summaryrefslogtreecommitdiff
path: root/arch/arm
Commit message (Collapse)AuthorAgeLines
* socfpga: Fix SOCFPGA build error for Altera dev kitChin Liang See2014-08-29-1/+7
| | | | | | | | | | | | | To fix the build error when build for Altera dev kit, not virtual target. At same time, set the build for Altera dev kit as default instead virtual target. With that, U-Boot is booting well and SPL still lack of few drivers. Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Pavel Machek <pavel@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
* socfpga: fix clock manager register definitionPavel Machek2014-08-29-99/+105
| | | | | | | | | Structure defining clock manager hardware was wrong, leading to wrong registers being accessed and hang in MMC init. This fixes structure to match hardware. Signed-off-by: Pavel Machek <pavel@denx.de>
* arm: include config.h in arch/arm/lib/vectors.SChristian Riesch2014-08-29-0/+2
| | | | | | | | | | | config.h is required for CONFIG_SYS_DV_NOR_BOOT_CFG. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Heiko Schocher <hs@denx.de> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
* ARM:asm:io.h use static inlineJeroen Hofstee2014-08-29-6/+6
| | | | | | | | | | | When compiling u-boot with W=1 the extern inline void for read* is likely causing the most noise. gcc / clang will warn there is never a actual declaration for these functions. Instead of declaring these extern make them static inline so it is actually declared. cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* Merge branch 'master' of git://git.denx.de/u-boot-tiTom Rini2014-08-29-74/+170
|\
| * ARM: DRA: Enable VTT regulatorLokesh Vutla2014-08-25-0/+3
| | | | | | | | | | | | | | | | | | | | DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. Configuring gpio7_11. The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards, and left unused on previous boards, so it is safe enough to enable gpio on all DRA7 boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7: Enable software leveling for dra7Sricharan R2014-08-25-68/+32
| | | | | | | | | | | | | | | | | | | | Currently hw leveling is enabled by default on DRA7/72. But the hardware team suggested to use sw leveling as hw leveling is not characterized and seen some test case failures. So enabling sw leveling on all DRA7 platforms. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * keystone2: use EFUSE_BOOTROM information to configure PLLsVitaly Andrianov2014-08-25-0/+129
| | | | | | | | | | | | | | | | | | This patch reads EFUSE_BOOTROM register to see the maximum supported clock for CORE and TETRIS PLLs and configure them accordingly. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
| * board/ti/dra7xx: add support for parallel NORpekon gupta2014-08-25-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM. The Flash device is connected to GPMC controller on chip-select[0] and accessed as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and is CFI compatible. As multiple devices are share GPMC pins on this board, so following board settings are required to detect NOR device: SW5.1 (NAND_BOOTn) = OFF (logic-1) SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */ SW5.3 (eMMC_BOOTn) = OFF (logic-1) SW5.4 (QSPI_BOOTn) = OFF (logic-1) And also set appropriate SYSBOOT configurations: SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */ SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */ SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */ SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */ SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */ SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */ SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */ SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */ Also, following changes are required to enable NOR Flash support in dra7xx_evm board profile:
* | Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblazeTom Rini2014-08-29-20/+5
|\ \
| * | ARM: zynq: Remove spl.hMichal Simek2014-08-19-18/+2
| | | | | | | | | | | | | | | | | | | | | | | | Do not specify own zynq specific SPL macros because there is no need for that. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | ARM: zynq: Move ps7_init() out of spl.hMichal Simek2014-08-19-2/+2
| | | | | | | | | | | | | | | | | | | | | Prepare for spl.h removal. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | zynq: spl: Add vectors section to linker scriptPeter Crosthwaite2014-08-08-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The vectors section contains the _start symbol which is used as the program entry point. Add it to the linker script in same fashion as done for regular u-boot. This allows for correct generation of an spl elf with a non-zero entry point. A similar change was applied to sunxi platform in "sunxi: Fix u-boot-spl.lds to refer to .vectors" (sha1: 9e5f80d823e3fd2a685b10ecf02009e34b86cff9) This also allows for placement of the vector table at the hivecs location by setting the TEXT_BASE to 0xffff0000. Tested-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini2014-08-29-1/+217
