summaryrefslogtreecommitdiff
path: root/arch/arm/include
Commit message (Collapse)AuthorAgeLines
* ARM: OMAP5: DDR3: Change io settingsSRICHARAN R2013-11-01-2/+2
| | | | | | | | | | | | | | | | | | | The change from 0x64656465 to 0x64646464 is to remove the weak pull enabled on DQS, nDQS lines. This pulls the differential signals in the same direction which is not intended. So disabling the weak pulls improves signal integrity. On the uEVM there are 4 DDR3 devices. The VREF for 2 of the devices is powered by the OMAP's VREF_CA_OUT pins. The VREF on the other 2 devices is powered by the OMAP's VREF_DQ_OUT pins. So the net effect here is that only half of the DDR3 devices were being supplied a VREF! This was clearly a mistake. The second change improves the robustness of the interface and was specifically seen to cure corruption observed at high temperatures on some boards. With the above two changes better memory stability was observed with extended temperature ranges around 100C. Signed-off-by: Sricharan R <r.sricharan@ti.com>
* dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 buildMinal Shah2013-11-01-0/+1
| | | | | | | | | | | UART booting is supported on this SoC, but via UART3 rather than UART1. Because of this we must change the board to use UART3 for all console access (only one UART is exposed on this board and a slight HW mod is required to switch UARTs). Signed-off-by: Minal Shah <minal.shah@ti.com> [trini: Make apply to mainline, reword commit] Signed-off-by: Tom Rini <trini@ti.com>
* am33xx, davinci: Create and use <asm/davinci_rtc.h>Tom Rini2013-11-01-47/+52
| | | | | | | Create a common header file for the RTC IP block that is shared between davinci and am33xx. Signed-off-by: Tom Rini <trini@ti.com>
* Coding Style cleanup: remove trailing white spaceWolfgang Denk2013-10-14-6/+6
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* ARM: omap4-panda: Add MAC address creation for pandaDan Murphy2013-10-14-0/+4
| | | | | | | | Add a MAC address create based on the OMAP die ID registers. Then poplulate the ethaddr enviroment variable so that the device tree alias can be updated prior to boot. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-10-08-12/+35
|\
| * socfpga: Adding System Manager driverChin Liang See2013-10-07-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adding System Manager driver which will configure the pin mux for real hardware Cyclone V development kit (not Virtual Platform) Signed-off-by: Chin Liang See <clsee@altera.com> Reviewed-by: Pavel Machek <pavel@denx.de> Acked-by: Dinh Nguyen <dinguyen@altera.com> Cc: Wolfgang Denk <wd@denx.de> CC: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
| * ARM: IGEP0033: Update timing to run DDR at 400MHz.Enric Balletbo i Serra2013-10-07-12/+12
| | | | | | | | | | | | | | We can run the DDR at 400MHz, so update the timings for that purpose. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
* | spi: exynos: Support word transfersRajeshwari Shinde2013-10-08-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Since SPI register access is so expensive, it is worth transferring data a word at a time if we can. This complicates the driver unfortunately. Use the byte-swapping feature to avoid having to convert to/from big endian in software. This change increases speed from about 2MB/s to about 4.5MB/s. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* | omap5: add qspi supportMatt Porter2013-10-07-0/+5
| | | | | | | | | | | | | | | | Add QSPI definitions and clock configuration support. Signed-off-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-10-04-1/+51
|\ \ | |/
| * ARM: extend non-secure switch to also go into HYP modeAndre Przywara2013-10-03-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For the KVM and XEN hypervisors to be usable, we need to enter the kernel in HYP mode. Now that we already are in non-secure state, HYP mode switching is within short reach. While doing the non-secure switch, we have to enable the HVC instruction and setup the HYP mode HVBAR (while still secure). The actual switch is done by dropping back from a HYP mode handler without actually leaving HYP mode, so we introduce a new handler routine in our new secure exception vector table. In the assembly switching routine we save and restore the banked LR and SP registers around the hypercall to do the actual HYP mode switch. The C routine first checks whether we are in HYP mode already and also whether the virtualization extensions are available. It also checks whether the HYP mode switch was finally successful. The bootm command part only calls the new function after the non-secure switch. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
