summaryrefslogtreecommitdiff
path: root/arch/arm/dts
Commit message (Collapse)AuthorAgeLines
* ARM: dts: uniphier: add UniPhier specific compatible to eMMC nodeMasahiro Yamada2017-01-17-4/+2
| | | | | | | The "cdns,sd4hc" is a fallback of the IP. Add the SoC-specific compatible string. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* sunxi: dts: OrangePi Zero: add Ethernet nodeAndre Przywara2017-01-15-0/+11
| | | | | | | | | | | The OrangePi Zero can happily use the EMAC along with its integrated PHY to use Ethernet (for TFTP booting, for instance). Add the emac node to the board .dts by copying it from the OrangePi One DT. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* sunxi: add proper device tree for Orange Pi Zero boardsIcenowy Zheng2017-01-15-0/+144
| | | | | | | | Add a proper device tree file for Orange Pi Zero boards from Xunlong, which come with a Allwinner H2+ SoC (similar to H3). Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz> Reviewed-by: Jagan Teki <jagan@openedev.com>
* sunxi: enable H3 EMAC for the nanopi neoJelle van der Waa2017-01-15-0/+11
| | | | | | | | | The nanopi already had the CONFIG_SUN8I_EMAC=y enabled in it's defconfig file, but was missing the &emac the device tree entry. Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* dts: arm64: rk3399: add max-frequency for sdhciKever Yang2017-01-11-0/+1
| | | | | | | Add 'max-frequency' for sdhci node for clock init. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* rockchip: dts: popmetal: add usb host power supply nodeKever Yang2017-01-11-0/+23
| | | | | | | | | | | The popmetal board using a HOST_VBUS_DRV gpio signal to control the USB host port 5V power, add a fix regulator and pinctrl for it, and enable the USB host1 controller with the vbus-supply. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Added rockchip: tag: Signed-off-by: Simon Glass <sjg@chromium.org>
* ARM64: zynqmp: Fix i2c node's compatible stringMoritz Fischer2017-01-10-2/+2
| | | | | | | | | | | The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core which fixes some silicon bugs that needed software workarounds in Version 1.0 that was used on Zynq systems. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Add idle state for ZynqMPStefan Krsmanovic2017-01-10-0/+17
| | | | | | | | | | | | Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0 idle state is added in this patch. References to the idle-states node are added in all CPU nodes. Time values: entry/exit latencies and min-residency, needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0 and Extended StateID format. Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com> Acked-by: Will Wong <willw@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Fix usb nodes for dc1 and dc2Michal Simek2017-01-10-0/+8
| | | | | | | Fix DT binding for usb nodes. Setup correct aliases and enable dwc3 nodes. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM64: zynqmp: Add missing earlycon for ep108Michal Simek2017-01-10-0/+1
| | | | | | | Just sync between version. Others zynqmp boards have this setup. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* ARM64: zynqmp: clk: Add the clock for watchdogShubhrajyoti Datta2017-01-10-0/+4
| | | | | | | | | | | The watchdog clock node is missing. Add the same. This solves the below error. cdns-wdt fd4d0000.watchdog: input clock not found cdns-wdt: probe of fd4d0000.watchdog failed with error -2 Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source propertySudeep Holla2017-01-10-2/+2
| | | | | | | | | | | | | | | | Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: zynq: Remove spi-max-frequencyMichal Simek2017-01-10-2/+0
| | | | | | | spi-max-frequency for spi bus depends on devices which are connected to it. Remove this parameter from dtsi file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: dts: tegra: Sync paz00 with Linux 4.8Misha Komarovskiy2017-01-03-29/+568
| | | | | | | | | | | | | | | Sync with Linux 4.8 dts plus vdd_bl regulator to fix backlight start, display timings and USB controller aliases fix. Signed-off-by: Misha Komarovskiy <zombah@gmail.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Warren <twarren@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* colibri_t20: fix ulpi reset polarityMarcel Ziswiler2017-01-03-2/+4
| | | | | | | | | | | | | | | | Fix ULPI reset polarity which caused a hard hang on Colibri T20 upon attempting to start the USB subsystem: This fixes my late commit d5a24d8b53d350364bd429b7104ec369b817e4b8 (colibri_t20: fix usb operation and controller order) inadvertently having overwritten Stephen's previous commit 2f6a7e8ce5df8b99d84bfd486c6f99d92322ce04 (ARM: tegra: fix USB ULPI PHY reset signal inversion confusion). While at it also fix comment about on-module USB port. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* apalis_t30: comment about disabled pcie nodesMarcel Ziswiler2017-01-03-0/+2
| | | | | | | Add a comment about the disabled PCIe port nodes. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* arm: dts: s5pc1xx-goni: add the pmic node for using DMJaehoon Chung2016-12-22-0/+165
| | | | | | | | To use driver-model adds the pmic node for max8998. This is used as kerel device-tree in Linux. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini2016-12-20-2/+3
|\
| * ARM64: zynqmp: Add one empty line between license and nodesMichal Simek2016-12-20-0/+1
