summaryrefslogtreecommitdiff
path: root/arch/arm/mach-keystone
Commit message (Collapse)AuthorAgeLines
* ARM: K2G: DDR3: Fix up priv ID for MPUNishanth Menon2016-12-03-4/+19
| | | | | | | | | | | | | | For ECC enabled DDR, we use EDMA to reset all memory values to 0. For K2E/L/H/K the priv ID of 8 was indicative of ARM, but that is not the case for K2G, where it is 1. Unfortunately, ddr3 code had hard coded the privID and had missed identification previously. Fix the same, else unforeseen behavior can be expected in our reset of DDR contents to 0 for ECC enablement. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* keystone2: Move target selection to KconfigAndrew F. Davis2016-11-28-2/+2
| | | | | | | | | The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick a board target, but the header configs also set K2x_EVM. This config is redundant, remove it and use TARGET_K2x_EVM everywhere in its place. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: PLL: Enable glitch free initialization sequenceLokesh Vutla2016-11-13-8/+8
| | | | | | | | | | Update the PLL initialization sequence to avoid glitches while programming. User guide for the same is available at[1]. [1] http://www.ti.com/lit/ug/sprugv2h/sprugv2h.pdf Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone: rename clk_get_rate() to ks_clk_get_rate()Masahiro Yamada2016-10-08-14/+14
| | | | | | | | | | | | | The KeyStone platform has its own clk_get_rate() but its prototype is different from that of the common-clk (clk-uclass) framework. Prefix the KeyStone specific implementation with ks_ in order to avoid name-space conflict. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone: remove declaration of unused functionsMasahiro Yamada2016-10-07-2/+0
| | | | | | | | These two functions are neither defined nor referenced. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Add support for parsing monitor headerLokesh Vutla2016-10-01-4/+18
| | | | | | | | | | | | | | | Given that boot monitor image is being generated to a specific target location depending on the SoC and U-boot relies on addr_mon env variable to be aligned with boot monitor target location. When ever the target address gets updated in boot monitor, it is difficult to sync between u-boot and boot monitor and also there is no way to update user that boot monitor image is updated. To avoid this problem, boot monitor image is being generated with mkimage header. Adding support in mon_install command for parsing this header. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: k2g: Enable ECC byte laneLokesh Vutla2016-10-01-2/+1
| | | | | | | Enable ECC byte lane for k2g-evm Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* treewide: replace #include <asm-generic/errno.h> with <linux/errno.h>Masahiro Yamada2016-09-23-1/+1
| | | | | | | | | | | | | | Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>. Replace all include directives for <asm-generic/errno.h> with <linux/errno.h>. <asm-generic/...> is supposed to be included from <asm/...> when arch-headers fall back into generic implementation. Generally, they should not be directly included from .c files. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> [trini: Add drivers/usb/host/xhci-rockchip.c] Signed-off-by: Tom Rini <trini@konsulko.com>
* keystone: k2h/e/l: Fix DMA coherency for QM PDSPKaricheri, Muralidharan2016-07-25-2/+0
| | | | | | | | | | | | | | commit 1f807a9f32aa ("ARM: keystone2: Refactor MSMC macros to avoid left under a macro KS2_MSMC_SEGMENT_QM_PDSP which is no longer valid. This, in effect disabled DMA coherency for QM PDSP. Given that msmc_k2hkle_common_setup is valid for all K2H/K/L/E SoCs, the #ifdef should been removed in the first place. Do the same. Fixes: 1f807a9f32aa ("ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery") Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: k2g: Configure reset mux to device resetLokesh Vutla2016-06-02-0/+12
| | | | | | | | | | | | | | | | | BOOTCFG_RSTMUX8 register controls the reset mux associated with the ARM. Timer5(dedicated to ARM) when used as WatchDog timer, the events it generates are routed to the above mux. Following are the 3 events that can controlled bt the reset mux: - Device Reset - An interrupt to the ARM_GIC - An interrupt to the ARM_GIC followed by a device reset. Right now to give a default watchdog behaviour "Device reset" is being selected. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Nishanth Menon <nm@ti.com>
