summaryrefslogtreecommitdiff
path: root/arch/arm/lib/crt0.S
Commit message (Collapse)AuthorAgeLines
* arm: Switch 32-bit ARM to using generic global_data setupSimon Glass2015-10-24-24/+4
| | | | | | | | | | There is quite a bit of assembler code that can be removed if we use the generic global_data setup. Less arch-specific code makes it easier to add new features and maintain the start-up code. Drop the unneeded code and adjust the hooks in board_f.c to cope. Signed-off-by: Simon Glass <sjg@chromium.org>
* arm: Correct comments in crt0.S for the recent SPL improvementsSimon Glass2015-09-12-10/+16
| | | | | | | | | | The current comments need a bit of tweaking since we now support stack and global_data relocation in SPL. Also add a reference to the README. For AArch64 this is not implemented, so leave a TODO for this. Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Tim Harvey <tharvey@gateworks.com>
* ARM: Add ARMv7-M supportrev13@wp.pl2015-04-22-0/+30
| | | | Signed-off-by: Kamil Lulko <rev13@wp.pl>
* arm: relocation: clear .bss section with arch memset if definedPrzemyslaw Marczak2015-03-09-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | For ARM architecture, enable the CONFIG_USE_ARCH_MEMSET/MEMCPY, will highly increase the memset/memcpy performance. This is able thanks to the ARM multiple register instructions. Unfortunatelly the relocation is done without the cache enabled, so it takes some time, but zeroing the BSS memory takes much more longer, especially for the configs with big static buffers. A quick test confirms, that the boot time improvement after using the arch memcpy for relocation has no significant meaning. The same test confirms that enable the memset for zeroing BSS, reduces the boot time. So this patch enables the arch memset for zeroing the BSS after the relocation process. For ARM boards, this can be enabled in board configs by defining: 'CONFIG_USE_ARCH_MEMSET'. This was tested on Trats2. A quick test with trace. Boot time from start to main_loop() entry: - ~1384ms - before this change - ~888ms - after this change Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@konsulko.com>
* arm: spl: Allow board_init_r() to run with a larger stackSimon Glass2015-03-04-3/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At present SPL uses a single stack, either CONFIG_SPL_STACK or CONFIG_SYS_INIT_SP_ADDR. Since some SPL features (such as MMC and environment) require a lot of stack, some boards set CONFIG_SPL_STACK to point into SDRAM. They then set up SDRAM very early, before board_init_f(), so that the larger stack can be used. This is an abuse of lowlevel_init(). That function should only be used for essential start-up code which cannot be delayed. An example of a valid use is when only part of the SPL code is visible/executable, and the SoC must be set up so that board_init_f() can be reached. It should not be used for SDRAM init, console init, etc. Add a CONFIG_SPL_STACK_R option, which allows the stack to be moved to a new address before board_init_r() is called in SPL. The expected SPL flow (for CONFIG_SPL_FRAMEWORK) is documented in the README. Signed-off-by: Simon Glass <sjg@chromium.org> For version 1: Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Bo Shen <voice.shen@atmel.com> Acked-by: Bo Shen <voice.shen@atmel.com> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-11-24-0/+5
|\
| * imx: fix exception vectors relocation in imx27Albert ARIBAUD2014-11-20-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 3ff46cc4 fixed exception vectors setting in the general ARM case, by either copying the exception and indirect vector tables to normal (0x00000000) or high (0xFFFF0000) vectors address, or setting VBAR to U-Boot's base if applicable. i.MX27 SoC is ARM926E-JS, thus has only normal and high options, but does not provide RAM at 0xFFFF0000 and has only ROM at 0x00000000; it is therefore not possible to move or change its exception vectors. Besides, i.MX27 ROM code does provide an indirect vectors table but at a non-standard address and with the reset and reserved vectors missing. Turn the current vector relocation code into a weak routine called after relocate_code from crt0, and add strong version for i.MX27. Series-Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de> Tested-by: Philippe Reynes <tremyfr@gmail.com> Tested-by: Philippe Reynes <tremyfr@yahoo.fr>
* | dm: arm: spl: Allow simple malloc() in SPLSimon Glass2014-11-21-1/+1
|/ | | | | | | | For SPL it is sometimes useful to have a simple malloc() just to permit driver model to work, in the cases where the full malloc() is not made available by the board config. Signed-off-by: Simon Glass <sjg@chromium.org>
* arm: Support pre-relocation malloc()Simon Glass2014-08-04-1/+4
| | | | | | Add support for re-relocation malloc() in arm's start-up code. Signed-off-by: Simon Glass <sjg@chromium.org>
* arm: Set up global data before board_init_f()Simon Glass2014-08-04-0/+9
| | | | | | | | | | | | | | | At present arm defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that the global_data pointer is set up in board_init_f(). However it is actually set up before this, it just isn't zeroed. If we zero the global data before calling board_init_f() then we don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA. Make this change (on arm32 only) to simplify the init process. I don't have the ability to test aarch64 yet. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Tom Rini <trini@ti.com>
* arm: use canonical sub mnemonicAndreas Bießmann2014-01-14-1/+1
| | | | | | | | | | | | | | Building some arm boards with older binutils may produce errors like this: ---8<--- crt0.S: Assembler messages: crt0.S:70: Error: register expected, not '#(184)' -- `sub sp,#(184)' --->8--- Use canonical version of the subtract mnemonic to avoid those issues. Reported-by: Alexey Smishlayev <alexey@xtech2.lv> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* ARM: use r9 for gdJeroen Hofstee2013-09-23-8/+8
| | | | | | | | | | | | | | | | To be more EABI compliant and as a preparation for building with clang, use the platform-specific r9 register for gd instead of r8. note: The FIQ is not updated since it is not used in u-boot, and under discussion for the time being. The following checkpatch warning is ignored: WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* cosmetic: arm: fix comments in arch/arm/lib/crt0.SMasahiro Yamada2013-06-10-2/+2
| | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* arm: Remove deprecated and now unused NAND SPLBenoît Thébaudeau2013-04-12-14/+2
| | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* arm: Remove unused relocate_code() parametersBenoît Thébaudeau2013-04-12-5/+3
| | | | | | | | Commit e05e5de7fae5bec79617e113916dac6631251156 made the 2 1st parameters of ARM's relocate_code() useless since it moved the code handling them to crt0.S. So, drop these parameters. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* arm: crt0.S: Remove bogus .globlBenoît Thébaudeau2013-04-12-24/+4
| | | | | | | | | | The purpose of .globl is to export symbols for ld, not to declare external symbols. By the way, use the ENTRY() and ENDPROC() macros to define functions rather than using .global directly. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* Replace __bss_end__ with __bss_endSimon Glass2013-03-15-2/+2
| | | | | | | | | | | | | Note this is a tree-wide change affecting multiple architectures. At present we use __bss_start, but mostly __bss_end__. This seems inconsistent and in a number of places __bss_end is used instead. Change to use __bss_end for the BSS end symbol throughout U-Boot. This makes it possible to use the asm-generic/sections.h file on all archs. Signed-off-by: Simon Glass <sjg@chromium.org>
* arm: move C runtime setup code in crt0.SAlbert ARIBAUD2013-01-08-0/+173
Move all the C runtime setup code from every start.S in arch/arm into arch/arm/lib/crt0.S. This covers the code sequence from setting up the initial stack to calling into board_init_r(). Also, rewrite the C runtime setup and make functions board_init_*() and relocate_code() behave according to normal C semantics (no jumping across the C stack any more, etc). Some SPL targets had to be touched because they use start.S explicitly or for some reason; the relevant maintainers and custodians are cc:ed. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>