summaryrefslogtreecommitdiff
path: root/arch/powerpc/cpu
Commit message (Collapse)AuthorAgeLines
* powerpc/mpc85xx: Add clear_ddr_tlbs functionBecky Bruce2011-07-22-11/+32
| | | | | | | | | | | This is useful when we just want to wipe out the TLBs. There's currently a function that resets the ddr tlbs to a different value; it is changed to utilize this function. The new function can be used in conjunction with setup_ddr_tlbs() for a board to temporarily map/unmap the DDR address range as needed. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fman: insert the Fman firmware into the device treeTimur Tabi2011-07-22-0/+123
| | | | | | | | | | | | The Fman device tree node binding allows for the entire Fman firmware binary data to be embedded in the device tree. This eliminates the need to have NOR flash mapped to Linux just so that the Fman driver can see the firmware. The location of the Fman firmware is taken from the 'fman_ucode' environment variable. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: add support the ePAPR "phandle" propertyTimur Tabi2011-07-22-2/+4
| | | | | | | | | | | The ePAPR specification says that phandle properties should be called "phandle", and not "linux,phandle". To facilitate the migration from "linux,phandle" to "phandle", we update fdt_qportal() to use the new function, fdt_create_phandle(). This function abstracts the creation of phandle properties. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Fix detection of P1017EKumar Gala2011-07-17-1/+1
| | | | | | Had a typo such that P1017E would not be detected correctly. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: remove SERDES4 soft-reset work-aroundTimur Tabi2011-07-11-22/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some P4080 rev1 errata work-arounds, notably erratum SERDES4, required a bank soft-reset after the bank was configured and enabled, even though enabling a bank causes it to reset. Because the reset was required for multiple errata, it was not properly enclosed in an #ifdef, and so was not removed with all the other rev1 errata work-arounds. Erratum SERDES-8 says that the clocks for bank 3 needs to be enabled if bank 2 is enabled, but this was not being done for SERDES protocols 0xF and 0x10. The bank reset also happened to enable bank 3 (apparently an undocumented feature). Simply removing the reset breaks these two protocols. It turns out that every time we call enable_bank(), we do want at least one lane of the bank enabled, either because the bank is supposed to be enabled, or because we need the clock from that bank enabled. For erratum SERDES-A001, we don't want to modify srds_lpd_b[] when we call enable_bank(), because that array is used elsewhere to determine if the bank is available. Note that the side effect of these changes is that the work-arounds for these two errata are now linked. Specifically, if SERDES-A001 is enabled, then we need SERDES-8 enabled as well. Because this was the only SERDES bank soft-reset, there is no need to implement a work-around for erratum SERDES-A003. Also fix an off-by-one error in a printf(). Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Ed Swarthout <swarthou@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc8xxx: Allow override DDR read-to-write turnaround timeYork Sun2011-07-11-0/+3
| | | | | | | Add this option to allow boards to override the default read-to-write turnaround time for better performance. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/8xxx: Update USB mode device tree fixupRamneek Mehresh2011-07-11-12/+65
| | | | | | | | | | | | Modify support for USB mode fixup: - Add common support for USB mode and phy type device tree fix-up for all USB controllers mentioned in hwconfig string - Fetch USB mode and phy type via hwconfig; if not defined in hwconfig, then fetch them from env Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc8xxx: fix DDR data width checkingYork Sun2011-07-11-8/+27
| | | | | | | | | Checking width before setting DDR controller. SPD for DDR1 and DDR2 has data width and primary sdram width. The latter one has different meaning for DDR3. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc8xxx: Adding fallback to raw timing on supported boardsYork Sun2011-07-11-0/+8
| | | | | | | | In case of empty SPD or checksum error, fallback to raw timing on supported boards. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc8xxx: Enable calculation for fixed DDR chipsYork Sun2011-07-11-3/+33
| | | | | | | | | | We used to have fixed parameters for soldered DDR chips. This patch introduces CONFIG_SYS_DDR_RAW_TIMING to enable calculation based on timing data from DDR chip datasheet, implemneted in board-specific files or header files. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc8xxx: Add 16-bit support for DDR3York Sun2011-07-11-2/+15
| | | | | | | | Add support for 16-bit DDR bus. Also deal with system using 64- and 32-bit DDR devices. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc8xxx: check SPD length before using part numberYork Sun2011-07-11-1/+2
| | | | | | | | Only use DDR DIMM part number if SPD has valid length, to prevent from display garbage in case SPD doesn't cover these fields. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc8xxx: adjust DDR burst length and chop accroding to sdram widthYork Sun2011-07-11-4/+20
