -Creating LAW and TLB for DSP-CCSR space. -Creating LAW for DSP-core subsystem M2 memory Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc: fix 8xx and 82xx type-punning warnings with GCC 4.7Scott Wood2013-06-11-8/+18
| | | | | | | | | | | C99's strict aliasing rules are insane to use in low-level code such as a bootloader, but as Wolfgang has rejected -fno-strict-aliasing in the past, add a union so that 16-bit accesses can be performed. Compile-tested only. Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-05-30-323/+162
|\ | | | | | | | | | | Conflicts: common/cmd_fpga.c drivers/usb/host/ohci-at91.c
| * SECURE BOOT - Removed deletion of TLB entries codeRuchika Gupta2013-05-24-10/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | Boot ROM code creates TLB entries for 3.5G space before entering the u-boot. Earlier we were deleting these entries after early initialization of CPU. In recent past, code has been added to invalidate all these entries before relocation of u-boot code. So this code to delete TLB entries after CPU initialization is no longer required. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Acked-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/b4860qds: Add LAW Target ID and Create LAW entry for MapleShaveta Leekha2013-05-24-0/+2
| | | | | | | | | | Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/B4: Merge B4420 and B4860 in config_mpc85xx.hPoonam Aggrwal2013-05-24-23/+11
| | | | | | | | | | | | | | | | | | | | | | | | B4420 is a subset of B4860. Merge them in config_mpc85xx.h to simplify the defines. - Removed #define CONFIG_SYS_FSL_NUM_CLUSTERS as this is used nowhere. - defined CONFIG_SYS_NUM_FM1_10GEC to 0 for B4420 as it does not have 10G. Also move CONFIG_E6500 out of B4860QDSds.h into config_mpc85xx.h. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/chassis2: Change core numbering schemeYork Sun2013-05-24-16/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To align with chassis generation 2 spec, all cores are numbered in sequence. The cores may reside across multiple clusters. Each cluster has zero to four cores. The first available core is numbered as core 0. The second available core is numbered as core 1 and so on. Core clocks are generated by each clusters. To identify the cluster of each core, topology registers are examined. Cluster clock registers are reorganized to be easily indexed. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Add T1040 and variant SoCsYork Sun2013-05-24-0/+45
| | | | | | | | | | | | | | | | | | T1040 and variants have e5500 cores and are compliant to QorIQ Chassis Generation 2. The major difference between T1040 and its variants is the number of cores and the number of L2 switch ports. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/T4160: Merge T4160 and T4240 in config_mpc85xx.hYork Sun2013-05-24-32/+10
| | | | | | | | | | | | | | | | T4160 is a subset of T4240. Merge them in config_mpc85xx.h to simplify the defines. Also move CONFIG_E6500 out of t4qds.h into config_mpc85xx.h. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * Add e6500 L2 replacement policy selectionJames Yang2013-05-24-0/+9
| | | | | | | | | | | | | | This is compile-time config. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xxTom Rini2013-05-15-15/+98
| |\
| | * powerpc/85xx: fix build error introduced by serdes_get_prtclShengzhou Liu2013-05-14-1/+0
| | | | | | | | | | | | | | | | | | | | | Removed unused declare serdes_get_prtcl() which was no longer needed. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| | * t4240qds/eth: fixup ethernet for t4240qdsShengzhou Liu2013-05-14-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1, Implemented board_ft_fman_fixup_port() to fix port for kernel. 2, Implemented fdt_fixup_board_enet() to fix node status of different slots and interfaces. 3, Adding detection of slot present for XGMII interface. 4, There is no PHY for XFI, so removed related phy address settings. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| | * powerpc/mpc85xx: Add T4160 SoCYork Sun2013-05-14-2/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T4160 SoC is low power version of T4240. The T4160 combines eight dual threaded Power Architecture e6500 cores and two memory complexes (CoreNet platform cache and DDR3 memory controller) with the same high-performance datapath acceleration, networking, and peripheral bus interfaces. