summaryrefslogtreecommitdiff
path: root/arch/arm/include
Commit message (Collapse)AuthorAgeLines
* socfpga: Adding System Manager driverChin Liang See2013-10-07-0/+23
| | | | | | | | | | | | | | | Adding System Manager driver which will configure the pin mux for real hardware Cyclone V development kit (not Virtual Platform) Signed-off-by: Chin Liang See <clsee@altera.com> Reviewed-by: Pavel Machek <pavel@denx.de> Acked-by: Dinh Nguyen <dinguyen@altera.com> Cc: Wolfgang Denk <wd@denx.de> CC: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
* ARM: IGEP0033: Update timing to run DDR at 400MHz.Enric Balletbo i Serra2013-10-07-12/+12
| | | | | | | We can run the DDR at 400MHz, so update the timings for that purpose. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
* ARM: extend non-secure switch to also go into HYP modeAndre Przywara2013-10-03-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | For the KVM and XEN hypervisors to be usable, we need to enter the kernel in HYP mode. Now that we already are in non-secure state, HYP mode switching is within short reach. While doing the non-secure switch, we have to enable the HVC instruction and setup the HYP mode HVBAR (while still secure). The actual switch is done by dropping back from a HYP mode handler without actually leaving HYP mode, so we introduce a new handler routine in our new secure exception vector table. In the assembly switching routine we save and restore the banked LR and SP registers around the hypercall to do the actual HYP mode switch. The C routine first checks whether we are in HYP mode already and also whether the virtualization extensions are available. It also checks whether the HYP mode switch was finally successful. The bootm command part only calls the new function after the non-secure switch. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
* ARM: add SMP support for non-secure switchAndre Przywara2013-10-03-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the non-secure switch is only done for the boot processor. To enable full SMP support, we have to switch all secondary cores into non-secure state also. So we add an entry point for secondary CPUs coming out of low-power state and make sure we put them into WFI again after having switched to non-secure state. For this we acknowledge and EOI the wake-up IPI, then go into WFI. Once being kicked out of it later, we sanity check that the start address has actually been changed (since another attempt to switch to non-secure would block the core) and jump to the new address. The actual CPU kick is done by sending an inter-processor interrupt via the GIC to all CPU interfaces except the requesting processor. The secondary cores will then setup their respective GIC CPU interface. While this approach is pretty universal across several ARMv7 boards, we make this function weak in case someone needs to tweak this for a specific board. The way of setting the secondary's start address is board specific, but mostly different only in the actual SMP pen address, so we also provide a weak default implementation and just depend on the proper address to be set in the config file. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
* ARM: add C function to switch to non-secure stateAndre Przywara2013-10-03-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | The core specific part of the work is done in the assembly routine in nonsec_virt.S, introduced with the previous patch, but for the full glory we need to setup the GIC distributor interface once for the whole system, which is done in C here. The routine is placed in arch/arm/cpu/armv7 to allow easy access from other ARMv7 boards. We check the availability of the security extensions first. Since we need a safe way to access the GIC, we use the PERIPHBASE registers on Cortex-A15 and A7 CPUs and do some sanity checks. Boards not implementing the CBAR can override this value via a configuration file variable. Then we actually do the GIC enablement: a) enable the GIC distributor, both for non-secure and secure state (GICD_CTLR[1:0] = 11b) b) allow all interrupts to be handled from non-secure state (GICD_IGROUPRn = 0xFFFFFFFF) The core specific GIC setup is then done in the assembly routine. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