| | | | | | | | If the bus width is 32-bit, burst chop should be disabled and burst length should be 8. Read from SPD or other source to determine the width. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add P2041 processor supportKumar Gala2011-07-11-0/+8
| | | | | | The P2041 is similar to P2040, however has a 10G port and backside L2 Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/p2040: Add various p2040 specific informationMingkai Hu2011-07-11-0/+133
| | | | | | | | | | | Add P2040 SoC specific information: * LIODN setup * Portal configuration * etc Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Fix compile errors if CONFIG_SYS_DPAA_QBMAN isn't setKumar Gala2011-07-11-13/+22
| | | | | | | | | | | Add ifdef protection for qp_info and liodn associated with Q/BMan. Also rearrange setting of _tbl_sz variables to utilize existing ifdef protection for things like FMAN. Also add protection around setup_portals() call in corenet_ds board code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Fix compile errors if CONFIG_SYS_{BR,OR}0_PRELIM aren't setKumar Gala2011-07-11-0/+2
| | | | | | | | Add ifdef protection in LBC code to handle the case in which CONFIG_SYS_BR0_PRELIM and CONFIG_SYS_OR0_PRELIM arent defined for a build. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* MPC83XX: Fix PCI express clock setupBill Cook2011-07-06-2/+4
| | | | | | | | | | | | On a 8308 based board it was found that the PEX_GLK_RATIO register (programmed in arch/powerpc/cpu/mpc83xx/pcie.c) was getting set to 0, This was tracked to the fact that the pci express clock frequency was not being assigned to the pciexp1_clk entry in the global data structure in file arch/powerpc/cpu/mpc83xx/speed.c. Fix this and a similiar issue in 'do_clocks' command. Signed-off-by: Bill Cook <cook@isgchips.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* MPC83xx: add config options for memory setup.Andre Schwarz2011-07-06-1/+18
| | | | | | | | | CPO value and driver strength settings are board specifc. Also allow SPD data fetch from any accessible I2C EEPROM. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* MPC837x: set i2c1_clkAndre Schwarz2011-07-06-0/+2
| | | | | | | | | Running on mpc837x without CONFIG_FSL_ESDHC leads to i2c1_clk not being set at all. It is bound to clock of encryption module. fix this. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Minor coding style cleanup.Wolfgang Denk2011-05-19-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* powerpc/mpc8xxx: reword max tCKmin messageYork Sun2011-05-13-3/+3
| | | | | | | | Reword "The DIMM max tCKmin is ..." to "The DDR clock is faster than the slowest DIMM(s) can support". Fixed interger type in printf as well. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: fix compatible property for the L2 cache nodeTimur Tabi2011-05-13-10/+19
| | | | | | | | | The compatible property for the L2 cache node (on 85xx systems that don't have a CPC) was using a value for the property length that did not match the actual length of the property. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* PPC405EX CHIP_21 erratumSteven A. Falco2011-05-12-0/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated 4/27/11) states that rev D processors may wake up with the wrong feature set. This patch implements the APM-proposed workaround. To enable this patch for your board, add the appropriate define for your CPU to your board header file. See kilauea.h for more information. The following variants are supported: #define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY #define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY #define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY #define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY Please note that if you select the wrong define, your board will not boot, and JTAG will be required to recover. Tested on custom boards using: CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY <sfalco@harris.com> CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY <eibach@gdsys.de> Signed-off-by: Steve Falco <sfalco@harris.com> Acked-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2011-05-10-3/+1
|\
| * mpc83xx: restrict UTMI PHY configuration to 831x partsKim Phillips2011-04-04-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | i.e, to those parts that have PHY_CLK_VALID bits in their USB CONTROL registers: mpc8308 WU_INT, PHY_CLK_SEL, USB_EN, WU_INT_EN, ULPI_INT_EN mpc831x PHY_CLK_VALID, WU_INT, CLKIN_SEL, PHY_CLK_SEL, UTMI_PHY_EN, PLL_RESET, REFSEL, OTG_PORT, KEEP_OTG_ON, LSF_EN, USB_EN, ULPI_INT_EN mpc834x USB_EN, ULPI_INT1_EN (MPH only), ULPI_INT0_EN mpc837x USB_EN, ULPI_INT_EN (mpc832x, mpc8360 don't have a USB_EHCI_FSL compatible controller) this prevents non-831x parts from never completing cpu_init_f(), because the (non-existent) PHY_CLK_VALID bit never gets set. Reported-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Tested-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2011-04-30-55/+376
|\ \
| * | fsl-ddr: Fix mixed-case macro namesKyle Moffett2011-04-29-9/+9
| | | | | | | | | | | | | | | Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Change timebase divisor to be defined per processorKumar Gala2011-04-28-5/+6
