summaryrefslogtreecommitdiff
path: root/arch/arm
Commit message (Collapse)AuthorAgeLines
* ARM V7 (OMAP): add data cache support, test on Beagle boardHeiko Schocher2010-09-19-0/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add data cache support for ARM V7 systems. Used cache flush functions from linux:arch/arm/mm/cache-v7.S developed from Catalin Marinas. Enable "cache" command on Beagle board and test performance. Test 1: Loading 127 MB of data from NAND flash into RAM: Instr. Cache off on on Data Cache off off on -------------------------------------------------- Beagle (Cortex A8) 116s 106s 30.3s = x 3.8 Test 2: uncompressing a gzipped image from RAM to RAM (size compressed: 6.5 MiB, uncompressed: 35 MiB): Instr. Cache off on on Data Cache off off on -------------------------------------------------- Beagle (Cortex A8) 1.84s 1.64s 0.12s = x 15.3 Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Ben Gardiner<bengardiner@nanometrics.ca>
* ARM (ARM926ejs): add data cache support, tested on magnesium and tx25 boardHeiko Schocher2010-09-19-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable "cache" command on tx25 and magnesium board and test performance. Test 1: Loading 127 MB of data from NAND flash into RAM: Instr. Cache off on on Data Cache off off on -------------------------------------------------- magnesium 32,6s 22,5s 30s = x 1,09 tx25 (29MB only) 9,69s 5,05s 8,16s = x 1,19 Test 2: uncompressing a gzipped image from RAM to RAM (size compressed: 6.5 MiB, uncompressed: 35 MiB): Instr. Cache off on on Data Cache off off on -------------------------------------------------- magnesium 4,25s 2,08s 1,72s = x 2,47 tx25 4,82s 2,04s 1,84s = x 2,62 Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Alessandro Rubini <rubini@gnudd.com>
* ARM: cp15: setup mmu and enable dcacheHeiko Schocher2010-09-19-0/+51
| | | | | | | | | | | | | | | | | | | | | This has been tested on at91sam9263 and STN8815. Again, I didn't check if it has bad effects on non-arm926 cores. Initially I had a "done" bit to only set up page tables at the beginning. However, since the aligmnent requirement was for the whole object file, this extra integer tool 16kB in BSS, so I chose to remove it. Also, note not all boards use PHYS_SDRAM, but it looks like it's the most used name (more than CONFIG_SYS_DRAM_BASE for example). Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Signed-off-by: Heiko Schocher <hs@denx.de>
* arm: get rid of bi_envHeiko Schocher2010-09-19-4/+0
| | | | | | | | | bi_env is nowhere used, so delete it! Signed-off-by: Heiko Schocher <hs@denx.de> similar patch posted from Dirk Behme Tue Jul 27 18:36:09 CEST 2010 http://lists.denx.de/pipermail/u-boot/2010-July/074542.html
* New implementation for internal handling of environment variables.Wolfgang Denk2010-09-19-6/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Motivation: * Old environment code used a pessimizing implementation: - variable lookup used linear search => slow - changed/added variables were added at the end, i. e. most frequently used variables had the slowest access times => slow - each setenv() would calculate the CRC32 checksum over the whole environment block => slow * "redundant" envrionment was locked down to two copies * No easy way to implement features like "reset to factory defaults", or to select one out of several pre-defined (previously saved) sets of environment settings ("profiles") * No easy way to import or export environment settings ====================================================================== API Changes: - Variable names starting with '#' are no longer allowed I didn't find any such variable names being used; it is highly recommended to follow standard conventions and start variable names with an alphanumeric character - "printenv" will now print a backslash at the end of all but the last lines of a multi-line variable value. Multi-line variables have never been formally defined, allthough there is no reason not to use them. Now we define rules how to deal with them, allowing for import and export. - Function forceenv() and the related code in saveenv() was removed. At the moment this is causing build problems for the only user of this code (schmoogie - which has no entry in MAINTAINERS); may be fixed later by implementing the "env set -f" feature. Inconsistencies: - "printenv" will '\\'-escape the '\n' in multi-line variables, while "printenv var" will not do that. ====================================================================== Advantages: - "printenv" output much better readable (sorted) - faster! - extendable (additional variable properties can be added) - new, powerful features like "factory reset" or easy switching between several different environment settings ("profiles") Disadvantages: - Image size grows by typically 5...7 KiB (might shrink a bit again on systems with redundant environment with a following patch series) ====================================================================== Implemented: - env command with subcommands: - env print [arg ...] same as "printenv": print environment - env set [-f] name [arg ...] same as "setenv": set (and delete) environment variables ["-f" - force