summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-omap5/omap.h
Commit message (Collapse)AuthorAgeLines
* TI: Rework SRAM definitions and maximumsTom Rini2016-09-06-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On all TI platforms the ROM defines a "downloaded image" area at or near the start of SRAM which is followed by a reserved area. As it is at best bad form and at worst possibly harmful in corner cases to write in this reserved area, we stop doing that by adding in the define NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this. At current we define the end of scratch space at 0x228 bytes past the start of scratch space this this gives us a lot of room to grow. As these scratch uses are non-optional today, all targets are modified to respect this boundary. Tested on OMAP4 Pandaboard, OMAP3 Beagle xM Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Paul Kocialkowski <contact@paulk.fr> Cc: Enric Balletbo i Serra <eballetbo@gmail.com> Cc: Adam Ford <aford173@gmail.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Stefan Roese <sr@denx.de> Cc: Thomas Weber <weber@corscience.de> Cc: Hannes Schmelzer <oe5hpm@oevsv.at> Cc: Thomas Chou <thomas@wytron.com.tw> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Simon Glass <sjg@chromium.org> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Sam Protsenko <semen.protsenko@linaro.org> Cc: Heiko Schocher <hs@denx.de> Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Cc: Ben Whitten <ben.whitten@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: "B, Ravi" <ravibabu@ti.com> Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Ash Charles <ashcharles@gmail.com> Cc: "Kipisz, Steven" <s-kipisz2@ti.com> Cc: Daniel Allred <d-allred@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Ladislav Michl <ladis@linux-mips.org>
* ARM: DRA7: Add ABB setup for all domainsNishanth Menon2016-04-25-0/+3
| | | | | | | | | | | | | ABB should be initialized for all required domains voltage domain for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If we do not do this, kernel configuring just the frequency using the default boot loader configured voltage can fail on many corner lot units and has been hard to debug. This specifically is a concern with DRA7 generation of SoCs since other than VDD_MPU, all other domains are only permitted to setup the voltages to required OPP only at boot. Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM: OMAP5: Enable ABB configuration for MM voltage domainNishanth Menon2016-04-25-0/+1
| | | | | | | | | | Since we setup the voltage and frequency for the MM domain, we *must* setup the ABB configuration needed for the domain as well. If we do not do this, kernel configuring just the frequency using the default boot loader configured voltage can fail on many corner lot units. Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM: DRA72x: Add support for detection of SR2.0Ravi Babu2016-03-27-0/+1
| | | | | | | | | Add support for detection of SR2.0 version of DRA72x family of processors. Signed-off-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: OMAP5: added USB initializtion codeKishon Vijay Abraham I2015-08-28-0/+6
| | | | | | | | | Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in omap5 board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: beagle_x15: added USB initializtion codeKishon Vijay Abraham I2015-08-28-1/+1
| | | | | | | | | Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in beagle_x15 board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA74-evm: Use SMA_1 spare register to workaround DP83865 phy on SR2.0Nishanth Menon2015-08-28-0/+2
| | | | | | | | | | | | | | | | | | | DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet provided IODELAY values for standard RGMII phys do not work. Silicon Revision(SR) 2.0 provides an alternative bit configuration that allows us to do a "gross adjustment" to launch the data off a different internal clock edge. Manual IO Delay overrides are still necessary to fine tune the clock-to-data delays. This is a necessary workaround for the quirky ethernet Phy we have on the platform. NOTE: SMA registers are spare "kitchen sink" registers that does contain bits for other workaround as necessary as well. Hence the control for the same is introduced in a generic SoC specific, board generic location. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7: Add detection of ES2.0Nishanth Menon2015-08-28-0/+1
