summaryrefslogtreecommitdiff
path: root/arch/arm
Commit message (Collapse)AuthorAgeLines
* armv7: ls1021a: Convert CONFIG_LS1_DEEP_SLEEP to Kconfig optionYork Sun2016-09-26-0/+5
| | | | | | | | Move this option to Kconfig and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> CC: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_FSL_ERRATUM_A010315 to Kconfig optionYork Sun2016-09-26-2/+17
| | | | | | | Move this option to Kconfig and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
* armv8: ls1012a: Convert CONFIG_LS1012A to Kconfig option ARCH_LS1021AYork Sun2016-09-26-8/+16
| | | | | | | | | Move this config to Kconfig option and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> CC: Calvin Johnson <calvin.johnson@nxp.com> CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* armv8: ls1046a: Convert CONFIG_LS1046A to Kconfig option ARCH_LS1046AYork Sun2016-09-26-4/+11
| | | | | | | | | Move this option to Kconfig and clean up existing uses. Signed-off-by: York Sun <york.sun@nxp.com> CC: Mingkai Hu <mingkai.hu@nxp.com> CC: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* armv8: ls1046aqds: Add LS1046AQDS board supportShaohui Xie2016-09-14-0/+107
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls1046ardb: Add LS1046ARDB board supportMingkai Hu2016-09-14-0/+224
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS1046ARDB Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 512 Mbyte NAND flash * Two 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card * On-board 4G eMMC Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: * PCIe1 (SerDes2 Lane0) to miniPCIe slot * PCIe2 (SerDes2 Lane1) to x2 PCIe slot * PCIe3 (SerDes2 Lane2) to x4 PCIe slot SATA: * SerDes2 Lane3 to SATA port USB 3.0: one super speed USB 3.0 type A port one Micro-AB port UART: supports two UARTs up to 115200 bps for console Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls1046a: disable SATA ECC in DCSRShaohui Xie2016-09-14-0/+4
| | | | | | | | | This is a workaround to fix SATA CRC error. Once the root cause is found the ECC disabling will be removed. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls1046a: Enable DDR erratum for ls1046aShengzhou Liu2016-09-14-0/+6
| | | | | | | | | Enable ERRATUM_A008511, ERRATUM_A009801, ERRATUM_A009803, ERRATUM_A009942, ERRATUM_A010165 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: fsl-layerscape: spl: remove BSS clearing and board_init_rQianyu Gong2016-09-14-5/+0
| | | | | | | | | | As per the top level U-Boot README "Board Initialisation Flow" section, board_init_f() should return without calling board_init_r() directly. Clearing BSS and calling board_init_r() will be done in crt0_64.S. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: fsl-layerscape: add define CONFIG_STANDALONE_LOAD_ADDR for standalone appShaohui Xie2016-09-14-0/+2
| | | | | | | | The CONFIG_STANDALONE_LOAD_ADDR is set to 0x80300000 by default. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: fsl-layerscape: Increase L2 Data RAM latency and L2 Tag RAM latencyMingkai Hu2016-09-14-0/+15
| | | | | | | | | | | According to design specification, the L2 cache operates at the same frequency as the A72 CPUs in the cluster with a 3-cycle latency, so increase the L2 Data RAM and Tag RAM latency to 3 cycles, or else, will run into different call trace issues. Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* driver/ddr/fsl: Add general MMDC driver and reuse common MMDC driver for ls1012aShengzhou Liu2016-09-14-1/+3
| | | | | | | | | | | | | | This general MMDC driver adds basic support for Freescale MMDC (Multi Mode DDR Controller). Currently MMDC is integrated on ARMv8 LS1012A SoC for DDR3L, there will be a update to this driver to support more flexible configuration if new features (DDR4, multiple controllers/chip selections, etc) are implimented in future. Meantime, reuse common MMDC driver for LS1012ARDB/LS1012AQDS/ LS1012AFRDM. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv7:ls1021a: Enable workaround for DDR erratum A-009942Shengzhou Liu2016-09-14-0/+1
| | | | | Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* nxp: ls102xa: add LS1 PSCI system suspendHongbo Zhang2016-09-14-1/+248
| | | | | | | | The deep sleep function of LS1 platform, is mapped into PSCI system suspend function, this patch adds implementation of it. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* nxp: ls102xa: add EPU Finite State MachineHongbo Zhang2016-09-14-0/+165
| | | | | | | | The EPU Finite State Machie (FSM) is used in both the last stage of system suspend and the earliest stage of system resume. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* nxp: ls102xa: add registers definition for system sleepHongbo Zhang2016-09-14-1/+53
