summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-omap4
Commit message (Collapse)AuthorAgeLines
* OMAP4+: Force DDR in self-refresh after warm resetLokesh Vutla2012-07-07-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Errata ID:i727 Description: The refresh rate is programmed in the EMIF_SDRAM_REF_CTRL[15:0] REG_REFRESH_RATE parameter taking into account frequency of the device. When a warm reset is applied on the system, the OMAP processor restarts with another OPP and so frequency is not the same. Due to this frequency change, the refresh rate will be too low and could result in an unexpected behavior on the memory side. Workaround: The workaround is to force self-refresh when coming back from the warm reset with the following sequence: • Set EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x2 • Set EMIF_PWR_MGMT_CTRL[7:4] REG_SR_TIM to 0x0 • Do a dummy read (loads automatically new value of sr_tim) This will reduce the risk of memory content corruption, but memory content can't be guaranteed after a warm reset. This errata is impacted on OMAP4430: 1.0, 2.0, 2.1, 2.2, 2.3 OMAP4460: 1.0, 1.1 OMAP4470: 1.0 OMAP5430: 1.0 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com> Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
* ARM: OMAP3+: Detect reset typeLokesh Vutla2012-07-07-0/+3
| | | | | | | | | | | | Certain modules are not affected by means of a warm reset and need not be configured again. Adding an API to detect the reset reason warm/cold. This will be used to skip the module configurations that are retained across a warm reset. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP4: Correct the lpddr2 io settings register value.SRICHARAN R2012-07-07-1/+1
| | | | | | | | | | To meet certain timing requirements on the lpddr2 cmd and data phy interfaces ,lpddr iopads have to be configured as differential buffers and a Vref has to be internally generated and provided to these buffers. Correcting the above settings here. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP5: DPLL core lock for OMAP5432Lokesh Vutla2012-07-07-0/+5
| | | | | | | No need to Unlock DPLL initially. DDR3 can work at normal OPP from initialozation Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* omap4+: Avoid using __attribute__ ((__packed__))Aneesh V2012-05-15-1/+1
| | | | | | | | | | | | | Avoid using __attribute__ ((__packed__)) unless it's absolutely necessary. "packed" will remove alignment requirements for the respective objects and may cause alignment issues unless alignment is also enforced using a pragma. Here, these packed attributes were causing alignment faults in Thumb build. Signed-off-by: Aneesh V <aneesh@ti.com>
* OMAP3+: reset: Create a common reset layer.SRICHARAN R2012-05-15-11/+11
| | | | | | | | | The reset.S has the function to do a warm reset on OMAP based socs. Moving this to a reset.c file so that this acts a common layer to add any reset related functionality for the future. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP4/5: device: Add support to get the device type.SRICHARAN R2012-05-15-0/+4
| | | | | | Add support to identify the device as GP/EMU/HS. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP4/5: Make the sysctrl structure commonSRICHARAN R2012-05-15-4/+6
| | | | | | | | | Make the sysctrl structure common, so that it can be used in generic functions across socs. Also change the base address of the system control module, to include all the registers and not simply the io regs. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP4/5: Make the silicon revision variable common.SRICHARAN R2012-05-15-6/+0
| | | | | | | | The different silicon revision variable names was defined for OMAP4 and OMAP5 socs. Making the variable common so that some code can be made generic. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP5: palmas: Configure nominal opp vdd valuesSRICHARAN R2012-05-15-0/+1
| | | | | | | | | | | The nominal opp vdd values as recommended for ES1.0 silicon is set for mpu, core, mm domains using palmas. Also used the right sequence to enable the vcores as per a previous patch from Nishant Menon, which can be dropped now. http://lists.denx.de/pipermail/u-boot/2012-March/119151.html Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP4460: TPS Ensure SET1 is selected after voltage configurationNishanth Menon2012-05-15-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms. Currently we control this pin with a mux configuration as part of boot sequence. Current configuration results in the following voltage waveform: |---------------| (SET1 default 1.4V) | --------(programmed voltage) | <- (This switch happens on mux7,pullup) vdd_mpu(TPS) -----/ (OPP boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -----------------------/ (OPP boot voltage) Problem 1) |<----- Tx ------>| timing violation for a duration Tx close to few milliseconds. Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP. By using GPIO as recommended as standard procedure by TI, the sequence changes to: -------- (programmed voltage) vdd_mpu(TPS) ------------/ (Opp boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -------------/ (OPP boot voltage) NOTE: This does not attempt to address OMAP5 - Aneesh please confirm Reported-by: Isabelle Gros <i-gros@ti.com> Reported-by: Jerome Angeloni <j-angeloni@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* OMAP3+: Introduce generic logic for OMAP voltage controllerNishanth Menon2012-05-15-15/+2
