summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/imx-common/iomux-v3.h
Commit message (Collapse)AuthorAgeLines
* MLK-10812-3 imx:mx6ul PAD_CTL_SPEED_LOW for mx6ulPeng Fan2015-05-05-1/+1
| | | | | | PAD_CTL_SPEED_LOW for mx6ul same with mx6sx. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10566: arm :imx7d: fix iomuxc-lpsr daisy chain settingsAdrian Alonso2015-04-29-0/+1
| | | | | | | | | | | | | | | * For IOMUXC LPSR pads when daisy chain register needs to be set the result offsets for sel_input register is incorrect as base address is 0x302C0000 and the passed offset does not resolve to the intended input sel pad register; input sel base offset should start in 0x30330000. * Add an addiotional fixed offset of 0x70000 to address the input sel offset: INPUT_SEL = 0x302C0000 + 0x70000 + sel_input_ofs. Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 5d4612613eb2e85f1929d8cf5cb6aac6ba9e5fd7)
* MLK-10176-2 imx: mx7: Update IOMUX settings and definitionsYe.Li2015-04-29-0/+31
| | | | | | | | Add mx7d pins for various IOMUX settins. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 25f508ff6891d8861e1fe49c4e2f840cff0040e0) Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-14 imx:mx6sx fix pad settingsPeng Fan2015-04-29-1/+5
| | | | | | Fix PAD_CTL_SPEED_LOW pad settings. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* imx: mx6 sabreauto: Add board support for USB EHCIYe.Li2014-11-03-0/+5
| | | | | | | | | | | | | | | | | | On mx6 sabreauto board, there are two USB ports: 0: OTG 1: HOST The EHCI driver is enabled for this board, but the IOMUX and VBUS power control is not implemented, which cause both USB port failed to work. This patch fix the problem by adding the board support codes. Since the power control uses the GPIO pin from port expander MAX7310, the PCA953X driver is enabled for accessing the MAX7310. The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting its daisy chain. Add a new function "imx_iomux_set_gpr_register" to handle GPR register setting. Signed-off-by: Ye.Li <B37916@freescale.com>
* vf610twr: Tune DDR initialization settingsAnthony Felice2014-10-07-0/+2
| | | | | | | | | | | | | | | Removed settings in unsupported register fields. They didn’t do anything, and in most cases, were not documented in the reference manual. Changed register settings to comply with JEDEC required values. Changed timing parameters because they included full clock periods that were doing nothing. Signed-off-by: Anthony Felice <tony.felice@timesys.com> [rebased on v2014.10-rc2] Signed-off-by: Stefan Agner <stefan@agner.ch>
* arm: vf610: add NFC pin muxStefan Agner2014-08-30-0/+4
| | | | | | | | Add pin mux for NAND Flash Controller (NFC). NAND can be connected using 8 or 16 data lines, this patch adds pin mux entries for all 16 data lines. Signed-off-by: Stefan Agner <stefan@agner.ch>
* Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2014-06-30-0/+25
|\
| * imx: iomux: add macros to setup iomux for multiple SoC typesTim Harvey2014-06-06-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allow imx_iomux_v3_setup_multiple_pads to take a multi-cpu pad_list and add macros for declaring the pad_list that take into account the SoC types supported using CONFIG_MX6QDL (supports both the MX6Q and MX6DL iomux). Cc: Stefan Roese <sr@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Andy Ng <andreas2025@gmail.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Tapani Utriainen <tapani@technexion.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* | arm: imx: Add two macros for VF610 in IOMUX_PAD structureAlison Wang2014-06-09-0/+2
|/ | | | | | | Add PAD_CTL_DSE_150ohm and PAD_CTL_PUS_22K_UP for VF610 in IOMUX_PAD structure. Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
* iomux-v3: Add support for mx6sl LVE bitFabio Estevam2014-05-09-0/+5
| | | | | | | | | | | | | On mx6sl there is a LVE (Low Voltage Enable) bit in the IOMUXC_SW_PAD_CTL register that can enable or disable low voltage on the pad. LVE is bit 22 of IOMUXC_SW_PAD_CTL register, but in order to make the calculation easier we can define it as a flag in bit 1, since this bit is unused. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Otavio Salvador <otavio@ossystems.com.br>