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| | * T4/USB: Add USB 2.0 UTMI dual phy supportRoy Zang2013-05-14-2/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T4240 internal UTMI phy is different comparing to previous UTMI PHY in P3041. This patch adds USB 2.0 UTMI Dual PHY new memory map and enable it for T4240. The phy timing is very sensitive and moving the phy enable code to cpu_init.c will not work. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| | * powerpc/mpc85xx: Update corenet global utility block registersYork Sun2013-05-14-11/+10
| | | | | | | | | | | | | | | | | | | | | | | | Fix ccsr_gur for corenet platform. Remove non-exist registers. Add fuse status register. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| | * powerpc/mpc85xx: Add definitions for HDBCR registersAndy Fleming2013-05-14-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | Makes it a bit easier to see if we've properly set them. While we're in there, modify the accesses to HDBCR0 and HDBCR1 to actually use those definitions. Signed-off-by: Andy Fleming <afleming@freescale.com>
| * | Power: remove support for Freescale MPC8220Wolfgang Denk2013-05-15-260/+0
| |/ | | | | | | | | | | | | | | | | | | The Freescale MPC8220 Power Architecture processors have long reached EOL; Freescale does not even list these any more on their web site. Remove the code to avoid wasting maitaining efforts on dead stuff. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Andy Fleming <afleming@gmail.com>
* | Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-05-11-0/+2
|\ \ | |/ |/| | | | | | | Conflicts: drivers/mtd/nand/mxc_nand_spl.c include/configs/m28evk.h
| * Add fsl_iim driverBenoît Thébaudeau2013-04-28-0/+2
| | | | | | | | | | | | Add a fsl_iim driver common to i.MX and MPC. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | powerpc/mpc85xx: Extend workaround for erratum DDR_A003 to other SoCsYork Sun2013-05-02-0/+3
| | | | | | | | | | | | | | Erratum DDR_A003 applies to P5020, P3041, P4080, P3060, P2041, P5040. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/mpc85xx:IFC Errata A003399 is not valid for BSC913xPrabhakar Kushwaha2013-05-02-2/+0
| | | | | | | | | | | | | | | | As per Errata list of BSC9131 and BSC9132, IFC Errata A003399 is no more valid. So donot compile its workaround. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/85xx: Add workaround for errata USB-14 (enable on P204x/P3041/P50x0)Xulei2013-05-02-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal multi-bit ECC errors, which has impact on performance, so software should disable all ECC reporting from USB1 and USB2. In formal release document, the errata number should be USB14 instead of USB138. Signed-off-by: xulei <Lei.Xu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: xulei <B33228@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | fman/mEMAC: set SETSP bit in IF_MODE regisgter for RGMII speedZang Roy-R619112013-05-02-0/+4
| | | | | | | | | | | | | | | | | | | | Some legacy RGMII phys don't have in band signaling for the speed information. so set the RGMII MAC mode according to the speed got from PHY. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Reported-by: John Traill <john.traill@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/b4860: Adding workaround errata A-005871Shengzhou Liu2013-05-02-0/+2
| | | | | | | | | | | | | | | | Per the latest errata updated, B4860/B4420 Rev 1.0 has also errata A-005871, so adding define A-005871 for B4 SoCs. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc/b4: Fix the wrong register offset of B4 PCIE moduleLiu Gang2013-05-02-1/+2
|/ | | | | | | | | | | | B4420/B4860 PCIE can not work because of the wrong definition of the PCIE register offset in the file: arch/powerpc/include/asm/immap_85xx.h Add the judgement of B4420/B4860 to make the register offset to: #define CONFIG_SYS_MPC85xx_PCIE1_OFFSET 0x200000 Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* ppc: Enable generic board supportSimon Glass2013-03-15-0/+7