|\ \ \
| * | | ARM: tegra: add Colibri T30 board supportStefan Agner2014-08-18-0/+103
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds board support for the Toradex Colibri T30 module. Working functions: - SD card boot - eMMC environment and boot - USB host/USB client (on the dual role port) - Network (via ASIX USB) Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | | ARM: tegra: Use mem size from MC rather than ODMDATAStephen Warren2014-08-18-1/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In at least Tegra124, the Tegra memory controller (MC) has a register that controls the memory size. Read this to determine the memory size rather than requiring this to be redundantly encoded into the ODMDATA. This way, changes to the BCT (i.e. MC configuration) automatically updated SW's view of the memory size, without requiring manual changes to the ODMDATA. Future work potentially required: * Clip the memory size to architectural limits; U-Boot probably doesn't and won't support either LPAE or Tegra's "swiss cheese" memory layout, at least one of which would be required for >2GB RAM. * Subtract out any carveout required by firmware on future SoCs. Based-on-work-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * | | ARM: tegra: Disable VPRBryan Wu2014-08-18-0/+97
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Tegra114 and Tegra124 platforms, certain display-related registers cannot be accessed unless the VPR registers are programmed. For bootloader, we probably don't care about VPR, so we disable it (which counts as programming it, and allows those display-related registers to be accessed). This patch is based on the commit 5f499646c83ba08079f3fdff6591f638a0ce4c0c in Chromium OS U-Boot project. Signed-off-by: Andrew Chew <achew@nvidia.com> Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com> Signed-off-by: Bryan Wu <pengw@nvidia.com> [acourbot: ensure write went through, vpr.c style changes] Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Terje Bergstrom <tbergstrom@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-08-29-26/+2265
|\ \ \
| * | | mx6sxsabresd: Add Ethernet supportFabio Estevam2014-08-20-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031. Add support for one FEC port initially. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | mx6sx: Adjust enable_fec_anatop_clock() for mx6soloxFabio Estevam2014-08-20-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | Configure and enable the ethernet clock for mx6solox. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | mx6sxsabresd: Convert to the new Kconfig styleFabio Estevam2014-08-20-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | mx6sxsabresd was not in the master branch when the conversion to the new Kconfig style happened, so convert it now so that it can build again. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | ARM: mx6: Handle the MMDCx_MDCTL COL field capricesMarek Vasut2014-08-20-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The COL field value cannot be easily calculated from the desired column number. Instead, there are special cases for that, see the datasheet, MMDCx_MDCTL field description, field COL . Cater for those special cases. Signed-off-by: Marek Vasut <marex@denx.de>
| * | | ARM: mx6: Prevent overflow in DRAM size detectionMarek Vasut2014-08-20-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MX6 DRAM controller can be configured to handle 4GiB of DRAM, but only 3840 MiB of that can be really used. In case the controller is configured to operate a 4GiB module, the imx_ddr_size() function will correctly compute that there is 4GiB of DRAM in the system. Firstly, the return value is 32-bit, so the function will effectively return zero. Secondly, the MX6 cannot address the full 4GiB, but only 3840MiB of all that. Thus, clamp the returned size to 3840MiB in such case. Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Tim Harvey <tharvey@gateworks.com>
| * | | ARM: mx5: Fix CHSCCDR nameMarek Vasut2014-08-20-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Fix the name of the CCM CHSCCDR register. Signed-off-by: Marek Vasut <marex@denx.de>
| * | | mx6: add support of multi-processor commandGabriel Huau2014-08-20-0/+108
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows u-boot to load different OS or Bare Metal application on different cores of the i.MX6 SoC. For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1. Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr> Acked-by: Stefano Babic <sbabic@denx.de>
| * | | Update aristainetos board to KconfigStefano Babic2014-08-13-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | aristainetos board was merged in u-boot-imx before Kconfig was integrated, but it is not yet mainline. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
| * | | Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic2014-08-11-16/+1233