| | | | | | | | | | | | | | | | | | | | | | | | Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because different SoCs have different divisor amounts. All the PQ3 parts are /8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Implement work-around for P4080 erratum SERDES-A001Timur Tabi2011-04-28-16/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1 are swapped. Erratum SERDES-A001 says that if bank two is kept disabled and after bank three is enabled, then the PLL for bank three won't lock properly. The work-around is to enable and then disable bank two after bank three is enabled. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Extend SERDES9 erratum work-around to SGMII, SRIO, and AURORATimur Tabi2011-04-28-17/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | Part of the SERDES9 erratum work-around is to set some bits in the SerDes TTLCR0 register for lanes configured as XAUI, SGMII, SRIO, or AURORA. The current code does this only for XAUI, so extend it to the other protocols. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Display SERDES 8 erratum warning if banks are not disabledTimur Tabi2011-04-28-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | The work-around for P4080 erratum SERDES-8 requires all lanes of banks two and three to be disabled (powered down) in the RCW. Display a warning message if this is not the case. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Implement work-around for P4080 erratum SERDES-A005Timur Tabi2011-04-28-0/+51
| | | | | | | | | | | | | | | | | | | | | | | | SerDes PLL bandwidth default setting is incorrect when no lanes are configured as PCI Express. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Enable Internal USB PHY for p2040, p3041, p5010 and p5020Roy Zang2011-04-27-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we need to enable for them to function. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | p4080/serdes: Implement the XAUI workaround for SERDES9 erratumEmil Medve2011-04-27-0/+110
| | | | | | | | | | | | | | | | | | Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: fsl_corenet_serdes code reworkEmil Medve2011-04-27-3/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rework and add some new APIs to the fsl_corenet_serdes code for use by erratum and drivers. * Rename serdes_get_bank() to serdes_get_bank_by_lane() * Add serdes_get_first_lane returns which SERDES lane is used by device Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Add device tree fixup for bman portalHaiying Wang2011-04-27-0/+31
| | | | | | | | | | | | | | | | | | | | | Fix fdt bportal to pass the bman revision number to kernel via device tree. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Change CS timing params before changing CS properties on IFCDipen Dudhat2011-04-27-16/+15
| | | | | | | | | | | | | | | | | | | | | | | | To make sure that machine change operation work successfully, change timing parameters first before changing machine for chip select on IFC. Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | mpc832x: add support for the mpc8321 based suvd3 boardHeiko Schocher2011-04-30-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - serial console on UART1 - Ethernet RMII over UCC4 - PHY SMSC LAN8700 - 64MB Flash - 128 MB DDR2 RAM - I2C - bootcount This board is similiar to the kmeter1 (8360) board, so common config options are extracted into the include/configs/km83xx-common.h file. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* | | powerpc: use 'video-mode' environment variable to configure DIUTimur Tabi2011-04-28-13/+3
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the 'video-mode' environment variable (for Freescale chips that have a DIU display controller) to designate the full video configuration. Previously, the DIU driver used the 'monitor' variable, and it was used only to determine the output video port. The old definition of the "monitor" environment variable only determines which video port to use for output. This variable was set to a number (0, 1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The resolution was hard-coded into board-specific code. The Linux command-line arguments needed to be hard-coded to the proper video definition string. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
* | Merge branch 'phylib' of git://git.denx.de/u-boot-mmcWolfgang Denk2011-04-20-20/+3
|\ \
| * | fsl: Change fsl_phy_enet_if to phy_interface_tAndy Fleming2011-04-20-20/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum. This meant that drivers which used fsl_phy_enet_if to deal with PHY interfaces would have to convert between the two (or we would have to have them mirror each other, and deal with the ensuing maintenance headache). Instead, we switch all clients of fsl_phy_enet_if over to phy_interface_t, which should become the standard, anyway. Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Detlev Zundel <dzu@denx.de>
* | | Revert "PowerPC: Add support for -msingle-pic-base"Wolfgang Denk2011-04-20-125/+12
|/ / | | | | | | | | | | | | This reverts commit 39768f7715ed637ef02f49fc7de664cc1aaf14b3. Reson: it breaks a number of boards with embedded environment as the code size grows in some places.
