summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-omap5
Commit message (Collapse)AuthorAgeLines
* ARM: OMAP5: DRA7xx: Add support for power rail groupingLubomir Popov2015-01-29-3/+17
| | | | | | | | | | | | | | | | | | | | | | On the DRA72x (J6Eco) EVM one PMIC SMPS is powering three SoC core rails. This concept of using one SMPS to supply multiple core domains (in various, although limited combinations, per primary device use case) has now become common and is used by many customer J6/J6Eco designs; it is supported by a number of corresponding PMIC OTP versions. This patch implements correct operation of the core voltages scaling routine by ensuring that each SMPS that is supplying more than one domain shall be written only once, and with the highest voltage of those fused in the SoC (or of those defined in the corresponding header if fuse read is disabled or fails) for the power rails belonging to the group. The patch also replaces some PMIC-related magic numbers with the appropriate definitions. The default OPP_NOM voltages for the DRA7xx SoCs are updated as well, per the latest DMs. Signed-off-by: Lubomir Popov <l-popov@ti.com>
* arm: omap: add support for am57xx devicesFelipe Balbi2014-12-04-3/+3
| | | | | | | | just add a few ifdefs around because this device is very similar to dra7xxx. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* arm: omap5: tps659038: rename regulator definesFelipe Balbi2014-12-04-5/+5
| | | | | | | | | Those regulators don't have any coupling with what they supply, so remove the suffixes in order to not confuse anybody. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* board/ti/dra7xx: add support for parallel NORpekon gupta2014-08-25-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM. The Flash device is connected to GPMC controller on chip-select[0] and accessed as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and is CFI compatible. As multiple devices are share GPMC pins on this board, so following board settings are required to detect NOR device: SW5.1 (NAND_BOOTn) = OFF (logic-1) SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */ SW5.3 (eMMC_BOOTn) = OFF (logic-1) SW5.4 (QSPI_BOOTn) = OFF (logic-1) And also set appropriate SYSBOOT configurations: SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */ SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */ SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */ SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */ SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */ SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */ SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */ SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */ Also, following changes are required to enable NOR Flash support in dra7xx_evm board profile:
* armv7:TI: Add <asm/ti-common/sys_proto.h> and migrate omap_hw_init_contextTom Rini2014-05-23-54/+1
| | | | | | | | | | | | | The omap_hw_init_context function (and assorted helpers) is the same for all OMAP-derived parts as when CHSETTINGS are used, that's the same and our DDR base is also always the same. In order to make this common we simply need to update the names of the define for DDR address space which is also common. Cc: Sricharan R. <r.sricharan@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA72x: Add Silicon ID supportLokesh Vutla2014-05-23-0/+1
| | | | | | | Add silicon ID code for DRA722 silicon. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
* ARM: omap5: add platform specific info for GPMC and ELM controllerspekon gupta2014-05-23-6/+90
| | | | | | | | | | | | | | | | This patch moves platform specific information for GPMC and ELM controller into separate header files, so that any derivative devices do not mess other header files. Platform specific information added into arch-xx/../hardware.h - CPU related platform specific details like base-address of GPMC and ELM Platform specific information added into arch-xx/../mem.h - Generic configs for GPMC and ELM initialization. - Hardware parameters or constrains specific to GPMC and ELM IP like; number of max number of chip-selects available Signed-off-by: Pekon Gupta <pekon@ti.com>
* ARM: OMAP5: add CKO buffer control maskDmitry Lifshitz2014-05-13-0/+3
| | | | | | Add CKOBUFFER_CLK_EN bit mask enabling FREF_XTAL_CLK clock. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