| | | | | | | | | | | | | | | | | | | | OMAP Voltage controller is used to generically talk to PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code in multiple SoC code, introduce a common voltage controller logic which can be re-used from elsewhere. With this change, we replace setup_sri2c with omap_vc_init which has the same functionality, and replace the voltage scale replication in do_scale_vcore and do_scale_tps62361 with omap_vc_bypass_send_value. omap_vc_bypass_send_value can also now be used with any configuration of PMIC. NOTE: Voltage controller controlling I2C_SR is a write-only data path, so no register read operation can be implemented. Reported-by: Isabelle Gros <i-gros@ti.com> Reported-by: Jerome Angeloni <j-angeloni@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM:OMAP+:MMC: Add parameters to MMC initJonathan Solnit2012-05-15-1/+1
| | | | | | | | | | Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
* omap_hsmmc: Wait for CMDI to be clearTom Rini2012-02-15-1/+1
| | | | | | | | | | | | | | | | | Before we can send a command we need both the DATI (command inhibit on mmc_dat line) bit and CMDI (command inhibit on mmc_cmd line) are clear. The previous behavior of only checking on DATI was insufficient on some cards and incorrect behavior in any case. This makes the code check for both bits being clear and makes the error print more clear as to what happened. DATI_CMDDIS is removed as it was unused elsewhere in the code and stood for 'DATI is set, cmds are disabled still'. Fix originally spotted by Peter Bigot. Tested-by: Peter A. Bigot <bigotp@acm.org> Tested-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Andreas Müller <schnitzeltony@googlemail.com>
* ehci-omap: Clean up added ehci-omap.cGovindraj.R2012-02-12-0/+49
| | | | | | | | | | | | | | | | | | Clean up added ehci-omap.c and make it generic for re-use across omap-soc having same ehci ip block. Also pass the modes to be configured from board file and configure the ports accordingly. All usb layers are not cache aligned, till then keep cache off for usb ops as ehci will use internally dma for all usb ops. * Add a generic common header ehci-omap.h having common ip block data and reg shifts. * Rename and modify ehci-omap3 to ehci.h retain only conflicting sysc reg shifts remove others and move to common header file. * pass the board data for beagle/panda accordinly to use ehci ports. Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
* omap_rev_string: output to stdoutAndreas Müller2012-01-16-1/+1
| | | | | | | | * avoid potential buffer overflows * allow SPL-build not to output "Texas Instruments Revision detection unimplemented" Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Signed-off-by: Tom Rini <trini@ti.com>
* omap4: fix boot issue on ES2.0 PandaAneesh V2012-01-16-1/+1
| | | | | | | | | | | | | Fix boot issue on ES2.0 Panda by tuning some IO settings. The CONTROL_EFUSE_2 register has to be over-ridden in software for 4430 boards. Commit 23e9f0723e48615332119de4f4ec7a833a282628 wrongly did this for CONTROL_EFUSE_1. Reverting this and doing it for CONTROL_EFUSE_2. Signed-off-by: Aneesh V <aneesh@ti.com> Tested-by: Raúl Porcel <armin76@gentoo.org>
* omap4_panda: Initialize the USB phyChris Lalancette2011-12-19-0/+63
| | | | | | | | | | During misc_init_r, make sure to setup the clocks properly for the USB hub on the pandaboard. With this in place, the USB hub and the ethernet works on the pandaboard. Signed-off-by: Chris Lalancette <clalancette@gmail.com> Acked-by: Aneesh V <aneesh@ti.com>
* omap4460: add ES1.1 identificationAneesh V2011-12-06-0/+2
| | | | Signed-off-by: Aneesh V <aneesh@ti.com>
* omap4/5: Add support for booting with CH.Sricharan2011-11-15-8/+34
| | | | | | | | | | | | | | | | Configuration header(CH) is 512 byte header attached to an OMAP boot image that will help ROM code to initialize clocks, SDRAM etc and copy U-Boot directly into SDRAM. CH can help us in by-passing SPL and directly boot U-boot, hence it's an alternative for SPL. However, we intend to support both CH and SPL for OMAP4/5. Initialization done through CH is limited and is not equivalent to that done by SPL. So U-Boot has to distinguish between the two cases and handle them accordingly. This patch takes care of doing this. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap5: emif: Add emif/ddr configurations required for omap5 evmSricharan2011-11-15-1021/+0
