summaryrefslogtreecommitdiff
path: root/arch/arm/mach-at91/mpddrc.c
Commit message (Collapse)AuthorAgeLines
* arm: at91/spl: mpddrc: use IP version to check configurationWenyou Yang2016-02-02-7/+11
| | | | | | | | To remove the unnecessary #ifdef-endif, use the mpddrc IP version to check whether or not the interleaved decoding type is supported. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91/spl: mpddrc: add mpddrc DDR3-SDRAM initializationWenyou Yang2016-02-02-0/+89
| | | | | | | | | | | | The DDR3-SDRAM initialization sequence is implemented in accordance with the DDR3-SRAM/DDR3L-SDRAM initialization section described in the SAMA5D2 datasheet. Add registers and definitions of mpddrc controller, which is used to support DDR3 devices. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91/spl: mpddrc: add struct atmel_mpddrc_configWenyou Yang2016-02-02-1/+1
| | | | | | | | | | Add struct atmel_mpddrc_config to accommodate the mpddrc register configurations, not using the mpddrc register map structure, struct atmel_mpddrc, in order to increase readability and reduce run-time memory use. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: at91: mpddr: allow multiple DDR controllersErik van Luijk2015-08-21-19/+22
| | | | | | | | | The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller. This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10). Signed-off-by: Erik van Luijk <evanluijk@interact.nl> [remove 'new blank line at EOF'] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* ARM: atmel: at91sam9n12ek: enable spl supportBo Shen2015-04-01-1/+1
| | | | | | | Enable SPL support for at91sam9n12ek boards, now it supports boot up from NAND flash, serial flash. Signed-off-by: Bo Shen <voice.shen@atmel.com>
* ARM: atmel: at91sam9x5ek: enable spl supportBo Shen2015-04-01-1/+2
| | | | | | | Enable SPL support for at91sam9x5ek board. Now, it supports boot up from NAND flash and SPI flash. Signed-off-by: Bo Shen <voice.shen@atmel.com>
* ARM: at91: collect SoC sources into mach-at91Masahiro Yamada2015-02-21-0/+133
This commit moves source files as follows: arch/arm/cpu/arm920t/at91/* -> arch/arm/mach-at91/arm920t/* arch/arm/cpu/arm926ejs/at91/* -> arch/arm/mach-at91/arm926ejs/* arch/arm/cpu/armv7/at91/* -> arch/arm/mach-at91/armv7/* arch/arm/cpu/at91-common/* -> arch/arm/mach-at91/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.co>