* | PowerPC: Add support for -msingle-pic-baseJoakim Tjernlund2011-04-11-12/+125
| | | | | | | | | | | | | | | | | | | | | | | | | | -msingle-pic-base is a new gcc option for ppc and it reduces the size of my u-boot with 6-8 KB. While at it, add -fno-jump-tables too to save a few more bytes. -msingle-pic-base will be in gcc 4.6, however backported patches are available at http://bugs.gentoo.org/show_bug.cgi?id=347281 Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* | PowerPC: Move -fPIC flag to common placeJoakim Tjernlund2011-04-11-12/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The -fPIC flag belongs with -mrelocatable, move it there. Also change -fPIC to -fpic as this produces smaller binaries. However, currently -mrelocatable promotes -fpic to -fPIC, a fix for this is in upcoming gcc 4.6 or you can apply this small patch to gcc: diff --git a/gcc/config/rs6000/sysv4.h b/gcc/config/rs6000/sysv4.h index 8da8410..e4b8280 100644 --- a/gcc/config/rs6000/sysv4.h +++ b/gcc/config/rs6000/sysv4.h @@ -227,7 +227,8 @@ do { \ } \ \ else if (TARGET_RELOCATABLE) \ - flag_pic = 2; \ + if (!flag_pic) \ + flag_pic = 2; \ } while (0) #ifndef RS6000_BI_ARCH -- Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* | powerpc/85xx: Removed clearing of L2-as-SRAMFabian Cenedese2011-04-10-7/+0
| | | | | | | | | | | | | | | | Removed clearing of L2 cache as SRAM as it is not necessary without ECC. This also speeds up the booting process. Signed-off-by: Fabian Cenedese <cenedese@indel.ch> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: Add PBL boot from SPI flash support on P4080DSShaohui Xie2011-04-10-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as 1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from CPC after PBL completes RCW and PBI phases. Signed-off-by: Chunhe Lan <b25806@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | p4080ds: remove rev1-specific code for the SERDES8 erratumTimur Tabi2011-04-10-59/+47
| | | | | | | | | | | | | | | | Remove the SERDES8 erratum work-around code that only applied to P4080 rev1, which is not supported by this version of U-Boot. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: rename NAND prefixes to CONFIG_SYSMatthew McClintock2011-04-08-4/+4
| | | | | | | | | | | | | | | | | | | | renaming 85xx define CONFIG_NAND_OR_PRELIM to CONFIG_SYS_NAND_OR_PRELIM and CONFIG_NAND_BR_PRELIM to CONFIG_SYS_NAND_BR_PRELIM to use the more appropriate CONFIG_SYS prefix as well as be consistent with 83xx. Signed-off-by: Matthew McClintock <msm@freescale.com> cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: Add P1021 specific QE and UEC supportHaiying Wang2011-04-05-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | P1021 has some QE pins which need to be set in pmuxcr register before using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to be released after MII access because QE12 pin is muxed with LBCTL signal. Also added relevant QE support defines unique to P1021. The P1021 QE is shared on P1012, P1016, and P1025. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-12-26 11:02:18 +0000