summaryrefslogtreecommitdiff
path: root/arch/arm
Commit message (Collapse)AuthorAgeLines
* am33xx: Convert to using <asm/emif.h> to describe the EMIFTom Rini2012-09-01-41/+15
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Remove DMM_BASE defineTom Rini2012-09-01-1/+0
| | | | | | The am33xx does not have a DMM, so don't define the base. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Enable gpio0 clockTom Rini2012-09-01-0/+4
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* OMAP3: mem: Add Numonyx OneNAND 200MHz timing informationJavier Martinez Canillas2012-09-01-0/+29
| | | | Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
* am33xx: pin mux defintions for CPSW switchChandan Nath2012-09-01-0/+2
| | | | | | | | | This patch adds pin mux settings for CPSW switch found on TI AM335X based boards (MII and RGMII modes). Signed-off-by: Chandan Nath <chandan.nath@ti.com> [Ilya: split pinmux into separate patch] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* am33xx: CPSW init and definitionsChandan Nath2012-09-01-1/+23
| | | | | | | | | This patch adds platform-specific initialization for CPSW switch on TI AM33XX SoCs. Signed-off-by: Chandan Nath <chandan.nath@ti.com> [Ilya: split init out of original patch] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* arm/davinci/da850: add uart0 pinmuxMikhail Kshevetskiy2012-09-01-0/+7
| | | | | Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com> Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
* arm/davinci: fix DDR2/mDDR memory controller initialization for Omap L138Mikhail Kshevetskiy2012-09-01-7/+20
| | | | | | | | | follow section 15.2.13.1 (Initializing Following Device Power Up or Reset) of OMAP-L138 DSP+ARM Processor Technical Reference Manual Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com> Acked-by: Christian Riesch <christian.riesch@omicron.at> Tested-by: Christian Riesch <christian.riesch@omicron.at>
* Revert "arm: armv7: add compile option -mno-unaligned-access if available"Albert ARIBAUD2012-09-01-2/+0
| | | | | | This reverts commit 5347560f5427bcdd48a563b62180481606ac8044, which was applied only to get release 2012.07 functional on as many ARM targets as possible despite mis-aligned accesses.
* omap: am335x_evm: enable i2c1 channelSteve Sakoman2012-09-01-0/+5
| | | | | | | This patch sets up pinmux, enables fclk, and defines CONFIG_I2C_MULTI_BUS Signed-off-by: Steve Sakoman <steve@sakoman.com>
* da850/omap-l138: Add support to read u-boot image from MMC/SDLad, Prabhakar2012-09-01-0/+5
| | | | | | | | | | | | | | | DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will be in SPI flash and U-Boot image will be in MMC/SD card. SPL will do the low level initialization and then loads the u-boot image from MMC/SD card. Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138 configuration file to enable this feature. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
* arm, davinci: perform check for initializing global data and serial initLad, Prabhakar2012-09-01-6/+9
| | | | | | | | | | | initialize baudrate, flags, data and serial initialization, only when CONFIG_SPL_LIBCOMMON_SUPPORT is defined. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com> Acked-by: Christian Riesch <christian.riesch@omicron.at>
* da850/omap-l138: Add MMC support for DA850/OMAP-L138Lad, Prabhakar2012-09-01-0/+15
| | | | | | | | | This patch adds support for MMC/SD on DA850/OMAP-L138. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
* omap: am33xx: enable gpio supportSteve Sakoman2012-09-01-1/+75
| | | | | | | | | | | This patch uses the code in omap-common to support gpio modules 1-3 on am33xx based boards. It adds base address and register definitions, enables clocks to the modules, and enables building the common gpio code for CONFIG_AM33XX as well as CONFIG_OMAP Signed-off-by: Steve Sakoman <steve@sakoman.com>
* Consolidate bootcount code into drivers/bootcountStefan Roese2012-09-01-85/+1
| | | | | | | | | | | | | | | | | | | This patch moves all bootcount implementations into a common directory: drivers/bootcount. The generic bootcount driver is now usable not only by powerpc platforms, but others as well. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Manfred Rudigier <manfred.rudigier@omicron.at> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de> Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com> Tested-by: Christian Riesch <christian.riesch@omicron.at> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