* ARM: keystone2: Add missing privilege ID settingsNishanth Menon2016-04-01-1/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add missing Privilege ID settings for KS2 SoCs. Based on: K2H/K: Table 6-7. Privilege ID Settings from SPRS866E (Nov 2013) http://www.ti.com/lit/ds/symlink/66ak2h14.pdf (page 99) K2L: Table 7-7. Privilege ID Settings from SPRS930 (April 2015) http://www.ti.com/lit/ds/symlink/66ak2l06.pdf (page 71) K2E: Table 7-7. Privilege ID Settings from SPRS865D (Mar 2015) http://www.ti.com/lit/ds/symlink/66ak2e05.pdf (page 75) K2G: Table 3-16. PrivIDs from SPRUHY8 (Jan 2016) http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf (page 238) Overall mapping: -------+-----------+-----------+-----------+--------- PrivID | KS2H/K | K2L | K2E | K2G -------+-----------+-----------+-----------+--------- 0 | C66x 0 | C66x 0 | C66x 0 | C66x 0 1 | C66x 1 | C66x 1 | Reserved | ARM 2 | C66x 2 | C66x 2 | Reserved | ICSS0 3 | C66x 3 | C66x 3 | Reserved | ICSS1 4 | C66x 4 | Reserved | Reserved | NETCP 5 | C66x 5 | Reserved | Reserved | CPIE 6 | C66x 6 | Reserved | Reserved | USB 7 | C66x 7 | Reserved | Reserved | Reserved 8 | ARM | ARM | ARM | MLB 9 | NetCP | NetCP | NetCP | PMMC 10 | QM_PDSP | QM_PDSP | QM_PDSP | DSS 11 | PCIe_0 | PCIe_0 | PCIe_0 | MMC 12 | DEBUG/DAP | DEBUG/DAP | DEBUG/DAP | DEBUG/DAP 13 | Reserved | Reserved | PCIe_1 | Reserved 14 | HyperLink | PCIe_1 | HyperLink | Reserved 15 | Reserved | Reserved | TSIP | Reserved -------+-----------+-----------+-----------+--------- NOTE: Few of these might have default configurations, however, since most are software configurable, it is better to explicitly configure the system to have a known default state. Without programming these, we end up seeing lack of coherency on certain peripherals resulting in inexplicable failures (such as USB peripheral's DMA data not appearing on ARM etc and weird workarounds being done by drivers including cache flushes which tend to have system wide performance impact). By marking these segments as shared, we also ensure SoC wide coherency is enabled. Reported-by: Bin Liu <b-liu@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Refactor MSMC macros to avoid #ifdefferyNishanth Menon2016-04-01-23/+53
| | | | | | | | | | | | | | | MSMC segment Privilege ID is not consistent accross the keystone2 SoCs. As the first step to ensure complete SoC wide coherency setup, lets refactor the macros to remove the #if-deffery around the code which obfuscates which IDs are actually enabled for which SoC. As a result of this change the PCIe configuration is moved after the msmc configuration is complete, but that should ideally have no functional impact. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Convert BOOT_SET_BITFIELD into static inline functionNishanth Menon2016-03-27-7/+11
| | | | | | | | | Fix up BOOT_SET_BITFIELD to be a static inline function to be readable with the same functionality. Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Convert BOOT_READ_BITFIELD into static inline functionNishanth Menon2016-03-27-10/+15
| | | | | | | | | BOOT_READ_BITFIELD can easily be a static inline function and be a little more readable with the same functionality. Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Convert BOOTBITMASK to static inline functionNishanth Menon2016-03-27-5/+9
| | | | | | | | | BOOTBITMASK is almost impossible to decode, so convert it into a simpler static line functions of equivalent solution. Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Only link cmd_ddr3.o on non-SPL buildsTom Rini2016-03-16-1/+2
| | | | | | | | | | | | When we switch to including all linker lists in SPL it is important to not include commands as that may lead to link errors due to other things we have already discarded. In this case simply move cmd_ddr3.o over to the list with the rest. Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Switch to using the poweroff commandTom Rini2016-03-16-29/+29
| | | | | | | | | | Now that we have a standard way to power off the hardware, switch to using that rather than our own command. Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Split monitor code / command codeTom Rini2016-03-16-52/+71
| | | | | | | | | | | | When we switch to including all linker lists in SPL it is important to not include commands as that may lead to link errors due to other things we have already discarded. In this case, we split the code for supporting the monitor out from the code for loading it. Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: use detected ddr3a sizeVitaly Andrianov2016-03-14-0/+18
| | | | | | | | | | | | | | | | | | | Because KS2 u-boot works in 32 bit address space the existing ram_size global data field cannot be used. The maximum, which the get_ram_size() can detect is 2GB only. The ft_board_setup() needs the actual ddr3 size to fix up dtb. This commit introduces the ddr3_get_size() which uses SPD data to calculate the ddr3 size. This function replaces the "ddr3_size" environment variable, which was used to get the SODIMM size. For platforms, which don't have SODIMM with SPD and ddr3 is populated to a board a simple ddr3_get_size function that returns ddr3 size has to be implemented. See hardware-k2l.h Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: use SPD info to configure K2HK and K2E DDR3Vitaly Andrianov2016-03-14-0/+463