setting even for read-only variables - not implemented yet.] - end delete [-f] name not implemented yet ["-f" - force delete even for read-only variables] - env save same as "saveenv": save environment - env export [-t | -b | -c] addr [size] export internal representation (hash table) in formats usable for persistent storage or processing: -t: export as text format; if size is given, data will be padded with '\0' bytes; if not, one terminating '\0' will be added (which is included in the "filesize" setting so you can for exmple copy this to flash and keep the termination). -b: export as binary format (name=value pairs separated by '\0', list end marked by double "\0\0") -c: export as checksum protected environment format as used for example by "saveenv" command addr: memory address where environment gets stored size: size of output buffer With "-c" and size is NOT given, then the export command will format the data as currently used for the persistent storage, i. e. it will use CONFIG_ENV_SECT_SIZE as output block size and prepend a valid CRC32 checksum and, in case of resundant environment, a "current" redundancy flag. If size is given, this value will be used instead of CONFIG_ENV_SECT_SIZE; again, CRC32 checksum and redundancy flag will be inserted. With "-b" and "-t", always only the real data (including a terminating '\0' byte) will be written; here the optional size argument will be used to make sure not to overflow the user provided buffer; the command will abort if the size is not sufficient. Any remainign space will be '\0' padded. On successful return, the variable "filesize" will be set. Note that filesize includes the trailing/terminating '\0' byte(s). Usage szenario: create a text snapshot/backup of the current settings: => env export -t 100000 => era ${backup_addr} +${filesize} => cp.b 100000 ${backup_addr} ${filesize} Re-import this snapshot, deleting all other settings: => env import -d -t ${backup_addr} - env import [-d] [-t | -b | -c] addr [size] import external format (text or binary) into hash table, optionally deleting existing values: -d: delete existing environment before importing; otherwise overwrite / append to existion definitions -t: assume text format; either "size" must be given or the text data must be '\0' terminated -b: assume binary format ('\0' separated, "\0\0" terminated) -c: assume checksum protected environment format addr: memory address to read from size: length of input data; if missing, proper '\0' termination is mandatory - env default -f reset default environment: drop all environment settings and load default environment - env ask name [message] [size] same as "askenv": ask for environment variable - env edit name same as "editenv": edit environment variable - env run same as "run": run commands in an environment variable ====================================================================== TODO: - drop default env as implemented now; provide a text file based initialization instead (eventually using several text files to incrementally build it from common blocks) and a tool to convert it into a binary blob / object file. - It would be nice if we could add wildcard support for environment variables; this is needed for variable name auto-completion, but it would also be nice to be able to say "printenv ip*" or "printenv *addr*" - Some boards don't link any more due to the grown code size: DU405, canyonlands, sequoia, socrates. => cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>, Stefan Roese <sr@denx.de>, Heiko Schocher <hs@denx.de> - Dropping forceenv() causes build problems on schmoogie => cc: Sergey Kubushyn <ksi@koi8.net> - Build tested on PPC and ARM only; runtime tested with NOR and NAND flash only => needs testing!! Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>, Cc: Stefan Roese <sr@denx.de>, Cc: Heiko Schocher <hs@denx.de> Cc: Sergey Kubushyn <ksi@koi8.net>
* Make getenv() work before relocation.Wolfgang Denk2010-09-19-8/+3
| | | | | | | | | | | | | | | | | | | So far, getenv() would work before relocation is most cases, even though it was not intended to be used that way. When switching to a hash table based implementation, this would break a number of boards. For convenience, we make getenv() check if it's running before relocation and, if so, use getenv_f() internally. Note that this is limited to simple cases, as we use a small static buffer (32 bytes) in the global data for this purpose. For this reason, it is also not a good idea to convert all current uses of getenv_f() into getenv() - some of the existing use cases need to be able to deal with longer variable values, so getenv_f() is still needed and recommended for use before relocation. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Prepare v2010.09-rc2v2010.09-rc2Wolfgang Denk2010-09-19-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Save environment data to mmc.Terry Lv2010-09-19-5/+10
| | | | | | | | This patch is to save environment data to mmc card. It uses interfaces defined in generic mmc. Signed-off-by: Terry Lv <r65388@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* ARM: Update ARM mach-typesThomas Weber2010-09-18-4/+1226
