| Commit message (Collapse) | Author | Age | Lines |
... | |
| |/
| |
| |
| |
| |
| |
| |
| |
| | |
The Kona architecture is present on a number of Broadcom mobile SoCs
including the bcm281xx family of chips.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
|
|\ \ |
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add QSPI definitions and clock configuration support.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The dual lite and solo variant have only 4 SPI controller.
respect this in the MXC_SPI_BASE_ADRESSES macro
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Provide define for the SCLK_CTL field of the config reg of ECSPI.
While at it, oder the defines to improve readability and make
adding more defines easier.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|\ \ \
| | |/
| |/| |
|
| |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Conflicts:
Makefile
drivers/net/npe/Makefile
These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
|
| |\ \ \ |
|
| | | | |
| | | | |
| | | | |
| | | | | |
Signed-off-by: Andy Ng <andreas2025@gmail.com>
|
| | |\ \ \ |
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Add L2 cache support and enable it by default.
Configure the L2 cache in the same way as done by FSL kernel:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_4.1.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Currently when we boot a mx6dual U-boot reports that it is a mx6quad.
Report it as MX6D instead:
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Instead of duplicating the CPU definitions at mx5 and mx6 sys_proto.h header
files, introduce a common header to centralize such definitions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Add PCIe driver for the Freescale i.MX6 SoC . This driver operates the
PCIe block in RC mode only, the EP mode is NOT supported. The driver is
tested with the Intel e1000 NIC driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Split the SATA clock enabling function and add PCI express clock
enabling function. The SATA clock enabling function starts up the
100MHz SATA reference PLL in ENET_PLL register, but the code can
be re-used to enable the 125MHz PCIe reference in ENET_PLL, so pull
this code into separate function. Moreover, add the PCIe clock
enabling code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
| | |\ \ \ \ |
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.
BSS section is moved to SDRAM because fat support
requires more space than SRAM size.
Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Define both serial uarts in the driver and return
default uart based on board configuration.
- Move baseaddresses to hardware.h
- Define default baudrate and clock values
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
These numbers will be reused by SPL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| |\ \ \ \ \ \ |
|
| | | |_|/ / /
| | |/| | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The architecture is unmaintained and dead, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
|
| |_|_|_|/ /
|/| | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Having CONFIG_SYS_I2C_BASE requires DW I2C driver to explicitly include
<arch/hardware.h> which other platforms may not have at all.
It's always good to have a driver platform-independent.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
- When CONFIG_DISPLAY_CPUINFO is not enabled,
print_cpuinfo() should be defined as an empty function
in a header, include/common.h
- Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
from caller, common/board_f.c and arch/arm/lib/board.c
- Remove redundant prototypes in arch/arm/lib/board.c,
arch/arm/include/asm/arch-am33x/sys_proto.h and
board/nokia/rx51/rx51.h, keeping the one in include/common.h
- Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
where it is missing
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|/ / / / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add the SATA boot support for OMAP5 and dra7xx.
Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.
Added the ROM boot device ID for SATA.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
|\ \ \ \ \ |
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Typo: The correct value is 1 not 2.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
|
| |\ \ \ \ \ |
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This patch adds s5p_cpu_rev.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This patch enables to read cpu revision on Exynos CPU.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The value of PERIPH_ID_COUNT was wrong, and unnecessary.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Rajehswari Shinde <rajeshwari.s@samsung.com>
|
| | |/ / / /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Old s5p gpio coding method was not clean and was not working properly
for all parts and banks. New method is clean and easy to extend.
Gpio coding mask:
0x000000ff - pin number
0x00ffff00 - bank offset
0xff000000 - part number
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
These headers define the Tegra124 hardware. Add them to the usual
place.
Add Tegra124 chip ID/SKU ID definitions to common headers.
There's no real HW change on Tegra124 for 90% of the toys, so it might
make sense for a future patch to unify some of the content of these
files in a common location.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Pass just the partition ID to power_partition(), rather than also passing
the partition's status register mask too. This makes it simpler to get
call-sites correct, since they don't need to pass two different values
that define the same thing and must match.
Consequently, we can remove the mask definitions from pmc.h.
Suggested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Use a named constant for the PLL lock bit in enable_cpu_clocks().