| * ARM: add SMP support for non-secure switchAndre Przywara2013-10-03-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the non-secure switch is only done for the boot processor. To enable full SMP support, we have to switch all secondary cores into non-secure state also. So we add an entry point for secondary CPUs coming out of low-power state and make sure we put them into WFI again after having switched to non-secure state. For this we acknowledge and EOI the wake-up IPI, then go into WFI. Once being kicked out of it later, we sanity check that the start address has actually been changed (since another attempt to switch to non-secure would block the core) and jump to the new address. The actual CPU kick is done by sending an inter-processor interrupt via the GIC to all CPU interfaces except the requesting processor. The secondary cores will then setup their respective GIC CPU interface. While this approach is pretty universal across several ARMv7 boards, we make this function weak in case someone needs to tweak this for a specific board. The way of setting the secondary's start address is board specific, but mostly different only in the actual SMP pen address, so we also provide a weak default implementation and just depend on the proper address to be set in the config file. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
| * ARM: add C function to switch to non-secure stateAndre Przywara2013-10-03-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The core specific part of the work is done in the assembly routine in nonsec_virt.S, introduced with the previous patch, but for the full glory we need to setup the GIC distributor interface once for the whole system, which is done in C here. The routine is placed in arch/arm/cpu/armv7 to allow easy access from other ARMv7 boards. We check the availability of the security extensions first. Since we need a safe way to access the GIC, we use the PERIPHBASE registers on Cortex-A15 and A7 CPUs and do some sanity checks. Boards not implementing the CBAR can override this value via a configuration file variable. Then we actually do the GIC enablement: a) enable the GIC distributor, both for non-secure and secure state (GICD_CTLR[1:0] = 11b) b) allow all interrupts to be handled from non-secure state (GICD_IGROUPRn = 0xFFFFFFFF) The core specific GIC setup is then done in the assembly routine. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
| * ARM: add assembly routine to switch to non-secure stateAndre Przywara2013-10-03-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While actually switching to non-secure state is one thing, another part of this process is to make sure that we still have full access to the interrupt controller (GIC). The GIC is fully aware of secure vs. non-secure state, some registers are banked, others may be configured to be accessible from secure state only. To be as generic as possible, we get the GIC memory mapped address based on the PERIPHBASE value in the CBAR register. Since this register is not architecturally defined, we check the MIDR before to be from an A15 or A7. For CPUs not having the CBAR or boards with wrong information herein we allow providing the base address as a configuration variable. Now that we know the GIC address, we: a) allow private interrupts to be delivered to the core (GICD_IGROUPR0 = 0xFFFFFFFF) b) enable the CPU interface (GICC_CTLR[0] = 1) c) set the priority filter to allow non-secure interrupts (GICC_PMR = 0xFF) Also we allow access to all coprocessor interfaces from non-secure state by writing the appropriate bits in the NSACR register. The generic timer base frequency register is only accessible from secure state, so we have to program it now. Actually this should be done from primary firmware before, but some boards seems to omit this, so if needed we do this here with a board specific value. The Versatile Express board does not need this, so we remove the frequency from the configuration file here. After having switched to non-secure state, we also enable the non-secure GIC CPU interface, since this register is banked. Since we need to call this routine also directly from the smp_pen later (where we don't have any stack), we can only use caller saved registers r0-r3 and r12 to not mess with the compiler. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
| * ARM: prepare armv7.h to be included from assembly sourceAndre Przywara2013-10-03-1/+5
| | | | | | | | | | | | | | | | armv7.h contains some useful constants, but also C prototypes. To include it also in assembly files, protect the non-assembly part appropriately. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-10-02-297/+60
|\ \ | |/
| * Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-10-02-7/+31
| |\
| | * i.MX6DQ/DLS: Add pad MX6_PAD_GPIO_1__USB_OTG_IDEric Nelson2013-09-27-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds the pad to i.MX6DQ and changes the i.MX6DLS declaration to match the Linux kernel declaration. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
| | * i.MX6DL/S: add drive-strength back to pads DISP0_DAT2/DAT10Eric Nelson2013-09-20-2/+2
| | | | | | | | | | | | | | | | | | | | | This patch fixes a regression introduced by commit 87d720e0. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
