summaryrefslogtreecommitdiff
path: root/arch/arm
Commit message (Collapse)AuthorAgeLines
* ENGR00328312 i2c: imx: Optimize the i2c device recovery solutionFugang Duan2017-04-05-2/+26
| | | | | | | | | | | | | | | | | | | From i2c spec, if device pull down the SDA line that causes i2c bus dead, host can send out 9 clock to let device release SDA. But for some special device like pfuze100, it pull down SDA line and the solution cannot take effort. The patch just add NACK and STOP signal after 8 dummy clock, and pmic can release SDA line after the recovery. Test case catch 375 times of i2c hang, and all are recovered. Signed-off-by: Fugang Duan <B38611@freescale.com> (cherry picked from commit 53118db42d201d36ca9067b4bb0e2702399e100b) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit b8dcb812401026cb2189b24a4f6058830151c85a) (cherry picked from commit c5a44a2a0b2218221cb12645b10f0b34ecc6f79b)
* MLK-10576 ARM: i.MX6: exclude the ARM errata from i.MX6 UP systemNitin Garg2017-04-05-5/+0
| | | | | | | | | | | | | | | | | The ARM errata 751472, 794072, 761320, 845369 only applied to the following configuration: This erratum affects configurations with either: - One processor if the ACP is present - Two or more processors i.MX6 family does not have the ACP and thus only the MPCore system will be impacted, which are the i.MX6DQ, i.MX6DL, and i.MX6QP. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> (cherry picked from commit 0db960784ba4f631ee5c0321b5d25f3b1ac55640) (cherry picked from commit 850f27d137a083a141c99fe9828d596807937d38)
* MLK-10524: iMX6x: Implement workaround for Cortex-A9 errata 845369Nitin Garg2017-04-05-0/+10
| | | | | | | | | | | Under very rare timing circumstances, transitioning into streaming mode might create a data corruption. Present on Two or more processors or 1 core with ACP, all revisions. This erratum can be worked round by setting bit[22] of the undocumented Diagnostic Control Register to 1. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> (cherry picked from commit 70ad44e523680de67dd8b7a7505d7f27799980ee) (cherry picked from commit f20a65847577ff40dc7e3739a0bb69926885c734)
* MLK-12557 mx6ul: Enable syscounter as default timerYe Li2017-04-05-3/+14
| | | | | | | | | Use syscounter for i.MX6UL platform as default timer, not use GPT. Add a CONFIG_GPT_TIMER for selecting GPT. Using CONFIG_SYSCOUNTER_TIMER for selecting system counter. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 1c27c9ecf80b3cc63a7c9751ebfd11755f847b1d)
* ENGR00325255 pcie:enable pcie support on imx6sx sdYe Li2017-04-05-5/+35
| | | | | | | | | | | | | | | | | Enable pcie support in uboot on imx6sx sd boards - enable_pcie_clock should be call before ssp_en is set, since that ssp_en control the phy_ref clk gate, turn on it after the source of the pcie clks are stable. - add debug info - add rx_eq of gpr12 on imx6sx - there are random link down issue on imx6sx. It's pcie ep reset issue. solution:reset ep, then retry link can fix it. (cherry picked from commit ec78595a24b5ff1020baa97b6d6e79a3a3326307) Signed-off-by: Richard Zhu <r65037@freescale.com> Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 81fd30250110d72992758f08b66c07306126892b)
* ENGR00319965 pcie: mask the imx6sl outRichard Zhu2017-04-05-15/+20
| | | | | | | | | | imx6sl doesn't have the pcie module, mask the pcie related codes from imx6sl. Signed-off-by: Richard Zhu <r65037@freescale.com> (cherry picked from commit acaff11da33f8f0cb1521d3c48e64e7ed9a87bec) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit 48a4606ef575c72e16e31c167dce042fcb66191c)
* ENGR00319415 pcie: random link down issue after warm-rstRichard Zhu2017-04-05-0/+18
| | | | | | | | | | | | | | | | | | | | | There are about 0.02% percentage on some imx6q/dl/solo hw boards, random pcie link down when warm-reset is used. Make sure to clear the ref_ssp_en bit16 of gpr1 before warm-rst, and set ref_ssp_en after the pcie clks are stable to workaround it. rootcause: * gpr regisers wouldn't be reset by warm-rst, while the ref_ssp_en is required to be reset by pcie. (work-around in u-boot) * ref_ssp_en should be set after pcie clks are stable. (work-around in kernel) Signed-off-by: Richard Zhu <r65037@freescale.com> (cherry picked from commit 5cc825b12c6b86a22f1a6a0535b52cf3ee142e77) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit 6193cf4e3384a59e29546d13a67657f7faeafc9e) (cherry picked from commit 7b4aabeddffabca46d7d6e7ef2611de468a6b4f7)