| | | | | | | | | | | | | | | | | Add support for detection of ES2.0 version of DRA7 family of processors. ES2.0 is an incremental revision with various fixes including the following: - reset logic fixes - few assymetric aging logic fixes - MMC clock rate fixes - Ethernet speed fixes - edma fixes for mcasp [ravibabu@ti.com: posted internal for an older bootloader] Signed-off-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* omap-common: Common boot code OMAP3 support and cleanupPaul Kocialkowski2015-07-27-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This introduces OMAP3 support for the common omap boot code, as well as a major cleanup of the common omap boot code. First, the omap_boot_parameters structure becomes platform-specific, since its definition differs a bit across omap platforms. The offsets are removed as well since it is U-Boot's coding style to use structures for mapping such kind of data (in the sense that it is similar to registers). It is correct to assume that romcode structure encoding is the same as U-Boot, given the description of these structures in the TRMs. The original address provided by the bootrom is passed to the U-Boot binary instead of a duplicate of the structure stored in global data. This allows to have only the relevant (boot device and mode) information stored in global data. It is also expected that the address where the bootrom stores that information is not overridden by the U-Boot SPL or U-Boot. The save_omap_boot_params is expected to handle all special cases where the data provided by the bootrom cannot be used as-is, so that spl_boot_device and spl_boot_mode only return the data from global data. All of this is only relevant when the U-Boot SPL is used. In cases it is not, save_boot_params should fallback to its weak (or board-specific) definition. save_omap_boot_params should not be called in that context either. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* ARM: DRA7: CPSW: Remove IO delay hackLokesh Vutla2015-06-12-25/+0
| | | | | | | | Now all manual mode configurations are done as part of IO delay recalibration sequence, remove the hack done for CPSW. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* board: ti: DRA7: added USB initializtion codeKishon Vijay Abraham I2015-04-14-0/+12
| | | | | | | | | Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in dra7xx board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
* arm: omap: add support for am57xx devicesFelipe Balbi2014-12-04-2/+2
| | | | | | | | just add a few ifdefs around because this device is very similar to dra7xxx. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* armv7:TI: Add <asm/ti-common/sys_proto.h> and migrate omap_hw_init_contextTom Rini2014-05-23-5/+0
| | | | | | | | | | | | | The omap_hw_init_context function (and assorted helpers) is the same for all OMAP-derived parts as when CHSETTINGS are used, that's the same and our DDR base is also always the same. In order to make this common we simply need to update the names of the define for DDR address space which is also common. Cc: Sricharan R. <r.sricharan@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA72x: Add Silicon ID supportLokesh Vutla2014-05-23-0/+1
| | | | | | | Add silicon ID code for DRA722 silicon. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Tom Rini <trini@ti.com>
* ARM: omap5: add platform specific info for GPMC and ELM controllerspekon gupta2014-05-23-3/+0
| | | | | | | | | | | | | | | | This patch moves platform specific information for GPMC and ELM controller into separate header files, so that any derivative devices do not mess other header files. Platform specific information added into arch-xx/../hardware.h - CPU related platform specific details like base-address of GPMC and ELM Platform specific information added into arch-xx/../mem.h - Generic configs for GPMC and ELM initialization. - Hardware parameters or constrains specific to GPMC and ELM IP like; number of max number of chip-selects available Signed-off-by: Pekon Gupta <pekon@ti.com>
* ARM: OMAP5: add UART4 supportDmitry Lifshitz2014-05-13-0/+1
| | | | | | Add UART4 base address. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
* DRA7: add ABB setup for MPU voltage domainNishanth Menon2014-01-24-0/+2
| | | | | | | | | Patch adds modification to shared omap5 abb_setup() function, and proper registers definitions needed for ABB setup sequence. ABB is initialized for MPU voltage domain at OPP_NOM. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* DRA7: Add support for ES1.1 silicon ID codeNishanth Menon2014-01-24-0/+1
| | | | | | | | ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support for ES1.1 IDCODE change. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP5: Add PRCM and Control information for SATARoger Quadros2013-12-04-0/+3
| | | | | | | Adds the necessary PRCM and Control register information for SATA on OMAP5. Signed-off-by: Roger Quadros <rogerq@ti.com>
* ARM: DRA: EMIF: Change DDR3 settings to use hw levelingSRICHARAN R2013-12-04-0/+1
| | | | | | | | | | Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using software leveling. This was done since hardware leveling was not working. Now that the right sequence to do hw leveling is identified, use it. This is required for EMIF clockdomain to idle and come back during lowpower usecases. Signed-off-by: Sricharan R <r.sricharan@ti.com>
* ARM: OMAP5: DDR3: Change io settingsSRICHARAN R2013-11-01-2/+2
