summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-fsl-lsch3
Commit message (Collapse)AuthorAgeLines
* armv8/lsch3/config: Define USB XHCI controller base address for LS2085ANikhil Badola2015-08-03-0/+3
| | | | | | | | Define base address of both usb xhci controllers in lsch3 config in the format (IMMR + offset) for LS2085A Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/lsch3/config: Define CONFIG_SYS_CACHELINE_SIZE for LS2085ANikhil Badola2015-08-03-0/+1
| | | | | | | | Define CONFIG_SYS_CACHELINE_SIZE for LS2085A which is required by USB XHCI stack for alignment Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls2085aqds: DSPI pin muxing configure through QIXISHaikun Wang2015-07-20-0/+2
| | | | | | | | | | | | | DSPI has pin muxing with SDHC and other IPs, this patch check the value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check the "hwconfig" variable. If those pins are configured to DSPI and "hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure the routing to on-board SPI memory. Otherwise will configure to SDHC. DSPI is enabled in "hwconfig" by appending "dspi", eg. setenv hwconfig "$hwconfig;dspi" Signed-off-by: Haikun Wang <haikun.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls2085a: Enable DSPI get input clk form 'mxc_get_clock'Haikun Wang2015-07-20-0/+1
| | | | | Signed-off-by: Haikun Wang <haikun.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/fsl-lsch3: device tree fixups for PCI stream IDsStuart Yoder2015-07-20-0/+10
| | | | | | | | | | | This patch adds the infrastructure to update device tree nodes to convey SMMU stream IDs in the device tree. Fixups are implemented for PCI controllers initially. Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/fsl-lsch3: partition stream IDsStuart Yoder2015-07-20-0/+64
| | | | | | | | | | | | Stream IDs on ls2085a devices are not hardwired and are programmed by sw. There are a limited number of stream IDs available, and the partitioning of them is scenario dependent. This header defines the partitioning between legacy, PCI, and DPAA2 devices. Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/fsl-ch3: Add support to print SoC personalityPrabhakar Kushwaha2015-07-20-0/+20
| | | | | | | | | | | This patch adds support to print out the SoC personality. Freescale LS20xx SoCs (compliant to Chassis-3 specifications) can have 6 personalities: LS2045AE, LS2045A, LS2080AE, LS2080A, LS2085AE and LS2085A Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ls2085a: esdhc: Add esdhc support for ls2085aYangbo Lu2015-04-23-0/+2
| | | | | | | This patch adds esdhc support for ls2085a. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
* armv8/ls2085aqds: NAND boot supportScott Wood2015-04-23-0/+9
| | | | | | | | | This adds NAND boot support for LS2085AQDS, using SPL framework. Details of forming NAND image can be found in README. Signed-off-by: Scott Wood <scottwood@freescale.com> [York Sun: Remove +S from defconfig after commit 252ed872] Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ldpaa: Add support of WRIOP static data structurePrabhakar Kushwaha2015-04-23-0/+27
| | | | | | | | | | | | Wire rate IO Processor (WRIOP) provide support of receive and transmit ethernet frames from the ethernet MAC. Here Each WRIOP block supports upto 64 DPMACs. Create a house keeping data structure to support upto 16 DPMACs and store external phy related information. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
* net/memac_phy: reuse driver for little endian SoCsShaohui Xie2015-04-23-0/+1
| | | | | | | | | | | | | The memac for PHY management on little endian SoCs is similar on big endian SoCs, so we modify the driver by using I/O accessor function to handle the endianness, so the driver can be reused on little endian SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access is little endian, if not, the I/O access is big endian. Move fsl_memac.h out of powerpc include. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
* armv8: Add SerDes framework for Layerscape ArchitectureMinghuan Lian2015-04-23-0/+76
| | | | | | | | | | | Add support of SerDes framework for Layerscape Architecture. - Add support of 2 SerDes block - Add SerDes protocol parsing and detection - Create table of SerDes protocol supported by LS2085A Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls2085a: Add workaround for USB erratum A-008751Scott Wood2015-04-23-0/+5
| | | | | | | | Without this "USB may not work" according to the erratum text, though I did not notice a problem without it. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
* fsl-lsch3: Introduce place for common early SoC initScott Wood2015-04-23-0/+8
| | | | | Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
* armv8/fsl-lsch3: Set nodes in DVM domainScott Wood2015-04-23-0/+6
| | | | | | | This is required for TLB invalidation broadcasts to work. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
* armv8/ls2085a: Update common header filePrabhakar Kushwaha2015-04-23-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ls2085a_common.h contains hard-coded information for NOR/NAND flash, I2C, DDR, etc. These are platform specific. Move them out of common header file and placed into respective board header files. Move TEXTBASE to 1MB offset to fit NOR flash with up to 1MB sector size. Enable command auto complete. Update prompt symbol. Set fdt_high to 0xa0000000 because Linux requires that the fdt be 8-byte aligned and below 512 MiB. Besides ensuring compliance with the 512 MiB limit, this avoids problems with the dtb being misaligned within the FIT image. Change the MC FW, MC DPL and Debug server NOR addresses in compliance with the NOR flash layouts for 128MB flash. Add PCIe macros. Enable "loadb" command. Disable debug server. Enable workaround for erratum A008511. Stop reset on panic for postmortem debugging. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