| |\ \ \ | | |/ / | | | | | | | | | | | | | | | | | | | | Conflicts: boards.cfg Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | | mx6: crm_regs: Fix MXC_CCM_CIMR_MASK_PERIPH2_CLK_SEL_LOADEDFabio Estevam2014-08-08-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | According to the Reference Manual the 'mask_periph2_clk_sel_loaded' field of register CCM_CIMR corresponds to bit 19 so fix its definition accordingly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | mx6: crm_regs: Fix MXC_CCM_CLPCR_WB_PER_AT_LPM definitionFabio Estevam2014-08-08-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | According to the Reference Manual the 'wb_per_at_lpm' field of register CCM_CLPCR corresponds to bit 16 so fix its definition accordingly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | mx6: crm_regs: Fix CDCDR_SPDIF0_CLK_PODF mask and offsetFabio Estevam2014-08-08-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to the Reference Manual the 'spdif0_clk_podf' field of register CCM_CDCDR corresponds to bits 22, 23 and 24, so fix the mask and offset definitions accordingly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | mx6: imx-regs: Remove unused 'omux' field from iomux structFabio Estevam2014-08-08-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 'omux' field is not used anywhere and such layout is not valid for mx6solox. Instead of adding more ifdef's into the structure, let's simply remove this unused 'omux' field. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | | Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic2014-08-08-692/+3167
| |\ \ \
| * | | | i.MX6: add enable_spi_clk()Heiko Schocher2014-07-23-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | add enable_spi_clk(), so board code can enable spi clocks. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Stefano Babic <sbabic@denx.de>
| * | | | i.MX6: define struct pwm_regs and PWMCR_* definesHeiko Schocher2014-07-23-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | add defines for pwm modul found on imx6. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
| * | | | imx6: add gpr2 usb_otg_id iomux select control defineHeiko Schocher2014-07-23-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | add IOMUXC_GPR1_USB_OTG_ID_OFFSET and IOMUXC_GPR1_USB_OTG_ID_SEL_MASK define for the USB_OTG_ID_SEL bit. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
| * | | | mx6: Adjust the GPR offset for mx6soloxFabio Estevam2014-07-23-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On mx6solox there is an additional 0x4000 offset for the GPR registers. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | | | mx6: Remove duplication of iomuxc structureFabio Estevam2014-07-23-11/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is no need to keep iomuxc_base_regs structure as it serves the exact same purpose of the iomuxc structure, which is to provide access to the GPR registers. The additional fields of iomuxc_base_regs are not used. Other advantage of 'iomuxc' is that it has a shorter name and the variable declarations can fit into a single line. So remove iomuxc_base_regs structure and use iomuxc instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | | | mx6: soc: Do not apply the PFD erratum for mx6soloxFabio Estevam2014-07-23-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The PFD issue is not present on mx6solox, so skip it in this case. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | Merge branch 'master' of git://git.denx.de/u-bootStefano Babic2014-07-16-786/+4438
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> Conflicts: boards.cfg
| * | | | | mx6: clock: Do not enable sata and ipu clocksFabio Estevam2014-07-10-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mx6sx does not have sata nor ipu blocks, so do not handle such clocks. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | mx6sx: Add pin definitionsFabio Estevam2014-07-10-0/+1677
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the pin definitions for mx6sx. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | | | | mx6: Add support for the mx6solox variantFabio Estevam2014-07-10-7/+369
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mx6solox is the newest member of the mx6 family. Some of the new features on this variants are: - Cortex M4 microcontroller (besides the CortexA9) - Dual Gigabit Ethernet Add the initial support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* | | | | | Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2014-08-29-284/+351
|\ \ \ \ \ \