Construct the complete value of pmc_pwrgate_toggle, rather than doing a
read-modify-write; the register is simple enough and doesn't need to
maintain state between operations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Based on the Tegra TRM, the system clock (which is the AVP clock) can
run up to 275MHz. On power on, the default sytem clock source is set to
PLLP_OUT0. In function clock_early_init(), PLLP_OUT0 will be set to
408MHz which is beyond system clock's upper limit.
The fix is to set the system clock to CLK_M before initializing PLLP,
and then switch back to PLLP_OUT4, which has an appropriate divider
configured, after PLLP has been configured
Implement this logic in new function tegra30_set_up_pllp(),
which sets up PLLP and all PLLP_OUT* dividers, and handles the AVP
clock switching. Remove the duplicate PLLP setup from pllx_set_rate()
and adjust_pllp_out_freqs().
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
[swarren, significantly refactored the change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Tegra114 and later's PMC module removes the pwrgate_timer_on register
and replaces it with a clamp_status register. Adjust pmc.h to reflect
this, and update any code affected by the change.
The cpu.c change in this patch was extracted from a much larger patch
by Jimmy Zhang. The pmc.h change was written from scratch, but inspired
by related changes made by Tom Warren.
There could well be other differences in the PMC register set for chips
after Tegra20/30. However, they don't affect the code in U-Boot at
present, so I haven't attempted an exhaustive update of pmc.h.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Some clock sources have 3-bit muxes in bits 31:29. Implement core
support for this mux field.
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Since all code that sets or interprets MASK_BITS_* now uses the enums
to define/compare the values, there is no need for MASK_BITS_* to have
a specific integer value. In fact, having a specific integer value may
encourage people to hard-code those values, or interpret the values in
incorrect ways.
As such, remove the logic that assigns a specific value to the enum
values in order to make it completely clear that it's just an enum, not
something that directly represents some integer value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
OUT_CLK_SOURCE_ are currently named after the number of bits the mask
they represent includes. However, bit count is not the only possible
variable; bit position may also vary. Rename OUT_CLK_SOURCE_ to
OUT_CLK_SOURCE_31_30_ and OUT_CLK_SOURCE4_ to OUT_CLK_SOURCE_31_28 to
more completely describe exactly what they represent, without having to
go look up the definitions.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The only place where the MASK_BITS_* values are used is in
adjust_periph_pll(), which interprets the value 4 (old MASK_BITS_29_28,
new MASK_BITS_31_28) as being associated with mask OUT_CLK_SOURCE4_MASK,
i.e. bits 31:28. Rename the MASK_BITS_ macro to reflect how it's actually
implemented.
Note that no Tegra clock register actually uses all of bits 31:28 as
the mux field. Rather, bits 30:28, 29:28, or 28 are used. However, in
those cases, nothing is stored in the bits above the mux field, so it's
safe to pretend that the mux field extends all the way to the end of the
register. As such, the U-Boot clock driver is currently a bit lazy, and
doesn't distinguish between 31:28, 30:28, 29:28 and 28; it just lumps
them all together and pretends they're all 31:28. This patch doesn't
cause this issue; it was pre-existing. Hopefully, future patches will
clean this up.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |/ / / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The enum used to define the set of register bits used to represent a
clock's input mux, MUX_BITS_*, is defined separately for each SoC at
present. Move this definition to a common location to ease fixing up
some issues with the definition, and the code that uses it.
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |\ \ \ \
| | |_|_|/
| |/| | | |
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Patch adds modification to shared omap5 abb_setup() function, and
proper registers definitions needed for ABB setup sequence. ABB is
initialized for MPU voltage domain at OPP_NOM.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support
for ES1.1 IDCODE change.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This patch enables dynamically powering down the
IO receiver when not performing a read on boards using DDR3.
This optimizes both active and standby power consumption.
This bit is not set on EVM SK and EVM 1.5 and later boards.
Setting the same.
This has been tested on PG2.0 EVM1.5, EVM1.2, EVM-SK, BBB.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Other TI processors like am33xx, omap4 and omap5 have called these variables
as NON_SECURE_SRAM_*, shouldn't be a big problem rename these variables to
be coherent.
One reason more to rename these variables is to have the possibility of any
OMAP3 board to use the ti_armv7_common.h include as the NON_SECURE_SRAM_END
is used to define the CONFIG_SYS_INIT_SP_ADDR variable.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
|