| | | | | | | | | | | | | | | | | | | The change from 0x64656465 to 0x64646464 is to remove the weak pull enabled on DQS, nDQS lines. This pulls the differential signals in the same direction which is not intended. So disabling the weak pulls improves signal integrity. On the uEVM there are 4 DDR3 devices. The VREF for 2 of the devices is powered by the OMAP's VREF_CA_OUT pins. The VREF on the other 2 devices is powered by the OMAP's VREF_DQ_OUT pins. So the net effect here is that only half of the DDR3 devices were being supplied a VREF! This was clearly a mistake. The second change improves the robustness of the interface and was specifically seen to cure corruption observed at high temperatures on some boards. With the above two changes better memory stability was observed with extended temperature ranges around 100C. Signed-off-by: Sricharan R <r.sricharan@ti.com>
* omap5: add qspi supportMatt Porter2013-10-07-0/+3
| | | | | | | | Add QSPI definitions and clock configuration support. Signed-off-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* omap5: Expand CONFIG_SPL_MAX_SIZE and comment upon SRAM_SCRATCH_SPACE_ADDRTom Rini2013-08-28-1/+10
| | | | | | | | | After examining both TRMs and doing some experimentation, we can rely on using the start of the download area for CONFIG_SPL_TEXT_BASE and then move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for peripheral boot modes such as UART. Signed-off-by: Tom Rini <trini@ti.com>
* ARM: DRA7xx: Add CPSW support to DRA7xx EVMMugunthan V N2013-07-26-0/+26
| | | | | | Adding support for CPSW Ethernet support found in DRA7xx EVM Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-06-13-37/+30
|\ | | | | | | | | | | | | | | | | Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR Conflicts: arch/arm/include/asm/arch-omap5/omap.h Signed-off-by: Tom Rini <trini@ti.com>
| * ARM: DRA7xx: EMIF: Change settings required for EVM boardSricharan R2013-06-10-0/+1
| | | | | | | | | | | | | | | | | | | | | | DRA7 EVM board has the below configuration. Adding the settings for the same here. 2Gb_1_35V_DDR3L part * 2 on EMIF1 2Gb_1_35V_DDR3L part * 4 on EMIF2 Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * mmc: omap_hsmmc: Update pbias programmingBalaji T K2013-06-10-1/+1
| | | | | | | | | | | | | | Update pbias programming sequence for OMAP5 ES2.0/DRA7 Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7xx: Correct SRAM END addressSricharan R2013-06-10-5/+6
| | | | | | | | | | | | | | | | NON SECURE SRAM is 512KB in DRA7xx devices. So fixing it here. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: DRA7xx: Add control id code for DRA7xxLokesh Vutla2013-06-10-2/+9
| | | | | | | | | | | | | | | | The registers that are used for device identification are changed from OMAP5 to DRA7xx. Using the correct registers for DRA7xx. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * ARM: OMAP4+: Cleanup header filesLokesh Vutla2013-06-10-30/+1
| | | | | | | | | | | | | | After having the u-boot clean up series, there are many definitions that are unused in header files. Removing all those unused ones. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
| * OMAP3+: introduce generic ABB supportAndrii Tseglytskyi2013-06-10-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adaptive Body Biasing (ABB) modulates transistor bias voltages dynamically in order to optimize switching speed versus leakage. Adaptive Body-Bias ldos are present for some voltage domains starting with OMAP3630. There are three modes of operation: * Bypass - the default, it just follows the vdd voltage * Foward Body-Bias - applies voltage bias to increase transistor performance at the cost of power. Used to operate safely at high OPPs. * Reverse Body-Bias - applies voltage bias to decrease leakage and save power. Used to save power at lower OPPs. Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com> Acked-by: Nishanth Menon <nm@ti.com>
* | am33xx/omap4+: Move SRAM_SCRATCH_SPACE_ADDR to <asm/arch/omap.h>Tom Rini2013-06-06-0/+1
|/ | | | | | | | | | The location of valid scratch space is dependent on SoC, so move that there. On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR. On am33xx/ti814x we want to use what the ROM defines as "public stack" which is the area after our defined download image space. Correct the comment about and location of CONFIG_SPL_TEXT_BASE. Signed-off-by: Tom Rini <trini@ti.com>
* ARM: OMAP4/5: Make OMAPx_SRAM_SCRATCH_ defines commonSRICHARAN R2013-05-10-13/+0
| | | | | | | | These defines are same across OMAP4/5. So move them to omap_common.h. This is required for the patches that follow. Signed-off-by: Sricharan R <r.sricharan@ti.com>
* ARM: OMAP: Make omap_boot_parameters common across socsSRICHARAN R2013-05-10-23/+0
| | | | | | | | omap_boot_parameters is same and defined for each soc. So move this to a common place to reuse it across socs. Signed-off-by: Sricharan R <r.sricharan@ti.com>
* arm: omap4: Fix SDRAM AUTO DETECTIONLokesh Vutla2013-04-08-1/+0