* ARM: OMAP5: add UART4 supportDmitry Lifshitz2014-05-13-0/+1
| | | | | | Add UART4 base address. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
* ARM: OMAP: hide custom bit manipulation function sr32()Wolfgang Denk2014-04-17-1/+0
| | | | | | | | | | The only remaining user of the custom bit manipulation function sr32() is arch/arm/cpu/armv7/omap3/clock.c, so make it a static function in that file to prepare complete removal. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* spl: Fix guardian macros in spl.hMarek Vasut2014-03-28-1/+1
| | | | | | | | | Fix the macros guarding the spl.h header for various platforms. Due to a typo and a propagation of it, the macros went out-of-sync with their ifdef check, so fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com>
* mtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nandpekon gupta2014-03-04-1/+1
| | | | | | | | | omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms. Hence this file should be present in generic folder instead of architecture specific include folder. Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5 Signed-off-by: Pekon Gupta <pekon@ti.com>
* mtd: nand: omap: merge duplicate GPMC data from different arch-xx headers ↵pekon gupta2014-03-04-45/+1
| | | | | | | | | | | | | | | into common omap_gpmc.h Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related defines and declarations scattered in SoC platform specific header files like include/asm/arch-xx/cpu.h However, GPMC hardware remains same across all platforms thus this patch merges GPMC data scattered across different arch-xx specific header files into single header file include/asm/arch/omap_gpmc.h Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5 Signed-off-by: Pekon Gupta <pekon@ti.com>
* ARM: O5/dra7xx: Add SATA boot supportDan Murphy2014-02-19-9/+1
| | | | | | | | | | | | | Add the SATA boot support for OMAP5 and dra7xx. Renamed the omap_sata_init to the common init_sata(int dev) for commonality in with sata stack. Added the ROM boot device ID for SATA. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* DRA7: add ABB setup for MPU voltage domainNishanth Menon2014-01-24-0/+2
| | | | | | | | | Patch adds modification to shared omap5 abb_setup() function, and proper registers definitions needed for ABB setup sequence. ABB is initialized for MPU voltage domain at OPP_NOM. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* DRA7: Add support for ES1.1 silicon ID codeNishanth Menon2014-01-24-0/+1
| | | | | | | | ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support for ES1.1 IDCODE change. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALLJassi Brar2014-01-24-1/+0
| | | | | | | | | The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
* ARM: OMAP5: Add SATA platform glueRoger Quadros2013-12-04-0/+48
| | | | | | Add platform glue logic for the SATA controller. Signed-off-by: Roger Quadros <rogerq@ti.com>
* ARM: OMAP5: Add PRCM and Control information for SATARoger Quadros2013-12-04-0/+6
| | | | | | | Adds the necessary PRCM and Control register information for SATA on OMAP5. Signed-off-by: Roger Quadros <rogerq@ti.com>
* ARM: DRA: EMIF: Change DDR3 settings to use hw levelingSRICHARAN R2013-12-04-0/+1
| | | | | | | | | | Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using software leveling. This was done since hardware leveling was not working. Now that the right sequence to do hw leveling is identified, use it. This is required for EMIF clockdomain to idle and come back during lowpower usecases. Signed-off-by: Sricharan R <r.sricharan@ti.com>
* Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-09-2/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
| * ARM: OMAP5: DDR3: Change io settingsSRICHARAN R2013-11-01-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The change from 0x64656465 to 0x64646464 is to remove the weak pull enabled on DQS, nDQS lines. This pulls the differential signals in the same direction which is not intended. So disabling the weak pulls improves signal integrity. On the uEVM there are 4 DDR3 devices. The VREF for 2 of the devices is powered by the OMAP's VREF_CA_OUT pins. The VREF on the other 2 devices is powered by the OMAP's VREF_DQ_OUT pins. So the net effect here is that only half of the DDR3 devices were being supplied a VREF! This was clearly a mistake. The second change improves the robustness of the interface and was specifically seen to cure corruption observed at high temperatures on some boards. With the above two changes better memory stability was observed with extended temperature ranges around 100C. Signed-off-by: Sricharan R <r.sricharan@ti.com>
| * dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 buildMinal Shah2013-11-01-0/+1
| | | | | | | | | | | | | | | | | | | | | | UART booting is supported on this SoC, but via UART3 rather than UART1. Because of this we must change the board to use UART3 for all console access (only one UART is exposed on this board and a slight HW mod is required to switch UARTs). Signed-off-by: Minal Shah <minal.shah@ti.com> [trini: Make apply to mainline, reword commit] Signed-off-by: Tom Rini <trini@ti.com>
* | usb: dra7xx: Add support for dra7xx xhci USB hostDan Murphy2013-10-20-0/+4
| | | | | | | | | | | | | | | | | | | | | | Add the support for the dra7xx xhci usb host. dra7xx does not contain an EHCI controller so the headers can be removed from the board file. The xHCI host on dra7xx is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | usb: omap: Move the xhci-omap header file to common locationDan Murphy2013-10-20-124/+0
| | | | | | | | | | | | | | Moving the xhci-omap header to a more global location so that other code can reference this code. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | OMAP5: USB: Add OMAP xHCI file and headerDan Murphy2013-10-20-0/+124
| | | | | | | | | | | | | | | | Add the OMAP file for the xHCI Host controller This code will initilialize the proper components within the OMAP5 to enable the xHCI host controller. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | ARM: OMAP5: Add registers and defines for USBOTG SSDan Murphy2013-10-20-0/+10
|/ | | | | | | Add the prcm registers and the bit definitions to enable the USB SS port of the OMAP5 device. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* omap5: add qspi supportMatt Porter2013-10-07-0/+4
| | | | | | | | Add QSPI definitions and clock configuration support. Signed-off-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* arm: omap5: echi: Add GPL-2.0+ SPDX-License-IdentifierNobuhiro Iwamatsu2013-09-20-14/+1
| | | | Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-09-04-1/+10
|\
| * omap5: Expand CONFIG_SPL_MAX_SIZE and comment upon SRAM_SCRATCH_SPACE_ADDRTom Rini2013-08-28-1/+10
| | | | | | | | | | | | | | | | | | After examining both TRMs and doing some experimentation, we can rely on using the start of the download area for CONFIG_SPL_TEXT_BASE and then move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for peripheral boot modes such as UART. Signed-off-by: Tom Rini <trini@ti.com>
* | ARM: OMAP5: USB: Add OMAP5 common USB EHCI informationDan Murphy2013-08-26-0/+60
| | | | | | | | | | | | | | | | * Enable the OMAP5 EHCI host clocks * Add OMAP5 EHCI register definitions * Add OMAP5 ES2 host revision Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | SPDX-License-Identifier: fixing some problematic GPL-2.0 filesWolfgang Denk2013-08-19-18/+1
|/ | | | | | | | | | | | | | | | | Unlike the other patches in this series so far, this commit fixes a ambiguity in the license terms for some OMAP files: the code was originally derived from the Linux kernel sources, where it was clearly marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot version had a GPL-2.0+ file header added, apparently without permission / relicensing from the original authors of the code. Insert a GPL-2.0 SPDX-License-Identifier to fix this. Signed-off-by: Wolfgang Denk <wd@denx.de> cc: Tom Rix <Tom.Rix@windriver.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Tom Rini <trini@ti.com>
* ARM: DRA7xx: Add CPSW support to DRA7xx EVMMugunthan V N2013-07-26-0/+32
| | | | | | Adding support for CPSW Ethernet support found in DRA7xx EVM Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-134/+8
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-07-12-0/+4
|\ | | | | | | | | | | | | | | | | | | Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and serial. Conflicts: arch/arm/dts/exynos5250.dtsi Signed-off-by: Tom Rini <trini@ti.com>