* armv8/fsl-lsch3: Implement workaround for erratum A008585York Sun2015-04-23-0/+1
| | | | | | | Generic Timer may contain an erroneous value. The workaround is to read it twice until getting the same value. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ldpaa_eth: Add LDPAA Ethernet driverPrabhakar Kushwaha2015-04-23-0/+6
| | | | | | | | | | | | | | | LDPAA Ethernet driver is a freescale's new ethernet driver based on Layerscape architecture. Every ethernet driver controls on DPNI object. Where all DPNIs share one common DPBP and DPIO object to support Rx and Tx flows. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> CC: Cristian Sovaiala <cristian.sovaiala@freescale.com> CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com> CC: J. German Rivera <German.Rivera@freescale.com> [York Sun: s/NetReceive/net_process_received_packet] Reviewed-by: York Sun <yorksun@freescale.com>
* driver/fsl-mc: Add support of MC FlibsPrabhakar Kushwaha2015-04-21-0/+2
| | | | | | | | | | | | | | | | | | | | | | Freescale's Layerscape Management Complex (MC) provide support various objects like DPRC, DPNI, DPBP and DPIO. Where: DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO DPBP: Management of buffer pool DPIO: Used for used to QBMan portal DPNI: Represents standard network interface These objects are used for DPAA ethernet drivers. Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com> Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com> Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/fsl-lsch3: Add Freescale Debug Server driverBhupesh Sharma2015-04-21-1/+9
| | | | | | | | | | | | | The Debug Server driver is responsible for loading the Debug server FW on the Service Processor (Cortex-A5 core) on LS2085A like SoCs and then polling for the successful initialization of the same. TOP MEM HIDE is adjusted to ensure the space required by Debug Server FW is accounted for. MC uses the DDR area which is calculated as: MC DDR region start = Top of DDR - area reserved by Debug Server FW Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/fsl-lsch3: Enable erratum workround for A008514York Sun2015-02-24-0/+1
| | | | | | Erratum A008514 appleis to ls2085a. Signed-off-by: York Sun <yorksun@freescale.com>
* armv8/fsl-lsch3: Enable workaround for A008336York Sun2015-02-24-0/+4
| | | | | | Erratum A008336 applied to LS2085A. Signed-off-by: York Sun <yorksun@freescale.com>
* armv8/fsl-lsch3: Add support for second DDR clockYork Sun2015-02-24-0/+3
| | | | | | | | FSL-LSCH3 platforms can have multiple DDR clocks. LS2085A has one clock for general DDR controlers, and another clock for DP-DDR. DDR driver needs to change to support multiple clocks. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Add workaround for A008336York Sun2015-02-24-0/+5
| | | | | | | Erratum A008336 requires setting EDDRTQCR1[2] in DDRC DCSR space for 64-bit DDR controllers. Signed-off-by: York Sun <yorksun@freescale.com>
* fsl-ch3/lowlevel: TZPC and TZASC programming to configure non-secure accessesBhupesh Sharma2015-02-24-0/+28
| | | | | | | | | | | | | This patch ensures that the TZPC (BP147) and TZASC-400 programming happens for LS2085A SoC only when the desired config flags are enabled and ensures that the TZPC programming is done to allow Non-secure (NS) + secure (S) transactions only for DCGF registers. The TZASC component is not present on LS2085A-Rev1, so the TZASC-400 config flag is turned OFF for now. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/fsl-lsch3: Release secondary cores from boot hold off with Boot PageYork Sun2014-09-25-1/+37
| | | | | | | | | | Secondary cores need to be released from holdoff by boot release registers. With GPP bootrom, they can boot from main memory directly. Individual spin table is used for each core. Spin table and the boot page is reserved in device tree so OS won't overwrite. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
* ARMv8/ls2085a_emu: Enable DP-DDR as standalone memory blockYork Sun2014-09-25-1/+2
| | | | | | | DP-DDR is used for DPAA, separated from main memory pool for general use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit). Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr: Fix DDR4 driver for ARMYork Sun2014-07-22-0/+4
| | | | | | | Previously the driver was only tested on Power SoCs. Different barrier instructions are needed for ARM SoCs. Signed-off-by: York Sun <yorksun@freescale.com>
* ARMv8/ls2085a_emu: Add LS2085A emulator and simulator board supportYork Sun2014-07-04-1/+1
| | | | | | | | | | | | | | | | LS2085A is an ARMv8 implementation. This adds board support for emulator and simulator: Two DDR controllers UART2 is used as the console IFC timing is tightened for speedy booting Support DDR3 and DDR4 as separated targets Management Complex (MC) is enabled Support for GIC 500 (based on GICv3 arch) Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Arnab Basu <arnab.basu@freescale.com> Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
* ARMv8/FSL_LSCH3: Add FSL_LSCH3 SoCYork Sun2014-07-03-0/+226
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with ARMv8 cores and 3rd generation of Chassis. We use different MMU setup to support memory map and cache attribute for these SoCs. MMU and cache are enabled very early to bootst performance, especially for early development on emulators. After u-boot relocates to DDR, a new MMU table with QBMan cache access is created in DDR. SMMU pagesize is set in SMMU_sACR register. Both DDR3 and DDR4 are supported. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com> Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
generated by cgit v1.1 at 2024-11-07 06:43:35 +0000