| | | | | | | This enables generic board support so that ppc boards can define CONFIG_SYS_GENERIC_BOARD. Signed-off-by: Simon Glass <sjg@chromium.org>
* Introduce generic link section.h symbol filesSimon Glass2013-03-15-0/+27
| | | | | | | | | | | | | | | | | | We create a separate header file for link symbols defined by the link scripts. It is helpful to have these all in one place and try to make them common across architectures. Since Linux already has a similar file, we bring this in even though many of the symbols there are not relevant to us. Each architecture has its own asm/sections.h where symbols specifc to that architecture can be added. For now everything except AVR32 just includes the generic header. One change is needed in arch/avr32/lib/board.c to make this conversion work. Reviewed-by: Tom Rini <trini@ti.com> (version 5) Signed-off-by: Simon Glass <sjg@chromium.org>
* Replace __bss_end__ with __bss_endSimon Glass2013-03-15-1/+1
| | | | | | | | | | | | | Note this is a tree-wide change affecting multiple architectures. At present we use __bss_start, but mostly __bss_end__. This seems inconsistent and in a number of places __bss_end is used instead. Change to use __bss_end for the BSS end symbol throughout U-Boot. This makes it possible to use the asm-generic/sections.h file on all archs. Signed-off-by: Simon Glass <sjg@chromium.org>
* mpc512x: Adjust the DRAM init sequence to the datasheet specAnatolij Gustschin2013-03-09-0/+1
| | | | | | | | Do maintain a 200 usecs period of stable power and clock before asserting the CKE signal and sending commands, have at least 200 DRAM clock cycles pass after initialization before data access. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* mpc512x: add ifm ac14xx boardAnatolij Gustschin2013-03-09-0/+13
| | | | | | | | Add new mpc5121e based ac14xx board and a new pinmux config function for setting individual pinmux bit groups. This function is used in ac14xx board code. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* mpc512x: allow configuring board specific IPS dividerAnatolij Gustschin2013-03-09-0/+2
| | | | | | | Boards may define own IPS divider in the config file if the default IPS divider doesn't fit their needs. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* mpc512x: optionally configure DIU, LPC and NFC devidersAnatolij Gustschin2013-03-09-0/+6
| | | | | | | If a board config file defines DIU, LPC and NFC deviders, configure them in the SCFR1 register. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* powerpc: Use generic global_dataSimon Glass2013-02-04-46/+1
| | | | | | Move powerpc over to use generic global_data. Signed-off-by: Simon Glass <sjg@chromium.org>
* ppc: arm: Move sdhc_clk into arch_global_dataSimon Glass2013-02-04-3/+3
| | | | | | | This is used by both powerpc and arm, but I think it still qualifies as architecture-specific. Signed-off-by: Simon Glass <sjg@chromium.org>
* ppc: Move kbd_status to arch_global_dataSimon Glass2013-02-04-3/+3
| | | | | | Move this field into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org>
* ppc: Move wdt_last to arch_global_dataSimon Glass2013-02-04-3/+3
| | | | | | Move this field into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org>
* ppc: Move fpga_state to arch_global_dataSimon Glass2013-02-04-3/+3
| | | | | | Move this field into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org>
* ppc: Remove console_addr from global dataSimon Glass2013-02-04-6/+0
| | | | | | This does not appear to be used, so punt it. Signed-off-by: Simon Glass <sjg@chromium.org>
* ppc: Move mirror_hack to arch_global_dataSimon Glass2013-02-04-3/+3
| | | | | | Move this field into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org>
* arm: Move uart_clk to arch_global_dataSimon Glass2013-02-04-3/+3
| | | | | | Move this field into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org>
* ppc: Move dp_alloc_base, dp_alloc_top to arch_global_dataSimon Glass2013-02-04-4/+4
| | | | | | Move these fields into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org>
* ppc: Move arbiter fields to arch_global_dataSimon Glass2013-02-04-4/+4
| | | | | | | Move arbiter_event_attributes and arbiter_event_address into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-08-24 20:57:15 +0000