| | | | | | | | | | | | | | Commit "8602114 omap: emif: configure emif only when required" breaks SDRAM_AUTO_DETECTION. The issue is dmm_init() depends on emif_sizes[](SDRAM Auto detection) done in do_sdram_init(). The above commit moves dmm_init() above do_sdram_init() because of which dmm_init() uses uninitialized emif_sizes[]. So instead of using global emif_sizes[], get sdram details locally and calculate emif sizes. Reported-by: Michael Cashwell <mboards@prograde.net> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* arm: dra7xx: Add silicon id support for DRA752 socLokesh Vutla2013-03-11-0/+1
| | | | | | | | Adding CPU detection support for the DRA752 ES1.0 soc. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP5: srcomp: enable slew rate compensation cells after powerupLokesh Vutla2013-03-11-0/+19
| | | | | | | | | | | | | | After power-up SRCOMP cells are by-passed by default in OMAP5. Software has to enable these SRCOMP sells. For ES2: All 5 SRCOMP cells needs to be enabled. For ES1: Only 4 SRCOMP cells in core power domain are enabled. The 1 in wkup domain is not enabled because smart i/os of wkup domain work with default compensation code. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
* ARM: OMAP5: Add DDR changes required for OMAP543X ES2.0 SOCsLokesh Vutla2013-03-11-0/+6
| | | | | | | | | | | | | Add pre calculated timing settings of LPDDR2 and DDR3 memories present in OMAP5430 and OMAP5432 ES2.0 versions. Also adding the DDR pad io settings required for OMAP543X SOCs here. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Cc: Tom Rini <trini@ti.com>
* ARM: OMAP5: Add silicon id support for ES2.0 revision.SRICHARAN R2013-03-11-0/+2
| | | | | | | | | Adding the CPU detection suport for OMAP5430 and OMAP5432 ES2.0 SOCs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Cc: Tom Rini <trini@ti.com> Cc: Nishanth Menon <nm@ti.com>
* ARM: OMAP5: Clean up iosettings codeLokesh Vutla2013-03-11-0/+10
| | | | | | | | | | | There is some code duplication in the ddr io settings code. This is avoided by moving the data to a Soc specific place and letting the code generic. This avoids unnessecary code addition for future socs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Make control module register structure genericLokesh Vutla2013-03-11-82/+2
| | | | | | | | | | | | A seperate omap_sys_ctrl_regs structure is defined for omap4 & 5. If there is any change in control module for any of the ES versions, a new structure needs to be created. In order to remove this dependency, making the register structure generic for all the omap4+ boards. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Clean up the pmic codeSRICHARAN R2013-03-11-1/+2
| | | | | | | | | | The pmic code is duplicated for OMAP 4 and 5. Instead move the data to Soc specific place and share the code. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Cleanup the clocks layerSRICHARAN R2013-03-11-1/+2
| | | | | | | | | | | | | | | Currently there is quite a lot of code which is duplicated in the clocks code for OMAP 4 and 5 Socs. Avoiding this here by moving the clocks data to a SOC specific place and the sharing the common code. This helps in addition of a new Soc with minimal changes. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ARM: OMAP4+: Change the PRCM structure prototype common for all SocsSRICHARAN R2013-03-11-1/+2
| | | | | | | | | | | | The current PRCM structure prototype directly matches the hardware register layout. So there is a need to change this for every new silicon revision which has register space changes. Avoiding this by making the prototye generic and populating the register addresses seperately for all Socs. Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* omap4/5/am33xx: Make lowlevel_init available to all armv7 platformsTom Rini2012-09-01-2/+0
| | | | | | | | | | | | | | Make the lowlevel_init function that these platforms have which just sets up the stack and calls a C function available to all armv7 platforms. As part of this we change some of the macros that are used to be more clear. Previously (except for am335x evm) we had been setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are equivalent to simply referencing NON_SECURE_SRAM_END. On am335x evm we should have been doing this initially and do now. Cc: Sricharan R <r.sricharan@ti.com> Tested-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Rini <trini@ti.com>
* OMAP5: Configure the io settings for omap5432 uevm boardLokesh Vutla2012-07-07-1/+14
| | | | | | This patch adds the IO settings required for OMAP5432 uevm's DDR3 pads Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* OMAP5: ADD chip detection for OMAP5432 SOCLokesh Vutla2012-07-07-1/+2
| | | | | | This patch adds chip detection for OMAP5432 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* OMAP5: Adding correct Control id code for OMAP5430Lokesh Vutla2012-07-07-1/+1
| | | | | | | Control id code for omap5430 ES1.0 is hard coded with a wrong value. This patch corrects the value Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: OMAP5: Correct the DRAM_ADDR_SPACE_END macro.SRICHARAN R2012-07-07-1/+1
| | | | | | | OMAP5 evm board has 2GB of memory. So correct the macro to take in to account of the full dram size. Signed-off-by: R Sricharan <r.sricharan@ti.com>
generated by cgit v1.1 at 2024-11-08 19:20:04 +0000