summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-ls102xa
Commit message (Collapse)AuthorAgeLines
* ls102xa: fdt: Disable QSPI and DSPI in NOR/NAND/SD bootAlison Wang2015-01-23-0/+4
| | | | | | | | | | As QSPI/DSPI and IFC are pin multiplexed, QSPI and DSPI are only enabled in QSPI boot, and disabled in other boot modes. IFC is enabled in NOR/NAND/SD boot, and disabled in QSPI boot. This patch will add fdt support for the above rules. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Update snoop settings for CCI-400Alison Wang2015-01-23-0/+2
| | | | | | | | | | | CAAM is connected to CCI-400 S0 slave interface. Disable snooping for S0 will cause CAAM self test failure. This patch is to enable snooping for S0 slave interface. These CCI-400 operations are moved to board_early_init_f() to be initialized earlier. For S4 slave interface, issuing of snoop requests and DVM message requests are enabled. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add dummy gpio.h to enable CONFIG_OF_CONTROLRuchika Gupta2015-01-23-0/+15
| | | | | | | | | | | | | | | | If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled. It includes <asm/gpio.h> and then <asm/gpio.h> includes <asm/arch/gpio.h>. As a result, all the SoCs that enable CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they do not support GPIO. The right fix would be to split the lib/fdtdec.c to remove dependency on GPIO.This commit adds a dummy <asm/arch/gpio.h> to support OF_CONTROL for LS102x platform. This dummy header will be removed after FDT-GPIO stuff is fixed correctly. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ls102xa: etsec: Select ge0_clk125 for eTSEC clock muxing as defaultAlison Wang2015-01-23-0/+2
| | | | | | | | | | This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will be used via hwconfig. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm/ls1021a: Add workaround for DDR erratum A008378York Sun2015-01-23-0/+1
| | | | | | | Internal memory controller counters can reach a bad state after training in DDR4 mode if accumulated ECC or DBI mode is eanbled. Signed-off-by: York Sun <yorksun@freescale.com>
* ARM: ls102xa: Setting device's stream id for SMMUs.Xiubo Li2014-12-11-0/+17
| | | | | | | | | | | | LS1 has 4 SMMUs for address translation of the masters. All the SMMUs' stream IDs are 8-bit. The address translation depends on the stream ID of the incoming transaction. Each master has unique stream ID assigned to it and is configurable through SCFG registers. The stream ID for the masters is identical and share the same register field of STREAM ID registers. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ARM: ls102xa: allow all the peripheral access permission as R/W.Xiubo Li2014-12-11-0/+119
| | | | | | | | | | | | | | | The Central Security Unit (CSU) allows secure world software to change the default access control policies of peripherals/bus slaves, determining which bus masters may access them. This allows peripherals to be separated into distinct security domains. Combined with SMMU configuration of the system masters privileges, these features provide protection against indirect unauthorized access to data. For now we configure all the peripheral access permissions as R/W. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ls102xa: changing a few targets' configurations.Xiubo Li2014-12-11-0/+5
| | | | | | | | | Enable hypervisors utilizing the ARMv7 virtualization extension on the LS1021A-QDS/TWR boards with the A7 core tile, we add the required configuration variable. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add NAND boot support for LS1021AQDS boardAlison Wang2014-12-11-0/+7
| | | | | | | | | | | This patch adds NAND boot support for LS1021AQDS board. SPL framework is used. PBL initialize the internal RAM and copy SPL to it, then SPL initialize DDR using SPD and copy u-boot from NAND flash to DDR, finally SPL transfer control to u-boot. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add QSPI boot support for LS1021AQDS/TWR boardAlison Wang2014-12-11-0/+1
| | | | | | | | | This patch adds QSPI boot support for LS1021AQDS/TWR board. The QSPI boot image need to be programmed into the QSPI flash first. Then the booting will start from QSPI memory space. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add SD boot support for LS1021AQDS boardAlison Wang2014-12-11-0/+20