* global_data: unify global flag definesMike Frysinger2012-08-09-13/+1
| | | | | | | All the global flag defines are the same across all arches. So unify them in one place, and add a simple way for arches to extend for their needs. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* I2C: Move struct s3c24x0_i2c to a common place.Rajeshwari Shinde2012-07-31-10/+0
| | | | | | | | | | struct s3c24x0_i2c is being moved to common local header file so that the same can be used by s3c series and exynos series SoCs. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
* EXYNOS: PINMUX: Add pinmux support for I2CRajeshwari Shinde2012-07-31-0/+60
| | | | | | | This patch adds pinmux code for I2C. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
* EXYNOS5: define EXYNOS5_I2C_SPACINGRajeshwari Shinde2012-07-31-0/+2
| | | | | | | | This patch defined EXYNOS5_I2C_SPACING used to calculate I2C channel base address. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
* EXYNOS: Add I2C base address.Rajeshwari Shinde2012-07-31-0/+3
| | | | | | | | This patch adds the base address for I2C. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
* EXYNOS: CLK: Add i2c clockRajeshwari Shinde2012-07-31-0/+34
| | | | | | | | | This adds i2c clock information for EXYNOS5. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
* imx-common: add i2c.c for bus recovery supportTroy Kisky2012-07-31-1/+186
| | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* i.mx53: add definition for I2C3_BASE_ADDRTroy Kisky2012-07-31-0/+1
| | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* i.mx: iomux-v3.c: move to imx-common directoryTroy Kisky2012-07-31-2/+2
| | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* i.mx: iomux-v3.h: move to imx-common include directoryTroy Kisky2012-07-31-2/+2
| | | | Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* iomux-v3: remove include of mx6x_pins.hTroy Kisky2012-07-31-1/+0
| | | | | | | This include is not needed. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Jason Liu <r64343@freescale.com>
* ARM1136: Fix cache range checksBenoît Thébaudeau2012-07-21-3/+3
| | | | | | | | | | | | | | bad_cache_range actually returned true if the range was OK, but it was used according to its name, which resulted in all valid dcache range invalidate/flush operations being dropped. Hence, most DMA transfers resulted in garbage data. This patch renames this function according to what it does, and it fixes the interpretation of its return value by other functions. The chosen naming is the same as for ARM926EJ-S in order to be consistent. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Stefano Babic <sbabic@denx.de>
* mx6: Make pad name macro consistent with the datasheetAshok2012-07-20-2/+2
| | | | | | | | Use the same name as defined in the datasheet. DSP_CLK -> DISP_CLK Signed-off-by: Ashok Kumar Reddy Kourla <ashokkourla2000@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
* ARM: lib: Remove CONFIG_ARCH_CPU_INIT dependencyFabio Estevam2012-07-20-2/+8
| | | | | | | | | | | | Create a weak-aliased arch_cpu_init, so that we can get rid of CONFIG_ARCH_CPU_INIT and always call arch_cpu_init. This way we do not need to define CONFIG_ARCH_CPU_INIT in every board file, since arch_cpu_init() is supposed to handle common CPU level code. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* arm: armv7: add compile option -mno-unaligned-access if availableTetsuyuki Kobayashi2012-07-20-0/+2
| | | | | | | | | | Recent compiler generates unaligned memory access in armv7 default. But current U-Boot does not allow unaligned memory access, so it causes data abort exception. This patch add compile option "-mno-unaligned-access" if it is available. Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Tested-by: Gary Thomas <gary@mlbassoc.com>
* arm: Fix to mistake clean the memory spaceZhong Hongbo2012-07-20-40/+65