| | | | | | This patch updates the mach-types.h based on the latest linux kernel Signed-off-by: Thomas Weber <weber@corscience.de>
* Prepare v2010.09-rc1v2010.09-rc1Wolfgang Denk2010-09-10-7/+0
| | | | | | Coding style cleanup. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-tiWolfgang Denk2010-09-09-296/+754
|\
| * ARMV7: OMAP3: Remove erroneous hard coded sdram setup for 128MB/bankSteve Sakoman2010-09-08-22/+21
| | | | | | | | | | | | | | | | | | Upcoming Beagle and Overo revisions use POP memory with 256MB or 512MB per bank. This patches uses the SDRC settings from x-load or the config header to set up timing properly. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * ARMV7: OMAP3: Fix broken reset command on OMAP36XX/37XX and OMAP4Steve Sakoman2010-09-08-1/+5
| | | | | | | | | | | | | | | | Using the reset command on OMAP36XX/37XX and OMAP4 caused a hang. This patch uses the reset bit appropriate for each CPU architecture. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * ARMV7: OMAP3: Apply Cortex-A8 errata workarounds only on affected revisionsMans Rullgard2010-09-08-3/+10
| | | | | | | | | | | | | | | | | | | | The workarounds for errata 621766 and 725233 should only be applied on affected Cortex-A8 revisions. Recent chips use r3px cores where these have been fixed. Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * ARMV7: OMAP3: Convert setup_auxcr() to pure asmMans Rullgard2010-09-08-35/+19
| | | | | | | | | | | | | | | | | | | | | | This function consists entirely of inline asm statements, so writing it directly in a .S file is simpler. Additionally, the inline asm is not safe as is, since registers are not guaranteed to be preserved between asm() statements. Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * ARMV7: OMAP3: Fix and clean up L2 cache enable/disable functionsMans Rullgard2010-09-08-54/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On OMAP34xx ES1.0, the L2 enable bit can only be set in secure mode, so an SMC call to the ROM monitor is required. On later versions, and on newer devices, this bit is banked and we can set it directly. The code checked only the ES revision of the chip, and hence incorrectly used the ROM call on ES1.0 versions of other devices. This patch adds a check for chip family as well as revision, and also removes some code duplication between the enable and disable functions. Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * ARMV7: OMAP3: Add clock setup for OMAP36XX/37XXSteve Sakoman2010-09-08-147/+515
| | | | | | | | | | | | | | | | This patch configures clocks properly when a 36XX/37XX processor is detected. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * ARMV7: OMAP3: Update CPU type detection for AM35XX/OMAP36XX/37XXSteve Sakoman2010-09-08-34/+161
| | | | | | | | | | | | | | | | TI has added new processors to the OMAP3 family. This patch enhances the code in sysinfo.c to detect which family member is present. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * ARMV7: OMAP: Move syslib.c to omap-common since it can be shared by OMAP3 ↵Steve Sakoman2010-09-08-3/+5
| | | | | | | | | | | | | | | | | | | | and OMAP4 The functions in syslib.c can be shared, so this patch moves it from cpu/omap3 to cpu/omap-common Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | Merge branch 'at91' of git://git.denx.de/u-boot-atmelWolfgang Denk2010-09-08-29/+525
|\ \
| * | at91_pit: Fix AT91_PIT_MR_PIV_MASK macroAlexander Stein2010-09-03-1/+1
| | | | | | | | | | | | Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
| * | AT91: add option to enable pullups in at91sam9260_devices.cReinhard Meyer2010-09-03-10/+25
| | | | | | | | | | | | Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
| * | AT91: reset.c: fix comments, add optionReinhard Meyer2010-09-03-10/+11
| | | | | | | | | | | | Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
| * | AT91: fix at91sam9260.h for AT91SAM9XEReinhard Meyer2010-09-03-4/+14
| | | | | | | | | | | | | | | | | | | | | Define the different location of the GPBRs for the 9XE Define the proper CPU Name Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
| * | AT91SAM9XE: add embedded flash supportReinhard Meyer2010-09-03-0/+364
| | | | | | | | | | | | Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
| * | AT91: add RTT and GPBR based RTCReinhard Meyer2010-09-03-0/+81
| | | | | | | | | | | | Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
| * | AT91: MCI: add SD/MMC driver using mmc frameworkReinhard Meyer2010-09-03-0/+28
| | | | | | | | | | | | Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
| * | AT91 Fix: return value of get_tbclkJens Scharsig2010-08-31-4/+1
| | | | | | | | | | | | | | | | | | | | | * Fix: return value of get_tbclk * this fixes issue with prematurely restart/retry, if BOOT_RETRY_TIMEOUT is used Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* | | Merge branch 'master' of git://git.denx.de/u-boot-samsungWolfgang Denk2010-09-08-144/+229
|\ \ \
| * | | ARMV7: S5P: rename the member of gpio structureMinkyu Kang2010-08-30-86/+86
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Typically we declare the name of gpio structure to "gpio", so it was duplicated around the name. (e.g: gpio->gpio_a) This patch modified the naming that is removing "gpio_". Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