* MLK-11064 imx: mx6qp: Adjust AQos settings for peripheralsYe.Li2017-04-05-0/+3
| | | | | | | | | | | To resolve USB camera bandwidth issue, the patch sets recommended AQoS setting from IC team value for peripheral and only on imx6qp. The address is: 0xbb0608, the value is: 0x80000201 Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 11906c712a52e7a20caf71d7c5da4e951a59db29) (cherry picked from commit 5dcf073b8f2479a2adbb8d9fb03d9c9c70664e32)
* MLK-12534 mx6: shutdown vddpu and PCIE phy to save powerYe Li2017-04-05-0/+42
| | | | | | | | | | | | | | | | | | | Shutdown VDDPU and PCIE phy to save power. For PCIE, the i.MX6SL and i.MX6UL does not have this module, so don't need it. For VDDPU, the i.MX6UL does not have GPU, does not need it. And on i.MX6QP there is narrow window that PRE driver is ready but GPU driver probe later, and the later GPU driver turn on PU may cause 'PRE hang' issue. To simplify thing, do not turn off PU in u-boot. Reference: commit: 6b0787b726e2ff32210d742d93ecd3f4bb2ae402 commit: 4bd0032c0eba50fa0caf43f50f735a3cfbe36a8d Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 5c96ea91fe89c67991c929c9b39ffaa940d28391)
* MLK-12533 mx6sx: select OSC as uart's clk parentYe Li2017-04-05-0/+13
| | | | | | | | | | | As M4 is sourcing UART clk from OSC, to make UART work when M4 is enabled, need to select OSC as clk parent, 24M OSC is enough for debug UART in uboot. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Anson Huang <b20788@freescale.com> (cherry picked from commit b5e1b393192099e91c5cb75b69291c87eacb9f60) (cherry picked from commit 416dea861c2dd5a197bf2354069bba8415a20b12)
* ENGR00315894-81 gis: Add gis moduleYe.Li2017-04-05-1/+9
| | | | | | | | | | | Add gis module, current gis is support vadc input. Add power down function to lcdif driver. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit a007b00dd8ef9f773dfdebef0b1deb0990281793) (cherry picked from commit a31dcdafb0963381e7213c59f79a340ef27ec2e2) (cherry picked from commit 02dfe2e4af5f51d39a51542fb0e81f93faf505bc)
* ENGR00321299 gis: clean csi0 input mux set bit in GPRSandor Yu2017-04-05-0/+6
| | | | | | | | | | | | When gis enable in uboot, the CSI0 input mux select setting to vadc module, clean the bit when gis disabled. Signed-off-by: Sandor Yu <R01008@freescale.com> (cherry picked from commit ae66b17b7da3be50dc81ca636b67e8e879f52e26) (cherry picked from commit c83fd326e810c2fff44b8b02e78406d5d04c977c) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit d6e803ed5f51d31ebe7e9d178aa11f16401b7fc8) (cherry picked from commit 2065b417ae93436736e49ca66b66aa0791d003fe)
* ENGR00315894-77 mx6 soc: Add vadc power up/down functionYe.Li2017-04-05-0/+49
| | | | | | | | | | | Add vadc power up/down function. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 96d990ef754a879f6ca9da4adf6e0be3d21cdc51) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit 01b88201aa86bef26a4254ac43aff90e99fd2c06) (cherry picked from commit d50b53f138dd3b4c463c80ac8e14f41ac0fdd415)
* ENGR00315894-76 mx6 clock: Add vadc clock enable functionYe.Li2017-04-05-0/+13
| | | | | | | | | | | Add vadc clock enable function. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 721c7a1448c5b7265b597b83d18f8338a27ea213) Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit 903a59ef941f39b6d7f693dd7c60528e166de079) (cherry picked from commit dc767fb7d5c155f2a6ef01c4dee808b9c1944fc2)
* MLK-12437-3 mx6sxsabresd: Update display to support panel selectionYe Li2017-04-05-0/+2
| | | | | | | | Support two display panels, one for LVDS, another for parallel LCD. Align the feature to the v2015.04 uboot. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit d7f54f22607ffcace6cda97984649a5ae4f65996)
* MLK-12437-2 Video: Update the common board_video_skip to support MXS LCDYe Li2017-04-05-0/+14
| | | | | | | Update the board_video_skip to use CONFIG_VIDEO_MXS for LCD display support. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit d6d0265b09e66c576ab4c01841166415f834a1ff)
* MLK-12437-1 mx6sx: Add support for LVDS displayYe Li2017-04-05-1/+63
| | | | | | | | The i.MX6SX uses a LVDS bridge to mux to the LCDIF interface. Implmement a function for this muxing. So that on 6SX we can use a LVDS display. Signed-off-by: Ye Li <ye.li@nxp.com> (cherry picked from commit 763658d9b497e44b7411581da592ef5b522e9cc9)
* ENGR00315894-70 iMX6SX:Video Update MXS LCDIF driverYe.Li2017-04-05-1/+1