| | * mx6slevk: Add Ethernet supportFabio Estevam2013-09-20-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | mx6slevk has a SMSC8720 connected in RMII mode. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| | * ARM: arch-mx6: fix PLL2_PFD2_FREQMarkus Niebel2013-09-20-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | according to the manual frequency of PLL2 PFD2 is 396.000.000 instead of 400.000.000 Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> Acked-by: Stefano Babic <sbabic@denx.de>
| | * Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic2013-09-13-6/+23
| | |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: MAINTAINERS boards.cfg Signed-off-by: Stefano Babic <sbabic@denx.de>
| | * | mx27: add missing constant for mx27trem2013-09-10-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add some missing constant (chip select, ...) Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr> Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org> Acked-by: Stefano Babic <sbabic@denx.de>
| | * | ARM: mxs: Receive r0 and r1 passed from BootROMMarek Vasut2013-09-10-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make sure value in register r0 and r1 is preserved and passed to the board_init_ll() and mxs_common_spl_init() where it can be processed further. The value in r0 can be configured during the BootStream generation to arbitary value, r1 contains pointer to return value from CALL'd function. This patch also clears the value in r0 before returning to BootROM to make sure the BootROM is not confused by this value. Finally, this patch cleans up some comments in the start.S file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
| * | | Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-10-02-7/+27
| |\ \ \
| | * | | ARM: OMAP5: Avoid writing into LDO SRAM bitsLokesh Vutla2013-09-20-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Writing magic bits into LDO SRAM was suggested only for OMAP5432 ES1.0. Now these are no longer applicable. Moreover these bits should not be overwritten as they are loaded from EFUSE. So avoid writing into these registers. Boot tested on OMAP5432 ES2.0 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| | * | | am335x:Handle worst case scenario for Errata 1.0.24Steve Kipisz2013-09-20-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In Errata 1.0.24, if the board is running at OPP50 and has a warm reset, the boot ROM sets the frequencies for OPP100. This patch attempts to drop the frequencies back to OPP50 as soon as possible in the SPL. Then later the voltages and frequencies up set higher. Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> [trini: Adapt to current framework] Signed-off-by: Tom Rini <trini@ti.com>
| | * | | am335x_evm: am33xx_spl_board_init function and scale core frequencyTom Rini2013-09-20-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a am33xx_spl_board_init (and enable the PMICs) that we may see, depending on the board we are running on. In all cases, we see if we can rely on the efuse_sma register to tell us the maximum speed. In the case of Beaglebone White, we need to make sure we are on AC power, and are on later than rev A1, and then we can ramp up to the PG1.0 maximum of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we need to rely on the efuse_sma if we are on PG2.1, and the defaults for PG1.0/2.0. Signed-off-by: Tom Rini <trini@ti.com>
| | * | | am33xx: Add the efuse_sma CONTROL_MODULE registerTom Rini2013-09-20-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Starting with PG2.1 we have a register in the CONTROL_MODULE that is set with the package type and maximum supported frequency. Add this, and the relevant mask/values. Signed-off-by: Tom Rini <trini@ti.com>
| | * | | am33xx: Add am33xx_spl_board_init function, callTom Rini2013-09-20-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We need to allow for a further call-out in spl_board_init. Call this am33xx_spl_board_init and add a __weak version. This function may be used to scale the MPU frequency up, depending on board needs. Signed-off-by: Tom Rini <trini@ti.com>
| * | | | ARM: use r9 for gdJeroen Hofstee2013-09-23-1/+1
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To be more EABI compliant and as a preparation for building with clang, use the platform-specific r9 register for gd instead of r8. note: The FIQ is not updated since it is not used in u-boot, and under discussion for the time being. The following checkpatch warning is ignored: WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
| * | | ARM: s3c44b0: remove remainders of dead boardMasahiro Yamada2013-09-19-281/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Because commit 5dc5f36 removed B2 board support, arch/arm/cpu/s3c44b0/* and arch/arm/include/asm/arch-s3c44b0/* are not necessary anymore. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Andrea Scian <andrea.scian@dave-tech.it>
| * | | arm: dma_alloc_coherent: malloc() -> memalign()Kuo-Jung Su2013-09-14-1/+1
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Even though the MMU/D-cache is off, some DMA engines still expect strict address alignment. For example, the incoming Faraday FTMAC110 & FTGMAC100 ethernet controllers expect the tx/rx descriptors should always be aligned to 16-bytes boundary. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | | ARM: atmel: add RNDIS gadget supportBo Shen2013-09-24-0/+1