| * ARM: OMAP: GPIO: Fix valid range and enable usage of all GPIOs on OMAP5Axel Lin2013-07-02-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs. These SoCs have different gpio count but currently omap_gpio driver uses hard coded 192 which is wrong. This patch fixes this issue by: 1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h. 2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5. Thanks for Lubomir Popov to provide valuable comments to fix this issue. Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Acked-by: Heiko Schocher <hs@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-06-13-72/+112
|\ \ | |/ | | | | | | | | | | | | | | Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR Conflicts: arch/arm/include/asm/arch-omap5/omap.h Signed-off-by: Tom Rini <trini@ti.com>
| * OMAP5: Enable access to auxclk registersLubomir Popov2013-06-10-0/+18
| | | | | | | | | | | | | | | | | | | | auxclk0 and auxclk1 are utilized on some OMAP5 boards. Define the infrastructure needed for accessing them without using magic numbers. Also remove unrelated TPS62361 defines from clocks.h Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
| * ARM: DRA7xx: EMIF: Change settings required for EVM boardSricharan R2013-06-10-0/+1
| | | | | | | | | | | | | | | | | | | | | | DRA7 EVM board has the below configuration. Adding the settings for the same here. 2Gb_1_35V_DDR3L part * 2 on EMIF1 2Gb_1_35V_DDR3L part * 4 on EMIF2 Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7xx: clocks: Update PLL valuesLokesh Vutla2013-06-10-1/+7
| | | | | | | | | | | | | | | | | | | | | | Update PLL values. SYS_CLKSEL value for 20MHz is changed to 2. In other platforms SYS_CLKSEL value 2 represents reserved. But in sys_clk array ind 1 is used for 13Mhz. Since other platforms are not using 13Mhz, reusing index 1 for 20MHz. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Sricharan R <r.sricharan@ti.com>
| * ARM: DRA7xx: Update pinmux dataLokesh Vutla2013-06-10-2/+5
| | | | | | | | | | | | | | Updating pinmux data as specified in the latest DM Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com>
| * mmc: omap_hsmmc: Update pbias programmingBalaji T K2013-06-10-1/+1
| | | | | | | | | | | | | | Update pbias programming sequence for OMAP5 ES2.0/DRA7 Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7xx: Correct SRAM END addressSricharan R2013-06-10-5/+6
| | | | | | | | | | | | | | | | NON SECURE SRAM is 512KB in DRA7xx devices. So fixing it here. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7xx: Correct the SYS_CLK to 20MHZSricharan R2013-06-10-0/+8
| | | | | | | | | | | | | | | | | | | | The sys_clk on the dra evm board is 20MHZ. Changing the configuration for the same. And also moving V_SCLK, V_OSCK defines to arch/clock.h for OMAP4+ boards. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: OMAP5: DRA7xx: support class 0 optimized voltagesNishanth Menon2013-06-10-0/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | DRA752 now uses AVS Class 0 voltages which are voltages in efuse. This means that we can now use the optimized voltages which are stored as mV values in efuse and program PMIC accordingly. This allows us to go with higher OPP as needed in the system without the need for implementing complex AVS logic. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7xx: power Add support for tps659038 PMICLokesh Vutla2013-06-10-0/+16
| | | | | | | | | | | | | | | | TPS659038 is the power IC used in DRA7XX boards. Adding support for this and also adding pmic data for DRA7XX boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7xx: Add control id code for DRA7xxLokesh Vutla2013-06-10-2/+9
| | | | | | | | | | | | | | | | The registers that are used for device identification are changed from OMAP5 to DRA7xx. Using the correct registers for DRA7xx. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: OMAP4+: pmic: Make generic bus init and write functionsLokesh Vutla2013-06-10-1/+1
| | | | | | | | | | | | | | | | | | | | Voltage scaling can be done in two ways: -> Using SR I2C -> Using GP I2C In order to support both, have a function pointer in pmic_data so that we can call as per our requirement. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: OMAP2+: Rename asm/arch/clocks.h asm/arch/clock.hLokesh Vutla2013-06-10-2/+2
| | | | | | | | | | | | | | To be consistent with other ARM platforms, renaming asm/arch-omap*/clocks.h to asm/arch-omap*/clock.h Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
generated by cgit v1.1 at 2024-11-05 18:38:33 +0000