| | | | | | | | | | | | | | | Add a new interface "mxs_lcd_panel_setup" to setup fb parameters and specifies the LCDIF controller for multiple controllers of iMX6SX. Pass fb parameters via "videomode" env remains work if the new interface is not called before video initialization. Modify LCDIF clock interface "mxs_set_lcdclk" to support multiple LCDIF controllers on iMX6SX. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit d7f49b9378547c3a57b96bcdb907fc44616beb3d) (cherry picked from commit e1343191b9de227c582847e7eeb5ce9238be0754)
* MLK-12434-9: mx6: define CONFIG_BOARD_LATE_INITPeng Fan2017-04-05-0/+5
| | | | | | | | Define CONFIG_BOARD_LATE_INIT for mx6qarm2/mx6slevk/mx6sxsabresd to let mmcdev/mmcroot work as expected. Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit 86135fb7e55c3046ead899b83f58dd6048eda9e8)
* MLK-12434-1: imx: dynamic setting mmcdev and mmcrootPeng Fan2017-04-05-0/+5
| | | | | | | | Align to imx_v2015.04, dynamic setting mmcdev and mmcroot. Then when boot linux, we can have correct "root=/dev/mmcblk[x]p2" Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit b46b99a901eb194e81fc4836ee2259ad8857f4d3)
* MLK-12425-1: mx6sl/ul: introudce more pinmux macrosPeng Fan2017-04-05-3/+84
| | | | | | | Introuduce more pinmux macros definitions. Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit 06893558f2cc042b683247989be5127a8027ebf2)
* MLK-12693-2 nand: mxs: correct bitflip for erased NAND pagePeng Fan2017-04-05-1/+5
| | | | | | | | | | | | | | | | | | | | This patch is a porting of http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/?h=imx_4.1.15_1.0.0_ga&id=e4dacc44d22e9474ec456cb330df525cd805ea38 " i.MX6QP and i.MX7D BCH module integrated a new feature to detect the bitflip number for erased NAND page. So for these two platform, set the erase threshold to gf/2 and if bitflip detected, GPMI driver will correct the data to all 0xFF. Also updated the imx6qp dts file to ditinguish the GPMI module for i.MX6Q with the one for i.MX6QP. " In this patch, i.MX6UL is added and threshold changed to use ecc_strength. Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit 489929be0221bb7d4c46bb5bc6083650b78f73e0) Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-11528 imx: mx6ul check fuse before init beePeng Fan2017-03-14-1/+11
| | | | | | | | | | | | Need to check fuse bit 25 of bank 0 word 4 before initialize bee. The bit: 0 means bee enabled, 1 means bee disabled. If disabled, continuing initialize bee will cause system hang, so need to check this bit before initialize bee. Add macro to enable BEE in header file, default disabled. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit ef4cb7c53418e4e1dd7cfcb7c6974cfea77ef3c0)
* MLK-10958 imx: mx6ul support Bus Encryption EnginePeng Fan2017-03-14-1/+513
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is to support Bus Encryption Engine(BEE) for i.MX 6UL. Supported feature: 1. SNVS key and soft key 2. CTR and ECB mode 3. Specify address region to bee. Two commands are included: bee init [key] [mode] [start] [end] - BEE block initial "Example: bee init 1 1 0x80000000 0x80010000\n" bee test [region] "Example: bee test 1\n" Mapping: [0x10000000 - (0x10000000 + size - 1)] : [start - (start + size - 1)] [0x30000000 - (0x30000000 + IRAM_SIZE - 1)] : [IRAM_BASE_ADDR - (IRAM_BASE_ADDR + IRAM_SIZE - 1)] Whatever start is, start - (start + size -1) will be fixed mapping to 0x10000000 - (0x10000000 + size - 1) Since default AES region's protected size is SZ_512M, so on mx6ul evk board, you can not simply run 'bee init', it will overlap with uboot execution environment, you can use 'bee init 0 0 0x80000000 0x81000000'. If want to use bee, Need to define CONFIG_CMD_BEE in board configuration header file, since CONFIG_CMD_BEE default is not enabled. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> (cherry picked from commit 29b9bdbbdac9678dba9b7bc2d3662598e9c548a5) (cherry picked from commit 6d45292ff7e7020a48842f033f8a337daabe4476)
* MLK-12416-4: imx: mx6: update imx-regs.hPeng Fan2017-03-14-13/+119
| | | | | | | Update imx-regs.h to align with 2016.03 Signed-off-by: Peng Fan <peng.fan@nxp.com> (cherry picked from commit 9bbd54e44ae1f0868d3f0dd34975e76606b0a5e8)
* MLK-14422 imx7d: wdog: Overwrite the reset_cpu to turn off internal reset signalYe Li2017-03-14-0/+15