| | | | | | | | | | | | | | This commit replaces hard-coded EMIF and PHY DDR3 configurations for predefined SODIMMs to a calculated configuration. The SODIMM parameters are read from SODIMM's SPD and used to calculated the configuration. The current commit supports calculation for DDR3 with 1600MHz and 1333MHz only. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: K2G: Add support for different arm/device speedsLokesh Vutla2016-03-14-4/+11
| | | | | | | | | | The maximum device and arm speeds can be determined by reading EFUSE_BOOTROM register. As there is already a framework for reading this register, adding support for all possible speeds on k2g devices. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Allow for board specific speed definitionsLokesh Vutla2016-03-14-8/+8
| | | | | | | | | | Its not compulsory that speed definition should be same on EFUSE_BOOTROM register for all keystone 2 devices. So, allow for board specific speed definitions. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: K2G: power-off DSP during bootSuman Anna2016-03-14-2/+5
| | | | | | | | | | | | | The DSPs are powered on by default upon a Power ON reset, and they are powered off on current Keystone 2 SoCs - K2HK, K2L, K2E during the boot in u-boot. This is not functional on K2G though. Extend the existing DSP power-off support to the only DSP present on K2G. Do note that the PSC clock domain module id for DSP on K2G differs from that of previous Keystone2 SoCs. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Use macro for DSP GEM power domainSuman Anna2016-03-14-1/+2
| | | | | | | | | | Define a macro for the DSP GEM power domain id number and use it instead of a hard-coded number in the code that disables all the DSPs on various Keystone2 SoCs. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: psc: introduce function to hold and release module in reset.Nishanth Menon2016-03-14-0/+108
| | | | | | | | | These are useful for modules that need to be held in reset and are enabled for data to be loaded on to them. Typically these are microcontrollers or other processing entities in the system. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: psc-defs: use adequate () for macrosNishanth Menon2016-03-14-3/+3
| | | | | | | | '#define X a | b' is better defined as '#define X (a | b)' for obvious reasons. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: psc: redo doc in kernel-doc formatNishanth Menon2016-03-14-44/+52
| | | | | | | | | | | u-boot coding style guidance in http://www.denx.de/wiki/U-Boot/CodingStyle clearly mentions that the kernel doc style shall be followed for documentation in u-boot. Current PSC documentation standard does not, so fix that. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: keystone2: Get rid of unused clock filesNishanth Menon2016-03-14-299/+0
| | | | | | | | | | | With commit fe772ebd285b ("ARM: keystone2: Use common definition for clk_get_rate"), we have centralized the clock code into a common clock logic and the redundant files, unfortunately remained... Clean that up. Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: k2g: add SD card and eMMC supportRoger Quadros2015-10-22-0/+22
| | | | | | | | Add MMC support for k2g Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: k2g: update keystone nav rx queue numbersVitaly Andrianov2015-10-22-0/+5
| | | | | | | | update K2G nav rx queue number Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: k2g: Correct base addressesVitaly Andrianov2015-10-22-0/+57
| | | | | | | | Coreect base addresses for SPI, Queue Manager, Ethernet, GPIO, and MSMC segments. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: k2g: Add support for pin mux configurationVitaly Andrianov2015-10-22-0/+58
| | | | | | | Add api for configuring pin mux. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: k2g: Add ddr3 infoVitaly Andrianov2015-10-22-1/+15
| | | | | | | Add ddr3 related info Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: k2g: Add PSC infoVitaly Andrianov2015-10-22-0/+55
| | | | | | | Add psc information for k2g Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: k2g: Add clock informationVitaly Andrianov2015-10-22-2/+10
| | | | | | | | Add clock information for Galileo Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* ARM: k2g: Add pll dataVitaly Andrianov2015-10-22-0/+31
| | | | | | | Add pll data for k2g Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: k2g: Add kconfig supportLokesh Vutla2015-10-22-0/+3