| | | | | | | | | | | | | Add the emif configurations required for omap5 soc.Add the correct ddr part configurations required for omap5 evm board. EDB8164B3PH from ELPIDA is the part used on the board. Also changes are done to retain some part of the code common for OMAP4/5 and keep only the remaining in the Soc specific directories. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap5: clocks: Add clocks support for omap5 platform.Sricharan2011-11-15-2/+22
| | | | | | | | | | | | Adding the correct configurations required for dplls, clocks, for omap5 Soc. Also changes are done to retain some part of the code common for OMAP4/5 and move only the remaining to the Soc specific directories. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap5: Add minimal support for omap5430.Sricharan2011-11-15-25/+16
| | | | | | | | | | | | | | | | This patch adds the minimal support for OMAP5. The platform and machine specific headers and sources updated for OMAP5430. OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture. It's a dual core SOC with GIC used for interrupt handling and SCU for cache coherency. Also moved some part of code from the basic platform support that can be made common for OMAP4/5. Rest is kept out seperately. The same approach is followed for clocks and emif support in the subsequent patches. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap: Checkpatch fixesSricharan2011-11-15-9/+2
| | | | | | | | | Fixing them here so that when the files are reused in subsequent patches for omap5, avoids new checkpatch warnings. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3 SPL: Provide weak omap_rev_stringTom Rini2011-10-27-1/+0
| | | | | | | | | We add an weak version of omap_rev_string in omap-common/spl.c and while at it drop the omap3 version. Move the prototype over to <asm/omap_common.h> with the other SPL functions. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: adding revision detection for 4460 ES1.1Ricardo Salveti de Araujo2011-10-27-0/+6
| | | | | | | Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org> 2 files changed, 17 insertions(+), 1 deletions(-) Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROLRicardo Salveti de Araujo2011-10-27-5/+5
| | | | | | | | OMAP4460 has a different set of values for the ID code, so moving the old ones to be related just with 4430. Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* mmc: omap: config VMMC, MMC1_PBIASBalaji T K2011-09-30-1/+7
| | | | | | | | | | Config VMMC voltage to 3V for MMC/SD card slot and PBIAS settings needed for OMAP4 Fixes MMC/SD detection on boot from eMMC. Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: IO settingsAneesh V2011-09-13-20/+43
| | | | | | | | Tuning some IO settings for better performance and power. And consolidate all such IO settings at one place. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: make SDRAM init work for ES1.0 siliconAneesh V2011-09-13-3/+2
| | | | | | | | | | | | SDRAM init was not working on ES1.0 due to a programming error. A pointer that was passed by value to a function was set in function emif_get_device_details(), but the effect wouldn't be seen in the calling function. The issue came out while testing for ES1.0 because ES1.0 doesn't have any SDRAM chips connected to CS1 Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: fix build warning due to signed unsigned comparisonAneesh V2011-09-04-6/+6
| | | | Signed-off-by: Aneesh V <aneesh@ti.com>
* omap: fix gpio related build breaksAneesh V2011-09-04-8/+50
| | | | | Signed-off-by: Aneesh V <aneesh@ti.com> Acked-by: Dirk Behme <dirk.behme@googlemail.com>
* omap4: clock init support for omap4460Aneesh V2011-08-03-1/+11
| | | | | Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: support TPS programmingAneesh V2011-08-03-0/+17
| | | | | | | | | | | TPS62361 is the new power supply used in OMAP4460 that supplies vdd_mpu. VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies vdd_iva. VCORE3 is not used in OMAP4460. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap: reuse omap3 gpio support in omap4Aneesh V2011-08-03-0/+34
| | | | | Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: sdram init changes for omap4460Aneesh V2011-08-03-2/+8
| | | | | Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: add omap4460 revision detectionAneesh V2011-08-03-0/+1
| | | | | Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap: add MMC and FAT support to SPLAneesh V2011-08-03-0/+8