| | | | | | | | Set wdog WCR register SRS bit to turn off internal reset signal WDOG_RESET_B_DEB for mx7d. So that the warm reset is disabled. The WDA is cleared to output WDOG_B immediately to reset the board. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14420-2 DTS: add DTS file for imx6q sabresd boardYe Li2017-03-14-0/+1123
| | | | | | Copy the dts and dtsi files from kernel to support imx6q sabresd board. Signed-off-by: Ye Li <ye.li@nxp.com>
* MLK-14420-1 DTS: Update imx6qdl relevant dts and clock definitionsYe Li2017-03-14-418/+451
| | | | | | Get the latest dtsi files and clock.h for imx6qdl from kernel Signed-off-by: Ye Li <ye.li@nxp.com>
* arm: omap-common: Fix typo in CONFIG_OMAP54XX guardMatthijs van Duin2017-03-11-1/+1
| | | | | | | | Some initialization was unintentionally being skipped on omap5. Fixes: f5af0827f276 ("arm: omap-common: Guard some parts of the code with CONFIG_OMAP44XX/OMAP54XX") Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* arm: OMAP2+: nandecc: propagate error to command return statusLadislav Michl2017-03-11-20/+16
| | | | | | | | | Currently nandecc returns zero even if underlaying omap_nand_switch_ecc function fails. Fix that by propagating error returned to command return value. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: Migrate errata to KconfigTom Rini2017-03-09-6/+85
| | | | | | | | | This moves all of the current ARM errata from various header files and in to Kconfig. This allows for a minor amount of cleanup as we had some instances where both a general common header file was enabling errata as well as the board config. We now just select these once at the higher level in Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* omap4: Migrate to using implyTom Rini2017-03-09-36/+12
| | | | | | | Move the default y options under arch/arm/mach-omap2/omap4/Kconfig to be using imply instead in arch/arm/Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* omap3: Migrate to using implyTom Rini2017-03-09-33/+11
| | | | | | | Move the default y options under arch/arm/mach-omap2/omap3/Kconfig to be using imply instead in arch/arm/Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* TI: Migrate board/ti/common/Kconfig to implyTom Rini2017-03-09-46/+39
| | | | | | | The option that we had set in board/ti/common/Kconfig as default y are best done with imply under the appropriate main Kconfig option instead. Signed-off-by: Tom Rini <trini@konsulko.com>
* am335x_evm: Switch to using imply keywordTom Rini2017-03-09-0/+3
| | | | | | | | These particular SPL options are part of what the ROM provides, but for compatibility with how we have previously used them, move them to being implied by the board being selected. Signed-off-by: Tom Rini <trini@konsulko.com>
* do_smhload: fix return codeRyan Harkin2017-03-09-2/+2
| | | | | | | | | | | | | do_smhload was using a ulong to store the return value from smh_load_file. That returns an int, where -1 indicates an error. As a ulong will never be negative, smh_load_file errors were not detected and so_smhload always returned zero. Also, when errors were spotted, do_smhload was returning 1, rather than the enumeration CMD_RET_FAILURE (which is also 1). Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
* Freescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigsTom Rini2017-03-09-5/+1
| | | | | | | | | | | | | | | | | | | | | | In some cases this is absolutely required, so select this for some secure features. This also requires migration of RSA_FREESCALE_EXP Cc: Ruchika Gupta <ruchika.gupta@nxp.com> Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: Priyanka Jain <Priyanka.Jain@freescale.com> Cc: Sumit Garg <sumit.garg@nxp.com> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Cc: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Feng Li <feng.li_2@nxp.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Mingkai Hu <Mingkai.Hu@freescale.com> Cc: York Sun <york.sun@nxp.com> Cc: Saksham Jain <saksham.jain@nxp.freescale.com> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* armv8: spl: Call spl_relocate_stack_gd for ARMv8Philipp Tomsich2017-03-01-2/+12
| | | | | | | | | | As part of the startup process for boards using the SPL, we need to call spl_relocate_stack_gd. This is needed to set up malloc with its DRAM buffer. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* armv5te: make 'ret lr' produce iinterworking 'bx lr'Albert ARIBAUD2017-03-01-1/+1