| | | | | | Add Kconfig support Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: k2g: Add support for CPU detectionLokesh Vutla2015-10-22-0/+9
| | | | | | Adding CPU detection support for Keystone2 Galileo. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Use dtb images by defaultLokesh Vutla2015-10-22-2/+2
| | | | | | | Now that OF_CONTROL is enabled on all keystone2 platforms, build the default images with DT. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Fix serial port initLokesh Vutla2015-10-22-0/+2
| | | | | | | | With CONFIG_DM_SERIAL is enabled NS16550_init() cannot be called directly. Driver probe should be taking care of this. So call this function only when DM_SERIAL is not enabled. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: k2e/l: Apply WA for selecting PA clock sourceLokesh Vutla2015-10-17-3/+8
| | | | | | | | | | | | | | | On keystone2 Lamarr and Edison platforms, the PA clocksource mux in PLL REG1, can be changed only after enabling its clock domain. So selecting the output of PASS PLL as input to PA only after enabling the clockdomain. This is as per the debug done by "Vitaly Andrianov <vitalya@ti.com>" and based on the previous work done by "Hao Zhang <hzhang@ti.com>" Fixes: d634a0775bcf ("ARM: keystone2: Cleanup PLL init code") Reported-by: Vitaly Andrianov <vitalya@ti.com> Tested-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* bitops: introduce BIT() definitionHeiko Schocher2015-09-11-4/+0
| | | | | | | | | | | introduce BIT() definition, used in at91_udc gadget driver. Signed-off-by: Heiko Schocher <hs@denx.de> [remove all other occurrences of BIT(x) definition] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
* ARM: k2l: Fix device speedsLokesh Vutla2015-08-28-2/+2
| | | | | | | | | | | ARM supported speeds and init value of core_pll for SDP1200 are programmed wrong as part for the device speed cleanups. Fixing it here. Thanks to "Vitaly Andrianov <vitalya@ti.com>" for bisecting this issue Fixes: c37ed9f11b61 ("ARM: keystone2: Fix dev and arm speed detection") Tested-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Build MLO by defaultLokesh Vutla2015-08-28-0/+4
| | | | | | | | | | | MLO(NAND/MMC boot image), is used for all the ks2 platforms. Enabling it in config.mk so that these images will be automatically built upon calling make. u-boot-spi.gph is already the build target, so not including here. Reported-by: Nishanth Menon <nm@ti.com> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Rename u-boot-nand.gph to MLOLokesh Vutla2015-08-28-2/+4
| | | | | | | | | | | | | | NAND boot mode, ROM expects an image with a gp header in the beginning and an 8bytes filled with zeros at the end. The same is true for SD boot on K2G platforms but the file name should be MLO. Renaming u-boot-nand.gph to MLO, so that same image can be used for NAND and SD boots. And also not including all the u-boot only images under CONFIG_SPL_BUILD. Reported-by: Nishanth Menon <nm@ti.com> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: move the custom build rules out to keystone specific makefileNishanth Menon2015-08-28-0/+22
| | | | | | | | | | | | | | | Keystone has build rules introduced by commit ef509b9063fb7 ("k2hk: add support for k2hk SOC and EVM") and commit 0e7f2dbac6ead ("keystone: add support for NAND gpheader image"). These are not reused by other platforms for the build, hence there is no clear benefit is maintaining them in the generic makefile as a build target. move these to the keystone specific make option Original idea of using config.mk by Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Use common definition for clk_get_rateLokesh Vutla2015-08-12-103/+167
| | | | | | | | Since all the clocks are defined common, and has the same logic to get the frequencies, use a common definition for for clk_get_rate(). Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Remove unsed external clocksLokesh Vutla2015-08-12-50/+13
| | | | | | | | Remove unused external clocks and make a common definition for all keystone platforms. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Cleanup init_pll definitionLokesh Vutla2015-08-12-5/+10
| | | | | | | | | This is just a cosmetic change that makes the calling of pll init code looks much cleaner. Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Use common structure for PLLsLokesh Vutla2015-08-12-51/+22
| | | | | | | | | | Register Base addresses are same for PLLs in all keystone platforms. If a PLL is not available, the corresponding register addresses are marked as reserved. Hence use a common definition. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
generated by cgit v1.1 at 2024-11-01 13:33:52 +0000