* ARM: add assembly routine to switch to non-secure stateAndre Przywara2013-10-03-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While actually switching to non-secure state is one thing, another part of this process is to make sure that we still have full access to the interrupt controller (GIC). The GIC is fully aware of secure vs. non-secure state, some registers are banked, others may be configured to be accessible from secure state only. To be as generic as possible, we get the GIC memory mapped address based on the PERIPHBASE value in the CBAR register. Since this register is not architecturally defined, we check the MIDR before to be from an A15 or A7. For CPUs not having the CBAR or boards with wrong information herein we allow providing the base address as a configuration variable. Now that we know the GIC address, we: a) allow private interrupts to be delivered to the core (GICD_IGROUPR0 = 0xFFFFFFFF) b) enable the CPU interface (GICC_CTLR[0] = 1) c) set the priority filter to allow non-secure interrupts (GICC_PMR = 0xFF) Also we allow access to all coprocessor interfaces from non-secure state by writing the appropriate bits in the NSACR register. The generic timer base frequency register is only accessible from secure state, so we have to program it now. Actually this should be done from primary firmware before, but some boards seems to omit this, so if needed we do this here with a board specific value. The Versatile Express board does not need this, so we remove the frequency from the configuration file here. After having switched to non-secure state, we also enable the non-secure GIC CPU interface, since this register is banked. Since we need to call this routine also directly from the smp_pen later (where we don't have any stack), we can only use caller saved registers r0-r3 and r12 to not mess with the compiler. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
* ARM: prepare armv7.h to be included from assembly sourceAndre Przywara2013-10-03-1/+5
| | | | | | | | armv7.h contains some useful constants, but also C prototypes. To include it also in assembly files, protect the non-assembly part appropriately. Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
* Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-10-02-7/+31
|\
| * i.MX6DQ/DLS: Add pad MX6_PAD_GPIO_1__USB_OTG_IDEric Nelson2013-09-27-1/+2
| | | | | | | | | | | | | | | | This patch adds the pad to i.MX6DQ and changes the i.MX6DLS declaration to match the Linux kernel declaration. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
| * i.MX6DL/S: add drive-strength back to pads DISP0_DAT2/DAT10Eric Nelson2013-09-20-2/+2
| | | | | | | | | | | | | | This patch fixes a regression introduced by commit 87d720e0. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
| * mx6slevk: Add Ethernet supportFabio Estevam2013-09-20-0/+18
| | | | | | | | | | | | | | | | mx6slevk has a SMSC8720 connected in RMII mode. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * ARM: arch-mx6: fix PLL2_PFD2_FREQMarkus Niebel2013-09-20-1/+1
| | | | | | | | | | | | | | | | according to the manual frequency of PLL2 PFD2 is 396.000.000 instead of 400.000.000 Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> Acked-by: Stefano Babic <sbabic@denx.de>
| * Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic2013-09-13-6/+23
| |\ | | | | | | | | | | | | | | | | | | | | | Conflicts: MAINTAINERS boards.cfg Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | mx27: add missing constant for mx27trem2013-09-10-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | Add some missing constant (chip select, ...) Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr> Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org> Acked-by: Stefano Babic <sbabic@denx.de>
| * | ARM: mxs: Receive r0 and r1 passed from BootROMMarek Vasut2013-09-10-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make sure value in register r0 and r1 is preserved and passed to the board_init_ll() and mxs_common_spl_init() where it can be processed further. The value in r0 can be configured during the BootStream generation to arbitary value, r1 contains pointer to return value from CALL'd function. This patch also clears the value in r0 before returning to BootROM to make sure the BootROM is not confused by this value. Finally, this patch cleans up some comments in the start.S file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* | | Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-10-02-7/+27
|\ \ \
| * | | ARM: OMAP5: Avoid writing into LDO SRAM bitsLokesh Vutla2013-09-20-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Writing magic bits into LDO SRAM was suggested only for OMAP5432 ES1.0. Now these are no longer applicable. Moreover these bits should not be overwritten as they are loaded from EFUSE. So avoid writing into these registers. Boot tested on OMAP5432 ES2.0 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * | | am335x:Handle worst case scenario for Errata 1.0.24Steve Kipisz2013-09-20-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In Errata 1.0.24, if the board is running at OPP50 and has a warm reset, the boot ROM sets the frequencies for OPP100. This patch attempts to drop the frequencies back to OPP50 as soon as possible in the SPL. Then later the voltages and frequencies up set higher. Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> [trini: Adapt to current framework] Signed-off-by: Tom Rini <trini@ti.com>