| | | | | | | | | | | | | | | | | Current ARM assembler helper for the 'return to caller' pseudo-instruction turns 'ret lr' into 'mov pc, lr' for ARMv5TE. This causes the core to remain in its current ARM state even when the routine doing the 'ret' was called from Thumb-1 state, triggering an undefined instruction exception. This causes early run-time failures in all boards compiled using the Thumb-1 instruction set (for instance the Open-RD family). ARMv5TE supports 'bx lr' which properly implements interworking and thus correctly returns to Thumb-1 state from ARM state. This change makes 'ret lr' turn into 'bx lr' for ARMv5TE. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* arm: mach-omap2: Flush cache after FIT post-processing imageAndrew F. Davis2017-02-27-0/+6
| | | | | | | | | | After we authenticate/decrypt an image we need to flush the caches as they may still contain bits of the encrypted image. This will cause failures if we attempt to jump to this image. Reported-by: Yogesh Siraswar<yogeshs@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: set up charge pump current for MPLL of LD11 SoCMasahiro Yamada2017-02-23-0/+24
| | | | Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: add simple eMMC load APIs instead of ROM APIMasahiro Yamada2017-02-23-58/+195
| | | | | | | | | | | Re-use of routines embedded in the Boot ROM requires a function pointer table for each SoC. This is not nice in terms of the maintainability in a long run. Implement simple eMMC load APIs that are commonly used for LD11, LD20, and hopefully future SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: deassert RST_n of eMMC device for LD11/LD20Masahiro Yamada2017-02-23-1/+25
| | | | | | | | | | | | | For LD11 and LD20 SoCs, the RST_n pin is asserted by default. If the EXT_CSD[162], bit[1:0] (RST_n_ENABLE) is fused, the eMMC device would stay in the reset state until its RST_n pin is deasserted by software. Currently, this is cared by an ad-hoc way because the eMMC hardware reset provider is not supported in U-Boot for now. This code should be re-written once the "mmc-pwrseq-emmc" binding is supported. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: add DRAM PHY clock duty adjustment for LD20 SoCKotaro Hayashi2017-02-23-2/+8
| | | | | | | | | | If the DRAM clock duty does not meet the allowable tolerance, it is marked in an efuse register. If the register is fused, the boot code should compensate for the DRAM clock duty error. Signed-off-by: Kotaro Hayashi <hayashi.kotaro@socionext.com> [masahiro: simplify code, add git-log] Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: remove dram_nr_ch from board parametersMasahiro Yamada2017-02-23-26/+18
| | | | | | | This parameter is redundant because we can know the number of channels by checking if dram_ch[2].size is zero. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: rework spl_boot_device() and related codeMasahiro Yamada2017-02-23-344/+312
| | | | | | | | The current implementation has ugly switch statements here and there, and duplicates similar code. Rework it using table lookups for SoC data and reduce code duplication. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: move spl_boot_mode() to a separate fileMasahiro Yamada2017-02-23-24/+35
| | | | | | | | The spl_boot_mode() is unrelated to the other code in this file. Besides, this function is only called from common/spl/spl_mmc.c, so it is reasonable to guard with CONFIG_SPL_MMC_SUPPORT. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: move MMC code to a separate fileMasahiro Yamada2017-02-23-38/+47
| | | | | | | | | | Currently, arch/arm/mach-uniphier/boot-mode/boot-mode.c is messed up with unrelated code; there is no reason why the "mmcsetn" command must be placed in this file. Split out the MMC code into arch/arm/mach-uniphier/mmc-first-dev.c. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: dts: uniphier: drop u-boot, dm-pre-reloc from system-bus pinctrl nodeMasahiro Yamada2017-02-23-8/+0
| | | | | | | | Since commit 26b09c022ab6 ("ARM: uniphier: move SBC and Support Card init code to U-Boot proper"), SPL does not need pin-mux settings for the System Bus. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: remove DRAM base address from board parametersMasahiro Yamada2017-02-23-57/+36
| | | | | | | | | The base address of each DRAM channel can be calculated from other parameters, so does not need hard-coding. What we need is the size of each DRAM channel and DRAM_SPARSE flag to decide the start address of DRAM channel 1. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit v1.1 at 2024-11-09 15:25:25 +0000