| | | | | | | | This patch adds definitions of all the regesters necessary for system sleep. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv7: psci: make v7_flush_dcache_all public for all psci codeHongbo Zhang2016-09-14-3/+5
| | | | | | | | | | | The v7_flush_dcache_all function will be called by ls102xa platform system suspend, it is necessary to make it a public call instead of a local one, but changing the LENTRY to ENTRY isn't enough, because there is another one using the same name, so this one gets a psci_ prefix. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls2080a: Remove debug server supportYork Sun2016-09-14-14/+0
| | | | | | Debug server feature has been dropped from roadmap. Signed-off-by: York Sun <york.sun@nxp.com>
* fsl-layerscape: Add workaround for PCIe erratum A010315Hou Zhiqiang2016-09-14-0/+41
| | | | | | | | | | As the access to serders protocol unselected PCIe controller will hang. So disable the R/W permission to unselected PCIe controller including its CCSR, IO space and memory space according to the serders protocol field of RCW. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* fsl: csu: add an API to set R/W permission to PCIeHou Zhiqiang2016-09-14-0/+1
| | | | | Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* arm: fsl-layerscape: move forward the non-secure access permission setupHou Zhiqiang2016-09-14-4/+10
| | | | | | | | | | Move forward the basic non-secure access enable operation, so the subsequent individual device access permission can override it. And collect the dispersed callers in board level, and then move them to SoC level. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* fsl: serdes: ensure accessing the initialized maps of serdes protocolHou Zhiqiang2016-09-14-2/+49
| | | | | | | | | | | | Up to now, the function is_serdes_configed() doesn't check if the map of serdes protocol is initialized before accessing it. The function is_serdes_configed() will get wrong result when it was called before the serdes protocol maps initialized. As the first element of the map isn't used for any device, so use it as the flag to indicate if the map has been initialized. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* ls1043ardb: PPA: add PPA validation in case of secure bootSumit Garg2016-09-14-0/+39
| | | | | | | | | | As part of Secure Boot Chain of trust, PPA image must be validated before the image is started. The code for the same has been added. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: fsl-layerscape: Update ddr erratum a008336Shengzhou Liu2016-09-14-2/+4
| | | | | | | | | DDR erratum A008336 only applies to DDR controller v5.2.0. DDR controller v5.2.1 already has default 0x43b30002 in EDDRTQCR1 register for optimal performance. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-09-09-4/+9
|\
| * mx6: ddr: Allow changing REFSEL and REFR fieldsFabio Estevam2016-09-06-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently MX6 SPL DDR initialization hardcodes the REF_SEL and REFR fields of the MDREF register as 1 and 7, respectively for DDR3 and 0 and 3 for LPDDR2. Looking at the MDREF initialization done via DCD we see that boards do need to initialize these fields differently: $ git grep 0x021b0020 board/ board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */ board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800 board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800 board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800 So introduce a mechanism for users to be able to configure REFSEL and REFR fields as needed. Keep all the mx6 SPL users in their current REF_SEL and REFR values, so no functional changes for the existing users. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
| * arm: imx: Add support for Advantech DMS-BA16 boardAkshay Bhat2016-09-06-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Advantech DMS-BA16 board. The board is based on Advantech BA16 module which has a i.MX6D processor. The board supports: - FEC Ethernet - USB Ports - SDHC and MMC boot - SPI NOR - LVDS and HDMI display Basic information about the module: - Module manufacturer: Advantech - CPU: Freescale ARM Cortex-A9 i.MX6D - SPECS: Up to 2GB Onboard DDR3 Memory; Up to 16GB Onboard eMMC NAND Flash Supports OpenGL ES 2.0 and OpenVG 1.1 HDMI, 24-bit LVDS 1x UART, 2x I2C, 8x GPIO, 4x Host USB 2.0 port, 1x USB OTG port, 1x micro SD (SDHC),1x SDIO, 1x SATA II, 1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2 Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Cc: u-boot@lists.denx.de Cc: sbabic@denx.de
* | ARM: am335x: select DM_GPIOMasahiro Yamada2016-09-07-0/+1
| | | | | | | | | | | | | | | | We are supposed to not add config entries with only "default y" in board/SoC Kconfig files. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