| | | | | | | | | | | In currently, when __bss_start is equal to __bss_end__, The bss loop will clear all the things in memory space. But just only when __bss_end__ greater than __bss_start__, we do the clear bss section operation. Signed-off-by: Zhong Hongbo <bocui107@gmail.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Merge branch 'next' of git://git.denx.de/u-boot-videoWolfgang Denk2012-07-18-2/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | * 'next' of git://git.denx.de/u-boot-video: ipu_common: Add ldb_clk for use in parenting the pixel clock ipu_common: Do not hardcode the ipu_clk frequency ipu_common: Rename MXC_CCM_BASE ipu_common: Let clk_ipu_enable/disable only run on MX51 and MX53 ipu_common: Only apply the erratum to MX51 video: Rename CONFIG_VIDEO_MX5 mx6: Allow mx6 to access the IPUv3 registers common lcd: minor coding style changes Signed-off-by: Wolfgang Denk <wd@denx.de>
| * mx6: Allow mx6 to access the IPUv3 registersFabio Estevam2012-07-10-2/+3
| | | | | | | | | | | | Adjust the IPUv3 registers, so that the IPUv3 driver can be extended for mx6 as well. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | mxc_i2c: specify i2c base address in config fileTroy Kisky2012-07-11-1/+8
|/ | | | | | | | | The following platforms had their config files changed flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd and mx53loco. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2012-07-10-2/+96
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: tegra: define fdt_load/fdt_high variables tegra: enable bootz command tegra: usb: Fix device enumeration problem of USB1 tegra: trimslice: set up serial flash pinmux tegra: add pin_mux_spi() board initialization function tegra: add GMC/GMD funcmux entry for SFLASH tegra: bootcmd: start USB only when needed tegra: bootcmd enhancements tegra: add enterrcm command tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG Add env vars describing U-Boot target board tegra: usb: fix wrong error check tegra: add ULPI on USB2 funcmux entry tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches tegra: Add Tamonten Evaluation Carrier support tegra: Use SD write-protect GPIO on Tamonten tegra: Implement gpio_early_init() on Tamonten tegra: Allow boards to perform early GPIO setup tegra: plutux: Add device tree support tegra: medcom: Add device tree support tegra: Rework Tamonten support beagle: add eeprom expansion board info for bct brettl4 Signed-off-by: Wolfgang Denk <wd@denx.de>
| * tegra: usb: Fix device enumeration problem of USB1Jim Lin2012-07-09-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | A known hardware issue of USB1 port where bit 1 (connect status change) of PORTSC register will be set after issuing Port Reset (like "usb reset" in u-boot command line). This will be treated as an error and stops later device enumeration. Therefore we clear that bit after Port Reset in order to proceed later device enumeration. Signed-off-by: Jim Lin <jilin@nvidia.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: add GMC/GMD funcmux entry for SFLASHStephen Warren2012-07-09-0/+13
| | | | | | | | | | | | | | This is used on TrimSlice. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: add enterrcm commandStephen Warren2012-07-09-0/+66
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tegra's boot ROM supports a mode whereby code may be downloaded and flash programmed over a USB connection. On dev boards, this is typically entered by holding down a "force recovery" button and resetting the CPU. However, not all boards have such a button (one example is the Compulab Trimslice), so a method to enter RCM from software is useful. This change implements the command "enterrcm" to do this, and enables it for all Tegra boards by default. Even on boards other than Trimslice, controlling this over a UART may be useful, e.g. to allow simple remote control without the need for mechanical button actuators, or hooking up relays/... to the button. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: usb: fix wrong error checkLucas Stach2012-07-09-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | loop_count runs down from 10000, so the correct condition to error out is ==0. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren.nvidia@gmail.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: add ULPI on USB2 funcmux entryLucas Stach2012-07-09-1/+15