| * | | am335x_evm: am33xx_spl_board_init function and scale core frequencyTom Rini2013-09-20-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a am33xx_spl_board_init (and enable the PMICs) that we may see, depending on the board we are running on. In all cases, we see if we can rely on the efuse_sma register to tell us the maximum speed. In the case of Beaglebone White, we need to make sure we are on AC power, and are on later than rev A1, and then we can ramp up to the PG1.0 maximum of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we need to rely on the efuse_sma if we are on PG2.1, and the defaults for PG1.0/2.0. Signed-off-by: Tom Rini <trini@ti.com>
| * | | am33xx: Add the efuse_sma CONTROL_MODULE registerTom Rini2013-09-20-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Starting with PG2.1 we have a register in the CONTROL_MODULE that is set with the package type and maximum supported frequency. Add this, and the relevant mask/values. Signed-off-by: Tom Rini <trini@ti.com>
| * | | am33xx: Add am33xx_spl_board_init function, callTom Rini2013-09-20-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We need to allow for a further call-out in spl_board_init. Call this am33xx_spl_board_init and add a __weak version. This function may be used to scale the MPU frequency up, depending on board needs. Signed-off-by: Tom Rini <trini@ti.com>
* | | | ARM: use r9 for gdJeroen Hofstee2013-09-23-1/+1
|/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To be more EABI compliant and as a preparation for building with clang, use the platform-specific r9 register for gd instead of r8. note: The FIQ is not updated since it is not used in u-boot, and under discussion for the time being. The following checkpatch warning is ignored: WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | | ARM: s3c44b0: remove remainders of dead boardMasahiro Yamada2013-09-19-281/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Because commit 5dc5f36 removed B2 board support, arch/arm/cpu/s3c44b0/* and arch/arm/include/asm/arch-s3c44b0/* are not necessary anymore. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Andrea Scian <andrea.scian@dave-tech.it>
* | | arm: dma_alloc_coherent: malloc() -> memalign()Kuo-Jung Su2013-09-14-1/+1
| |/ |/| | | | | | | | | | | | | | | | | | | | | Even though the MMU/D-cache is off, some DMA engines still expect strict address alignment. For example, the incoming Faraday FTMAC110 & FTGMAC100 ethernet controllers expect the tx/rx descriptors should always be aligned to 16-bytes boundary. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2013-09-11-6/+23
|\ \ | |/ |/| | | | | Conflicts: tools/Makefile
| * arm:mmc:goni/exynos: Fix wrong mmc base register devices offset.Przemyslaw Marczak2013-09-11-2/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On s5pc1xx mmc devices offset is multiply of 0x100000, wrong value was 0x10000. Register offset always points to mmc 0 before this change. Add macro definition of mmc dev register offset to s5pc1xx and exynos mmc. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com> Acked-by: Jaehoon Chung <jh80.chung at samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * arm:exynos:gpio: fix s5p_gpio_part_max for exynos4x12Piotr Wilczek2013-08-23-4/+13
| | | | | | | | | | | | | | | | | | This patch fix wrong value returned by 's5p_gpio_part_max' function for Exynos4412. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | socfpga: Creating driver for Reset ManagerChin Liang See2013-09-06-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Consolidating reset code into reset_manager.c. Also separating reset configuration for virtual target and real hardware Cyclone V development kit Signed-off-by: Chin Liang See <clsee@altera.com> Reviewed-by: Pavel Machek <pavel@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
* | Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-09-05-24/+307
|\ \ | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/serial/serial.c The conflict above was a trivial case of adding one init function in each branch, and manually resolved in merge.
| * | i.MX6: Correct ANATOP_PFD (Phase Fractional Divider) register declarationsEric Nelson2013-08-31-23/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some _CLKGATE_MASK and _FRAC_MASK macros were wrong for PFD_480 and the PFD_528 macros were missing. Fortunately, the incorrect macros weren't being used. Since both the PFD_480 and PFD_528 registers have the same structure, and the fields are identical for [0..3] in bytes [0..3], so a single set of macros will suffice. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
| * | i.MX6: Add convenience macros cpu_type(rev) and is_cpu_type(cpu)Eric Nelson2013-08-31-0/+7
| | | | | | | | | | | | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | imx: add status reporting for HAB statusStefano Babic2013-08-31-1/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add functions to report the HAB (High Assurance Boot) status of e.g. i.MX6 CPUs. This is taken from git://git.freescale.com/imx/uboot-imx.git branch imx_v2009.08_3.0.35_4.0.0 cpu/arm_cortexa8/mx6/generic.c include/asm-arm/arch-mx6/mx6_secure.h Signed-off-by: Stefano Babic <sbabic@denx.de>
| * | ARM: mxs: Added application UART driverAndreas Wass2013-08-21-0/+220