| * | | ARMV7: S5P: separate the peripheral clocksMinkyu Kang2010-08-30-6/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Because of peripheral devices can select clock sources, separate the peripheral clocks. (pwm, uart and so on) It just return the pclk at s5pc1xx SoC, but s5pc210 SoC must be calculated by own clock register setting. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
| * | | ARMV7: S5P: fix the macro at samsung_get_base functionMinkyu Kang2010-08-26-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | New line is unnecessary at last line of macro. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | S5P: mmc: fix the mmc offsetMinkyu Kang2010-08-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | This patch fixed the size of mmc structure. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | | ARMV7: S5P: rename from s5pc1xx to s5pMinkyu Kang2010-08-23-22/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Because of these are common files around s5p Socs, rename from s5pc1xx to s5p. And getting cpu_id is SoC specific, so move to SoC's header file. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
| * | | ARMV7: S5P: make s5p-common for sharing the code between s5pc1xx and s5pc2xxMinkyu Kang2010-08-23-2/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds basic support for s5pc210. s5p-common will be used by all of s5p SoCs. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
| * | | S5P: Use accessor functions instead of SoC specific defines to access the ↵Minkyu Kang2010-08-17-29/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | base address This patch is intended to prepare the other S5P SoC. (s5pc210) If use SoC specific defines then can't share with other SoC. So, make the accessor functions for access the base address by common way. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-marvellWolfgang Denk2010-09-07-3/+3
|\ \ \ \
| * | | | orion5x: fix comment-in-comment typo in cpu.hAlbert Aribaud2010-08-27-1/+1
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
| * | | | Kirkwood: bugfix: window size (mis)calculationPrafulla Wadaskar2010-08-26-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixed kw_winctrl_calcsize() off-by-1 bug which caused mapping windows size to be cut by half. This corrected all windows address configuration Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| * | | | Orion5x: bugfix: window size (mis)calculationAlbert Aribaud2010-08-26-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix orion5x_winctrl_calcsize() off-by-1 bug which caused mapping windows to be cut by half. This afected all windows including NOR flash (causing half the flash to be unaccessible) but DRAM was and still is fine as its size is determined otherwise. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
* | | | | Merge branch 'master' of /home/wd/git/u-boot/masterWolfgang Denk2010-09-07-107/+3
|\ \ \ \ \ | |/ / / / |/| | | / | | |_|/ | |/| |
| * | | omap2: i2c: remove redundant header definitionsNishanth Menon2010-08-23-106/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove the register offset and common defines which are already present in drivers/i2c/omap24xx.h. All of these defines carry the same value even. Cc: Steve Sakoman <steve@sakoman.com> Cc: Heiko <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Wolfang Denk <wd@denx.de> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Steve Sakoman <steve@sakoman.com>
| * | | omap2: i2c: add syss offsetNishanth Menon2010-08-23-1/+3
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OMAP2420 ES2.3 trm defines syss register offset as 0x10. Add it. Cc: Steve Sakoman <steve@sakoman.com> Cc: Heiko <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Wolfang Denk <wd@denx.de> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Steve Sakoman <steve@sakoman.com>
* | | Merge branch 'master' of /home/wd/git/u-boot/masterWolfgang Denk2010-08-18-24/+1168
|\ \ \ | |/ /
| * | ARM: Update ARM mach-typesSandeep Paulraj2010-08-18-24/+1116
| | | | | | | | | | | | | | | | | | This patch updates the mach-types.h based on the latest linux kernel Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | AM35x: Adding SCM general register definitionsAjay Kumar Gupta2010-08-12-0/+52
| | | | | | | | | | | | | | | | | | | | | | | | Adding general register structure of system control module (SCM) of AM35x. This would be required to access devconf2 and ip_sw_reset register in musb module. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-tiWolfgang Denk2010-08-12-6/+6
|\ \ \ | |/ /
| * | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-08-10-59/+682
| |\ \
| * | | miiphy: constify device nameMike Frysinger2010-08-09-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The driver name does not need to be writable, so constify it. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* | | | ARM: Add support for MB86R0x SoCsMatthias Weisser2010-08-10-0/+950
| |/ / |/| | | | | | | | Signed-off-by: Matthias Weisser <weisserm@arcor.de>
generated by cgit v1.1 at 2024-12-24 17:14:22 +0000