* | ARM: armv7: move ARMV7_PSCI_NR_CPUS to KconfigMasahiro Yamada2016-09-07-0/+9
| | | | | | | | | | | | | | | | | | | | | | Move this option to Kconfig and set its default value to 4; this increases the number of supported CPUs for some boards. It consumes 1KB memory per CPU for PSCI stack, but it should not be a big deal, given the amount of memory used for the modern OSes. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | ARM: armv7: move CONFIG_ARMV7_PSCI to KconfigMasahiro Yamada2016-09-07-0/+16
| | | | | | | | | | | | | | | | | | Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms can select. Then, move CONFIG_ARMV7_PSCI, which is automatically enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | ARM: armv7: guard memory reserve for PSCI with #ifdef CONFIG_ARMV7_PSCIMasahiro Yamada2016-09-07-2/+2
| | | | | | | | | | | | | | | | If CONFIG_ARMV7_NONSEC is enabled, the linker script requires CONFIG_ARMV7_PSCI_NR_CPUS regardless of CONFIG_ARMV7_PSCI. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | ARM: tegra: remove wrong dependency on SPL_BUILDMasahiro Yamada2016-09-07-2/+2
| | | | | | | | | | | | | | SPL_BUILD is not a CONFIG in Kconfig, so !SPL_BUILD is always true. Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | TI: Rework SRAM definitions and maximumsTom Rini2016-09-06-10/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On all TI platforms the ROM defines a "downloaded image" area at or near the start of SRAM which is followed by a reserved area. As it is at best bad form and at worst possibly harmful in corner cases to write in this reserved area, we stop doing that by adding in the define NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this. At current we define the end of scratch space at 0x228 bytes past the start of scratch space this this gives us a lot of room to grow. As these scratch uses are non-optional today, all targets are modified to respect this boundary. Tested on OMAP4 Pandaboard, OMAP3 Beagle xM Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Paul Kocialkowski <contact@paulk.fr> Cc: Enric Balletbo i Serra <eballetbo@gmail.com> Cc: Adam Ford <aford173@gmail.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Thomas Weber <weber@corscience.de> Cc: Hannes Schmelzer <oe5hpm@oevsv.at> Cc: Thomas Chou <thomas@wytron.com.tw> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Sam Protsenko <semen.protsenko@linaro.org> Cc: Heiko Schocher <hs@denx.de> Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Cc: Ben Whitten <ben.whitten@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: "B, Ravi" <ravibabu@ti.com> Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Ash Charles <ashcharles@gmail.com> Cc: "Kipisz, Steven" <s-kipisz2@ti.com> Cc: Daniel Allred <d-allred@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Ladislav Michl <ladis@linux-mips.org>
* | meson: odroid-c2: enable Ethernet support through the device treeBeniamino Galvani2016-09-06-3/+0
| | | | | | | | | | | | | | | | Remove the device definition from board file, update the driver with the new compatible property and update config with necessary options. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | arm: dts: update DTS files for meson-gxbb and odroid-c2Beniamino Galvani2016-09-06-1/+188
| | | | | | | | | | | | | | Import DTS files and dt-bindings includes from Linux 4.8-rc1. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | bcm2835_gpio: Implement GPIOF_FUNCAlexander Graf2016-09-06-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | So far we could only tell the gpio framework that a GPIO was mapped as input or output, not as alternative function. This patch adds support for determining whether a function is mapped as alternative. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
* | Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2016-09-06-51/+440
|\ \
| * | sunxi: Add defconfig and dts file for the Orange Pi Plus2E SBCHans de Goede2016-09-03-1/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus, with 2G RAM and an external gbit ethernet phy. The dts file is identical to the one submitted to the upstream kernel, except that it has the pending patch to enable the ethernet controller squashed in, as u-boot already has sun8i-emac support. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | sunxi: Sync h3-orangepi dts files with kernelHans de Goede2016-09-03-47/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds an emac node to the orangepi-2 dts (not yet merged upstream, but in u-boot we already have emac support); fixes the alphetically sorting of nodes in sun8i-h3-orangepi-plus.dts and disables some usb controllers in sun8i-h3-orangepi-plus.dts which are only used on the plus2e, as upstream has decided to do a separate dts files for the plus2e. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | sunxi: Fix H3 EMAC syscon register addressChen-Yu Tsai2016-09-03-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The sun8i-emac driver follows an old version of the proposed DT bindings, where the EMAC clock and EPHY control register range is listed directly, rather than through a syscon phandle. Add back the syscon register range to avoid an invalid data access. We should fix the driver once the Linux kernel bindings have been finalized. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | sunxi: Add support for A33-OLinuXino boardStefan Mavrodiev2016-09-03-0/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A33-OLinuXino is A33 development board designed by Olimex LTD. It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector, headphone and mic jacks, connector for LiPo battery and optional 4GB NAND Flash. It has two 40-pin headers. One for LCD panel, and one for additional modules. Also there is CSI/DSI connector. The dts files are identical to the ones submitted to the upstream kernel. Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | sunxi: add proper device tree for iNet D978 rev2 boardsIcenowy Zheng2016-09-03-0/+89
| |/ | | | | | | | | | | | | | | Add a proper dts for the iNet D978 rev2 based A33 tablets. Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | ARM: dts: dra72-evm: fix broken ethernetMugunthan V N2016-09-06-1/+1
|/ | | | | | | | | | | With commit ceec08f50b6, phy is connected to slave 0, but changing the phy node was missed, fix it by populating the phy node to proper cpsw slave node. Fixes: ceec08f50b6 ("ARM: dts: dra72-evm: Add mode-gpios entry for mac node") Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Cc: Vignesh R <vigneshr@ti.com> Tested-by: Tom Rini <trini@konsulko.com>
* ARM: tegra: Add support for TK1-SOM board from Colorado EngineeringPeter Chubb2016-09-01-0/+490
| | | | | | | | | | | | | | The Colorado TK1 SOM is a small form factor board similar to the Jetson TK1. The main differences lie in the pinmux, and in that the PCIe controller is set to use in 4lanes+1lane, rather than 2+2. The pinmux header here was generated from a spreadsheet provided by Colorado Engineering using the tegra-pinmux scripts. The spreadsheet was converted from v09 to v11 by me. Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: use numeric versioning for p2771-0000Stephen Warren2016-08-30-6/+6
| | | | | | | | | | | | | | | | | The board ID EEPROM and board ID stickers on p2771-0000 will use a numeric versioning scheme, with version numbers such as 000/100/200/300/400/500. Within NVIDIA, these versions are also known as A00/A01/A02/A03/A04/B00. However, that numbering scheme is not easily visible outside of NVIDIA, and so does not make much sense to use. Convert U-Boot to use the readily visible numeric scheme. Also, it turns out that the current A02 DT actually applies to board versions 000/100/200 (A00..A02). Consequently rename this to 000 not 200 so that all U-Boot builds are named after the first version of the HW they support. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini2016-08-28-4/+35
|\
| * ARM: dts: uniphier: add u-boot, dm-pre-reloc to use eMMC boot on sLD3Masahiro Yamada2016-08-28-0/+9
| | | | | | | | | | | | | | The eMMC on sLD3 is assigned with dedicated pins (only multiplexed with GPIO), so it shouldn't hurt to enable eMMC on SPL all the time. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
| * ARM: uniphier: display revision of Micro Support Card 3.6.x kindlyMasahiro Yamada2016-08-28-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The revision of the original support card (rev 3.5, rev 3.6) fits in the 8 bit width revision register. When it was extended in a weird way, it was versioned in the format of "3.6.x" (where it should have been "3.7", of course). What is worse, only the sub-level version "6.x" was recorded in the 8 bit width register, completely ignoring the compatibility of the revision register format. This patch saves madly-versioned support cards by assuming the major version "3" when the MSB 4 bit of the register is read as "6". With this, the support card revision that were displayed as "6.10" is now corrected to "3.6.10". Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
| * ARM: uniphier: support system reset functionality for PSCIMasahiro Yamada2016-08-28-2/+17
| | | | | | | | | | | | | | | | | | | | This supports the system reset via PSCI for ARMv7 SoCs. Because the system reset is not supported on PSCI 0.1, let's define CONFIG_ARMV7_PSCI_1_0. (it is supported since PSCI 0.2, but there is no CONFIG to enable it in U-Boot for now.) Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2016-08-26-2193/+3539
|\ \
generated by cgit v1.1 at 2024-11-06 06:31:43 +0000