| | | | | | | | | | | | | | | | | | | | | | This is needed as a prerequisite for Tegra USB ULPI support within U-Boot. Signed-off-by: Lucas Stach <dev@lynxeye.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> CC: Stephen Warren <swarren@wwwdotorg.org> CC: Tom Warren <twarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | EXYNOS: Fix USB compiler warningRajeshwari Shinde2012-07-10-1/+0
| | | | | | | | | | | | | | Fixed the compiler warning message. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Marek Vasut <marex@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-usbWolfgang Denk2012-07-09-7/+684
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-usb: CONFIG: EXYNOS5: USB: Enable USB 2.0 on smdk5250 EXYNOS5: USB: Fix incorrect USB base addresses EXYNOS: Add power Enable/Disable for USB-EHCI USB: EXYNOS: Set USB 2.0 HOST Link mode EXYNOS5: Add structure for PMU registers EXYNOS5: Fix system register structure USB: EXYNOS: Incorporate EHCI review comments Signed-off-by: Wolfgang Denk <wd@denx.de>
| * EXYNOS5: USB: Fix incorrect USB base addressesRajeshwari Shinde2012-07-09-2/+2
| | | | | | | | | | | | | | | | | | This patch corrects the base addresses for USB_PHY and USB_OTG. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
| * EXYNOS: Add power Enable/Disable for USB-EHCIRajeshwari Shinde2012-07-09-0/+26
| | | | | | | | | | | | | | | | | | This patch adds functions to enable/disable the power of USB host controller for EXYNOS5. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
| * USB: EXYNOS: Set USB 2.0 HOST Link modeRajeshwari Shinde2012-07-09-0/+25
| | | | | | | | | | | | | | This patch adds a function to set usb host mode to USB 2.0 HOST Link for EXYNOS5 Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
| * EXYNOS5: Add structure for PMU registersRajeshwari Shinde2012-07-09-0/+622
| | | | | | | | | | | | | | | | This patch adds power mananagement registers structure for exynos5 SoC. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Chander Kashyap <chander.kashyap@linaro.org> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
| * EXYNOS5: Fix system register structureRajeshwari Shinde2012-07-09-0/+1
| | | | | | | | | | | | | | | | | | This patch corrects the SYSREG structure. We have removed the sysreg.h added in the previous patchset version as the sysreg structure is already defined in system.h. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
| * USB: EXYNOS: Incorporate EHCI review commentsRajeshwari Shinde2012-07-09-5/+8
| | | | | | | | | | | | | | This patch incorates the review comments given by Minkyu Kang for EHCI support on EXYNOS Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
* | Revert "arm: bugfix: save_boot_params_default accesses uninitalized stack ↵Wolfgang Denk2012-07-09-7/+1
|/ | | | | | | | | | | when -O0" This reverts commit fa042186b932e9b9ee9a2fd8a04a3acf7c70d224. It causes build warnings like this: cpu.c:48:1: warning: -fstack-usage not supported for this target [enabled by default] Signed-off-by: Wolfgang Denk <wd@denx.de>
* ARM: cache: Move the cp15 CR register read before flushing the cache.SRICHARAN R2012-07-07-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following is the cleanup sequence in arch/arm/cpu/armv7/cpu.c int cleanup_before_linux(void) { ... ... dcache_disable(); v7_outer_cache_disable(); invalidate_dcache_all(); } 1) invalidate_dcache_all call expects that all the caches has been flushed, invalidated and there are no dirty entries prior to its execution. In the above sequence dcache_disable() flushes, invalidates the caches and turns off the mmu. But after it cleanups the cache and before the mmu is disabled there is a cp_delay() function which has STR instruction. On certain cores like the cortex-a15, cache hit and a write can happen to a cache line even when the dcache is disabled. So the above mentioned STR instruction creates a dirty entry after cleaning. The mmu gets disabled after this. 2) invalidate_dcache_all invalidates the cache lines. Again on cores like cortex-a15, invalidate instruction flushes the dirty line as well. So some times the dirty line from sequence 1 can corrupt the memory resulting in a crash. Fixing this by moving the get_cr() and cp_delay() calls before cleaning up the cache, thus avoiding the dirty entry. Signed-off-by: R Sricharan <r.sricharan@ti.com>
generated by cgit v1.1 at 2024-10-22 20:33:35 +0000