* imx: Easy enabling of SION per-pin using MUX_MODE_SION helper macroOtavio Salvador2014-01-03-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The macro allows easy setting in per-pin, as for example: ,---- | imx_iomux_v3_setup_pad(MX6_PAD_NANDF_D1__GPIO_2_1 | MUX_MODE_SION); `---- The IOMUX_CONFIG_SION allows for reading PAD value from PSR register. The following quote from the datasheet: ,---- | ... | 28.4.2.2 GPIO Write Mode | The programming sequence for driving output signals should be as follows: | 1. Configure IOMUX to select GPIO mode (Via IOMUXC), also enable SION if need | to read loopback pad value through PSR | 2. Configure GPIO direction register to output (GPIO_GDIR[GDIR] set to 1b). | 3. Write value to data register (GPIO_DR). | ... `---- This fixes the gpio_get_value to properly work when a GPIO is set for output and has no conflicts. Thanks for Benoît Thébaudeau <benoit.thebaudeau@advansee.com>, Fabio Estevam <fabio.estevam@freescale.com> and Eric Bénard <eric@eukrea.com> for helping to properly trace this down. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-13/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* arm: vf610: Add IOMUX support for Vybrid VF610Alison Wang2013-06-03-0/+18
| | | | | | | | | | | | | This patch adds the IOMUX support for Vybrid VF610 platform. There is a little difference for IOMUXC module between VF610 and i.MX platform, the muxmode and pad configuration share one 32bit register on VF610, but they are two independent registers on I.MX platform. A CONFIG_IOMUX_SHARE_CONFIG_REG was introduced to fit this difference. Signed-off-by: Alison Wang <b18965@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: iomux-v3: Include PKE and PUE to pad control pull definitionsBenoît Thébaudeau2013-04-28-5/+5
| | | | | | | | | | | | | | | | | PUE requires PKE to mean something, as do pull values with PUE, so do not compell users to explicitly use PKE and PUE everywhere. This is also what is done on Linux and what has already been done for i.MX51. By the way, remove some unused pad control definitions. There is no change of behavior. Note that SPI_PAD_CTRL was defined by several boards with a pull value, but without PKE or PUE, which means that no pull was actually enabled in the pad. This might be a bug in those boards, but this patch does not change the behavior, so it just removes the meaningless pull value from those definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: iomux-v3: Restore Linux's NEW_PAD_CTRL() macroBenoît Thébaudeau2013-04-28-0/+3
| | | | | | This macro will be useful for future changes. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: iomux-v3: cosmetic: Reorganize definitionsBenoît Thébaudeau2013-04-28-14/+19
| | | | | | | Keep pad control definitions together, and organize definitions in a more legible way. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: iomux-v3: Fix common pad control definitionsBenoît Thébaudeau2013-04-28-0/+28
| | | | | | | | | | | | | Commit dc88403 "iomux-v3: Place pad control definitions into common file" broke mx51_efikamx because it made i.MX6's pad control definitions conflict with i.MX51's. i.MX51's pad control definitions are actually common to some other i.MX (25/35/53), so move them to the common iomux-v3.h (just like what is done in Linux's), and select the correct definitions depending on whether CONFIG_MX6 is defined or not. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* iomux-v3: Place pad control definitions into common fileFabio Estevam2013-04-22-1/+26
| | | | | | | Instead of having the same PAD control definition in each MX6 variant pin file, place it into a common location. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* arm: imx: Change iomux functions to void typeStefan Roese2013-04-16-2/+2
| | | | | | | | They never return anything also than 0, so lets change the function to void instead. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
* i.MX: iomux: input pad array can be constEric Nelson2012-10-16-1/+2
| | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Stefano Babic <sbabic@denx.de>
* iomux: move IOMUX_GPR13_xxx definesTroy Kisky2012-09-01-111/+0
| | | | | | | Move mx6 specific defines to arch-mx6 directory. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Stefano Babic <sbabic@denx.de>
* i.mx: iomux-v3.h: move to imx-common include directoryTroy Kisky2012-07-31-0/+214
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
generated by cgit v1.1 at 2024-09-13 15:35:10 +0000