| | | | | | | | | | | | | | | | | | Add RNDIS gadget support to test atmel usba udc driver Signed-off-by: Bo Shen <voice.shen@atmel.com>
* | | ARM: atmel: correct UDPHS nameBo Shen2013-09-24-1/+1
| | | | | | | | | | | | | | | | | | | | | Correct the UDPHS name from UDHPS Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Marek Vasut <marex@denx.de>
* | | USB: gadget: add atmel usba udc driverBo Shen2013-09-24-0/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add atmel usba udc driver support, porting from Linux kernel The original code in Linux Kernel information is as following commit e01ee9f509a927158f670408b41127d4166db1c7 Author: Jingoo Han <jg1.han@samsung.com> Date: Tue Jul 30 17:00:51 2013 +0900 usb: gadget: use dev_get_platdata() Use the wrapper function for retrieving the platform data instead of accessing dev->platform_data directly. Signed-off-by: Bo Shen <voice.shen@atmel.com>
* | | Sound: I2S: Replacing I2S1 with I2S0 channel.Dani Krishna Mohan2013-09-24-0/+6
| | | | | | | | | | | | | | | | | | | | | This patch makes required changes to make use of I2S0 channel instead of I2S1 channel on exynos5250. Signed-off-by: Dani Krishna Mohan <krishna.md@samsung.com>
* | | ARM: Added I2S0 clocks for audioDani Krishna Mohan2013-09-24-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | This patch makes the necessary changes for making use of I2S0 channel instead of I2S1 channel on smdk board. This changes are done to maintain the uniformity to use I2S0 channel. Signed-off-by: Dani Krishna Mohan <krishna.md@samsung.com>
* | | arm: omap5: echi: Add GPL-2.0+ SPDX-License-IdentifierNobuhiro Iwamatsu2013-09-20-14/+1
|/ / | | | | | | Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* | Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2013-09-11-6/+23
|\ \ | |/ |/| | | | | Conflicts: tools/Makefile
| * arm:mmc:goni/exynos: Fix wrong mmc base register devices offset.Przemyslaw Marczak2013-09-11-2/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On s5pc1xx mmc devices offset is multiply of 0x100000, wrong value was 0x10000. Register offset always points to mmc 0 before this change. Add macro definition of mmc dev register offset to s5pc1xx and exynos mmc. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com> Acked-by: Jaehoon Chung <jh80.chung at samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * arm:exynos:gpio: fix s5p_gpio_part_max for exynos4x12Piotr Wilczek2013-08-23-4/+13
| | | | | | | | | | | | | | | | | | This patch fix wrong value returned by 's5p_gpio_part_max' function for Exynos4412. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | socfpga: Creating driver for Reset ManagerChin Liang See2013-09-06-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Consolidating reset code into reset_manager.c. Also separating reset configuration for virtual target and real hardware Cyclone V development kit Signed-off-by: Chin Liang See <clsee@altera.com> Reviewed-by: Pavel Machek <pavel@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
* | Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-09-05-24/+307
|\ \ | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/serial/serial.c The conflict above was a trivial case of adding one init function in each branch, and manually resolved in merge.
| * | i.MX6: Correct ANATOP_PFD (Phase Fractional Divider) register declarationsEric Nelson2013-08-31-23/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some _CLKGATE_MASK and _FRAC_MASK macros were wrong for PFD_480 and the PFD_528 macros were missing. Fortunately, the incorrect macros weren't being used. Since both the PFD_480 and PFD_528 registers have the same structure, and the fields are identical for [0..3] in bytes [0..3], so a single set of macros will suffice. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * | i.MX6: Add convenience macros cpu_type(rev) and is_cpu_type(cpu)Eric Nelson2013-08-31-0/+7
| | | | | | | | | | | | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | imx: add status reporting for HAB statusStefano Babic2013-08-31-1/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add functions to report the HAB (High Assurance Boot) status of e.g. i.MX6 CPUs. This is taken from git://git.freescale.com/imx/uboot-imx.git branch imx_v2009.08_3.0.35_4.0.0 cpu/arm_cortexa8/mx6/generic.c include/asm-arm/arch-mx6/mx6_secure.h Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | ARM: mxs: Added application UART driverAndreas Wass2013-08-21-0/+220
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The driver makes it possible to use an application UART as the U-Boot output console for Freescale i.MX23/i.MX28 devices. Signed-off-by: Andreas Wass <andreas.wass@dalelven.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
* | | Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-09-04-6/+99
|\ \ \
generated by cgit v1.1 at 2024-11-01 05:26:42 +0000