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The driver makes it possible to use an application UART as the U-Boot output console for Freescale i.MX23/i.MX28 devices. Signed-off-by: Andreas Wass <andreas.wass@dalelven.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
* | | Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-09-04-6/+99
|\ \ \
| * | | arm, am335x: add watchdog supportHeiko Schocher2013-08-28-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add TI OMAP 16xx & 24xx/34xx 32KHz (non-secure) watchdog support. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
| * | | arm, am335x: add some missing registers and defines for lcd and epwm supportHeiko Schocher2013-08-28-1/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - add missing register defines in struct cm_perpl epwmss0clkctrl epwmss2clkctrl lcdcclkstctrl - add missing register defines in struct cm_dpll clklcdcpixelclk - add struct pwmss_regs - add struct pwmss_ecap_regs - add LCD Controller base LCD_CNTL_BASE - add PWM0 controller base PWMSS0_BASE Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
| * | | arm, am33xx: add defines for gmii_sel_register bitsHeiko Schocher2013-08-28-0/+19
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
| * | | omap5: Expand CONFIG_SPL_MAX_SIZE and comment upon SRAM_SCRATCH_SPACE_ADDRTom Rini2013-08-28-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After examining both TRMs and doing some experimentation, we can rely on using the start of the download area for CONFIG_SPL_TEXT_BASE and then move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for peripheral boot modes such as UART. Signed-off-by: Tom Rini <trini@ti.com>
| * | | am33xx: Correct and expand comments on CONFIG_SPL_MAX_SIZETom Rini2013-08-28-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We had been allowing the max size to be larger than actually allowed by the ROM. Expand the commentary here to explain why we set these locations. Signed-off-by: Tom Rini <trini@ti.com>
| * | | arm: omap3: fix SRAM copy and execution sequenceAlbert ARIBAUD2013-08-28-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix size calculation in copy of go_to_speed into SRAM. Use SRAM_CLK_CODE in call to SRAM-based go_to_speed. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
| * | | ARM: OMAP4470: Add voltage and dpll dataTaras Kondratiuk2013-08-28-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OMAP4470 reference design uses TWL6032 PMIC with a following connection scheme: VDD_CORE = TWL6032 SMPS2 VDD_MPU = TWL6032 SMPS1 VDD_IVA = TWL6032 SMPS5 Set voltage and frequency values according to OMAP4470 Data Manual Operating Condition Addendum v0.7 Signed-off-by: Taras Kondratiuk <taras@ti.com>
| * | | ARM: OMAP4470: Add OMAP4470 identificationTaras Kondratiuk2013-08-28-0/+2
| | |/ | |/| | | | | | | Signed-off-by: Taras Kondratiuk <taras@ti.com>
* | | Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD2013-09-04-3/+8
|\ \ \
| * | | arm: sama5d3: fix smc cs related registers offsetBo Shen2013-08-22-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | the smc cs related registers start at 0x600 and loop with 5 registers so the reserved register should be in at91_smc structure while no in at91_cs structure. So fix it Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | | ARM: at91: sama5d3: remove unused definition about PMECC alpha table offsetWu, Josh2013-08-22-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | | ARM: at91: atmel_nand: pmecc driver will select the galois table by sector sizeWu, Josh2013-08-22-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Define the galois index table offset in chip head file. So user do not need to set by himself. Driver will set it correctly according to sector_size. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> [rebased on master] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | | arm: atmel: add gmac support for sama5d3xek boardBo Shen2013-08-22-0/+1
| |/ / | | | | | | | | | | | | | | | | | | | | | add gmac support for sama5d3xek board, the gmac embedded in: - sama5d33, sama5d34, sama5d35 Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* | | Merge 'u-boot-microblaze/zynq' into (u-boot-arm/master'Albert ARIBAUD2013-09-03-0/+9
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/include/asm/arch-zynq/hardware.h The conflict above was trivial and solved during merge.
| * | | zynq: Add new ddrc driver for ECC supportMichal Simek2013-08-12-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The first 1MB is not initialized by first stage bootloader. Check if memory is setup to 16bit mode and ECC is enabled. If it is, clear the first 1MB. Also u-boot should report only the half size of memory. Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | | | usb: ehci-mx5: Use 'bool' instead of 'unsigned char'Fabio Estevam2013-08-26-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The 'enable' argument can be better expressed as boolean. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
generated by cgit v1.1 at 2024-09-19 19:44:42 +0000