| | | | | | | | | | | | | | - Add MMC raw and FAT mode boot support for OMAP - Provide a means by which parameters passed by ROM-code can be saved in u-boot. - Save boot mode related information passed by OMAP4 ROM-code and use it to determine where to load the u-boot from - Assumes that the image has a mkimage header. Gets the payload size and load address from this header. If the header is not detected assume u-boot.bin as payload Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap: add basic SPL supportAneesh V2011-08-03-0/+1
| | | | | | | | | | | | | - Provide alternate implementations of board_init_f() board_init_r() for OMAP spl. - Provide linker script - Initialize global data - Add serial console support - Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move it to board config header from config.mk Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: calculate EMIF register valuesAneesh V2011-08-03-6/+14
| | | | | | | | | | | | | | Calculate EMIF register values based on AC timing parameters from the SDRAM datasheet and the DDR frequency rather than using the hard-coded values. For a new board the user doen't have to go through the tedious process of calculating the register values. Instead, just provide the AC timings from the device data sheet as input and the driver will automatically calculate the register values. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: add sdram init supportAneesh V2011-08-03-4/+1036
| | | | | | | Add support for the SDRAM controller (EMIF). Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: add clock supportAneesh V2011-08-03-0/+672
| | | | | | | | | | | | | | Add support for: 1. DPLL locking 2. Initialization of clock domains and clock modules 3. Setting up the right voltage on voltage rails This work draws upon previous work done for x-loader by: Santosh Shilimkar <santosh.shilimkar@ti.com> Rajendra Nayak <rnayak@ti.com> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: add OMAP4430 revision checkAneesh V2011-08-03-8/+28
| | | | | Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: cleanup pin mux dataAneesh V2011-08-03-1/+3
| | | | | | | | | | | | | - separate mux settings into essential and non essential parts - essential part is board independent as of now(so move it to SoC directory). Will help in having single SPL for all boards. - Non-essential part(the pins not essential for u-boot to function) need to be phased out eventually. - Correct mux data by aligning to the latest settings in x-loader Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* omap4: utility function to identify the context of hw initAneesh V2011-08-03-1/+48
| | | | | | | | | | | | | | | | The basic hardware init of OMAP4(s_init()) can happen in 4 different contexts: 1. SPL running from SRAM 2. U-Boot running from FLASH 3. Non-XIP U-Boot loaded to SDRAM by SPL 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the Configuration Header feature What level of hw initialization gets done depends on this context. Add a utility function to find this context. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* armv7: adapt omap4 to the new cache maintenance frameworkAneesh V2011-07-04-1/+1
| | | | | | adapt omap4 to the new layered cache maintenance framework Signed-off-by: Aneesh V <aneesh@ti.com>
* ARMV7: OMAP: Add new mmc driver compatible with CONFIG_GENERIC_MMCSukumar Ghorai2010-10-17-0/+10
| | | | | | | | | | | | | OMAP boards currently use a legacy mmc driver. This patch adds a new mmc driver which will work with the generic mmc driver in u-boot. This new driver will work with both OMAP3 and OMAP4 boards. This patch does not remove the old driver. It should remain in the tree until all boards that use it switch to the new driver. Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> Tested-by: Steve Sakoman <steve@sakoman.com>
* ARMV7: OMAP4: Calculate SDRAM sizeAneesh V2010-09-28-0/+10
| | | | | | | | | | | Calculate the SDRAM size from DMM configuration registers instead of using hard-coded values. This gives correct values for all different boards. It's assumed that DMM sections do not overlap memory areas. Signed-off-by: Aneesh V <aneesh@ti.com> Tested-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARMV7: OMAP3: Fix broken reset command on OMAP36XX/37XX and OMAP4Steve Sakoman2010-09-08-0/+1
| | | | | | | | Using the reset command on OMAP36XX/37XX and OMAP4 caused a hang. This patch uses the reset bit appropriate for each CPU architecture. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARMV7: OMAP: Move syslib.c to omap-common since it can be shared by OMAP3 ↵Steve Sakoman2010-09-08-0/+3
| | | | | | | | | | and OMAP4 The functions in syslib.c can be shared, so this patch moves it from cpu/omap3 to cpu/omap-common Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>