| | | | | | | | | | | This patch adds SD boot support for LS1021AQDS board. SPL framework is used. PBL initialize the internal RAM and copy SPL to it, then SPL initialize DDR using SPD and copy u-boot from SD card to DDR, finally SPL transfer control to u-boot. Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Jason Jin <jason.jin@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Update PCIe dts node statusMinghuan Lian2014-12-11-0/+3
| | | | | | | | The patch changes PCIe dts node status to 'disabled' if the corresponding controller is disabled according to serdes protocol. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: clear EPU registers for deep sleepchenhui zhao2014-12-11-0/+1
| | | | | | | | After wakeup from deep sleep, Clear EPU registers as early as possible to prevent from possible issue. It's also safe to clear at normal boot. Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Remove bit reversing for SCFG registersAlison Wang2014-11-24-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SCFG_SCFGREVCR is SCFG bit reverse register. This register must be written with 0xFFFFFFFF before writing to any other SCFG register. Then other SCFG register could be written in big-endian mode. Address: 157_0000h base + 200h offset = 157_0200h Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 W/R SCFGREV Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0-31 SCFGREV SCFG Bit Reverse Control Filed 32'h 0000_0000 - No bit reverse is applied 32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as 0:31 This patch removes the bit reversing for SCFG registers in u-boot. It will be implemented through PBI commands in RCW .pbi write 0x570200, 0xffffffff .end So other SCFG register could be written in big-endian mode in u-boot or kernel directly. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add snoop disable for slave port 0, 1 and 2Jason Jin2014-11-24-0/+1
| | | | | | | | | Disable the snoop for slave interface 0, 1 and 2 to avoid the interleaving on the CCI400 BUS. Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* drivers: usb: fsl: Define USB configs for LS102XANikhil Badola2014-11-24-0/+4
| | | | | | | | Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR, CONFIG_USB_MAX_CONTROLLER_COUNT Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Fixed a register definition errorTang Yuantian2014-11-19-1/+1
| | | | | | | There are 8 SCFG_SPARECR registers in SCFG memory block, not one. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* qe: add u-qe support to arm boardZhao Qiang2014-11-19-0/+4
| | | | | | | | | ls1021 is arm-core and support qe which is u-qe. add u-qe init for arm board. Signed-off-by: Zhao Qiang <B45475@freescale.com> [York Sun: Fix compiling error caused by u_qe_init()] Reviewed-by: York Sun <yorksun@freescale.com>
* ls102x: configs - Add hash command in freescale LS1 platformsRuchika Gupta2014-10-16-0/+4
| | | | | | | | | Hardware accelerated support for SHA-1 and SHA-256 has been added. Hash command enabled along with hardware accelerated support for SHA-1 and SHA-256 for platforms which have CAAM block. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/ls1021aqds: Add DDR4 supportYork Sun2014-09-25-0/+5
| | | | | | | | | | | LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig for this variant to enable DDR4 support. RAW timing parameters are not added for DDR4. The board timing parameters are only tuned for single- rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM availability. Signed-off-by: York Sun <yorksun@freescale.com> CC: Alison Wang <alison.wang@freescale.com>
* video: dcu: Add DCU driver supportWang Huan2014-09-08-0/+4
| | | | | | | | | This patch is to add DCU driver support. DCU also named 2D-ACE(Two Dimensional Animation and Compositing Engine) is a system master that fetches graphics stored in internal or external memory and displays them on a TFT LCD panel. Signed-off-by: Alison Wang <alison.wang@freescale.com>
* arm: ls102xa: Add Freescale LS102xA SoC supportWang Huan2014-09-08-0/+676
The QorIQ LS1 family is built on Layerscape architecture, the industry's first software-aware, core-agnostic networking architecture to offer unprecedented efficiency and scale. Freescale LS102xA is a set of SoCs combines two ARM Cortex-A7 cores that have been optimized for high reliability and pack the highest level of integration available for sub-3 W embedded communications processors with Layerscape architecture and with a comprehensive enablement model focused on ease of programmability. Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Jason Jin <jason.jin@freescale.com> Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>