| * | | | | | sunxi: dram: Autodetect DDR3 bus width and densitySiarhei Siamashka2014-08-12-5/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the case if the 'dram_para' struct does not specify the exact bus width or chip density, just use a trial and error method to find a usable configuration. Because all the major bugs in the DRAM initialization sequence are now hopefully fixed, it should be safe to re-initialize the DRAM controller multiple times until we get it configured right. The original Allwinner's boot0 bootloader also used a similar autodetection trick. The DDR3 spec contains the package pinout and addressing table for different possible chip densities. It appears to be impossible to distinguish between a single chip with 16 I/O data lines and a pair of chips with 8 I/O data lines in the case if they provide the same storage capacity. Because a single 16-bit chip has a higher density than a pair of equivalent 8-bit chips, it has stricter refresh timings. So in the case of doubt, we assume that 16-bit chips are used. Additionally, only Allwinner A20 has all A0-A15 address lines and can support densities up to 8192. The older Allwinner A10 and Allwinner A13 can only support densities up to 4096. We deliberately leave out DDR2, dual-rank configurations and the special case of a 8-bit chip with density 8192. None of these configurations seem to have been ever used in real devices. And no new devices are likely to use these exotic configurations (because only up to 2GB of RAM can be populated in any case). This DRAM autodetection feature potentially allows to have a single low performance fail-safe DDR3 initialiazation for a universal single bootloader binary, which can be compatible with all Allwinner A10/A13/A20 based devices (if the ifdefs are replaced with a runtime SoC type detection). Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | | | | | sunxi: dram: Derive write recovery delay from DRAM clock speedSiarhei Siamashka2014-08-12-1/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The write recovery time is 15ns for all JEDEC DDR3 speed bins. And instead of hardcoding it to 10 cycles, it is possible to set tighter timings based on accurate calculations. For example, DRAM clock frequencies up to 533MHz need only 8 cycles for write recovery. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | | | | | sunxi: dram: Drop DDR2 support and assume only single rank DDR3 memorySiarhei Siamashka2014-08-12-22/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All the known Allwinner A10/A13/A20 devices are using just single rank DDR3 memory. So don't pretend that we support DDR2 or more than one rank, because nobody could ever test these configurations for real and they are likely broken. Support for these features can be added back in the case if such hardware actually exists. As part of this code cleanup, also replace division by 1024 with division by 1000 for the refresh timing calculations. This allows to use the original non-skewed tRFC timing table from the DRR3 spec and make code less confusing. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | | | | | sunxi: dram: Configurable DQS gating window mode and delaySiarhei Siamashka2014-08-12-1/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The hardware DQS gate training is a bit unreliable and does not always find the best delay settings. So we introduce a 32-bit 'dqs_gating_delay' variable, where each byte encodes the DQS gating delay for each byte lane. The delay granularity is 1/4 cycle. Also we allow to enable the active DQS gating window mode, which works better than the passive mode in practice. The DDR3 spec says that there is a 0.9 cycles preamble and 0.3 cycle postamble. The DQS window has to be opened during preamble and closed during postamble. In the passive window mode, the gating window is opened and closed by just using the gating delay settings. And because of the 1/4 cycle delay granularity, accurately hitting the 0.3 cycle long postamble is a bit tough. In the active window mode, the gating window is auto-closing with the help of monitoring the DQS line, which relaxes the gating delay accuracy requirements. But the hardware DQS gate training is still performed in the passive window mode. It is a more strict test, which is reducing the results variance compared to the training with active window mode. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | | | | | sunxi: dram: Add a helper function 'mctl_get_number_of_lanes'Siarhei Siamashka2014-08-12-14/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is going to be useful in more than one place. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | | | | | sunxi: dram: Improve DQS gate data training error handlingSiarhei Siamashka2014-08-12-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The stale error status should be cleared for all sun4i/sun5i/sun7i hardware and not just for sun7i. Also there are two types of DQS gate training errors ("found no result" and "found more than one possible result"). Both are handled now. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * | | | | | sunxi: dram: Use divisor P=1 for PLL5Siarhei Siamashka2014-08-12-17/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This configures the PLL5P clock frequency to something in the ballpark of 1GHz and allows more choices for MBUS and G2D clock frequency selection (using their own divisors). In particular, it enables the use of 2/3 clock speed ratio between MBUS and DRAM. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
generated by cgit v1.1 at 2024-11-09 09:23:37 +0000