| | | | | | | | | | | | Sync with Linux kernel. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * ARM: dt: zynq: Add labels to cpu nodes to allow overriding OPPs.Moritz Fischer2016-12-20-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | By adding labels to the cpu nodes in the dtsi, a dts that includes it can change the OPPs by referencing the cpu0 through the label. [Based on linux (400b6a0cbef55d1ae32808eaa1ef1c28820bf6ac)] Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: u-boot@lists.denx.de Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | Merge git://git.denx.de/u-boot-dmTom Rini2016-12-20-4/+37
|\ \ | |/ |/|
| * sunxi: Use binman for sunxi boardsSimon Glass2016-12-20-0/+14
| | | | | | | | | | | | | | | | Move sunxi boards to use binman. This involves adding the image definition to the device tree and using it in the Makefile. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
| * tegra: Use a U-Boot-specific .dtsi fileSimon Glass2016-12-20-4/+23
| | | | | | | | | | | | | | | | With the new device-tree rules it is possible to put device-tree changes needed by U-Boot into their own file. As an example of this approach, move Tegra over to use it. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-12-18-1/+5444
|\ \ | |/ |/| | | | | | | Migrate CONFIG_ARCH_USE_MEMSET/MEMCPY with this merge. Signed-off-by: Tom Rini <trini@konsulko.com>
| * arm: dts: imx6qdl-icore-rqs: Add FEC nodeJagan Teki2016-12-16-0/+46
| | | | | | | | | | | | | | | | | | Add FEC node for Engicam i.CoreM6 RQS modules. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: dts: imx6ul-geam: Add FEC nodeJagan Teki2016-12-16-0/+21
| | | | | | | | | | | | | | | | | | Add FEC node for Engicam GEAM6UL module. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: dts: imx6qdl-icore-rqs: Add I2C node'sJagan Teki2016-12-16-0/+41
| | | | | | | | | | | | | | | | | | Add I2C nodes for Engicam i.CoreM6 RQS modules. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6q: Add Engicam i.CoreM6 Solo/Duallite RQS Starter Kit initial supportJagan Teki2016-12-16-0/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07 +0530) CPU: Freescale i.MX6DL rev1.3 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 DualLite/Solo RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial supportJagan Teki2016-12-16-0/+134
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: dts: imx6ul-geam: Add I2C nodesJagan Teki2016-12-16-0/+28
| | | | | | | | | | | | | | | | | | Add I2C nodes for Engicam GEAM6UL module. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial supportJagan Teki2016-12-16-1/+121
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot Log: -------- U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30) Trying to boot from MMC1 U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Engicam GEAM6UL DRAM: 128 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 geam6ul> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: dts: Add devicetree for i.MX6ULJagan Teki2016-12-16-0/+942
| | | | | | | | | | | | | | | | | | | | | | | | | | Add i.MX6UL dtsi support from Linux. Here is the last commit: "ARM: dts: add gpio-ranges property to iMX GPIO controllers" (sha1: bb728d662bed0fe91b152550e640cb3f6caa972c) Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * ARM: dts: imx6qdl-icore: Add FEC supportJagan Teki2016-12-16-0/+24
| | | | | | | | | | | | | | | | | | | | Add FEC dts support for Engicam i.CoreM6 dql modules. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx: add i.MX53 Beckhoff CX9020 Embedded PCPatrick Bruenn2016-12-16-0/+1491
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
| * arm: imx: add i.MX6SLL EVK board supportPeng Fan2016-12-16-0/+802
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add i.MX6SLL EVK board support. 1. Add imx6sll-evk device tree. 2. Enable SDHC/I2C/UART. 3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver. Boot Log: U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800) CPU: Freescale i.MX6SLL rev1.0 at 792MHz CPU: Commercial temperature grade (0C to 95C)Reset cause: POR Model: Freescale i.MX6SLL EVK Board Board: MX6SLL EVK DRAM: 2 GiB i2c bus 0 at 35258368, no gpio pinctrl state. PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * arm: dts: add i.MX6SLL device treePeng Fan2016-12-16-0/+1741
| | | | | | | | | | | | | | Add i.MX6SLL device tree. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * ARM: dts: vf: Fix warning about missing reg propertyStefan Agner2016-12-16-0/+2
| | | | | | | | | | | | | | | | | | Add proper reg values for the two AIPS bus nodes. This avoids this two warnings: Node /soc/aips-bus@40000000 has a unit name, but no reg property Node /soc/aips-bus@40080000 has a unit name, but no reg property Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini2016-12-16-1/+1
|\ \
| * | ARM: dts: am437x-idk: Fix QSPI compatible stringVignesh R2016-12-15-1/+1
| |/ | | | | | | | | | | | | | | | | | | Unlike Linux kernel, U-Boot depends on "spi-flash" compatible to probe m25p80 spi-nor devices. Hence, add "spi-flash" compatible string to m25p80 node. Without this patch, flash device DT data is not parsed and QSPI operates in unsupported mode leading to data corruption. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* | armv8: ls1043a: dts: Fix the ranges table of IFC nodeHou Zhiqiang2016-12-15-8/+8
| | | | | | | | | | | | | | Corrected the ranges table of the IFC node. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | armv8: ls1043ardb: dts: Fix the unit-address of some I2C device nodesHou Zhiqiang2016-12-15-2/+2
|/ | | | | | | The unit-address should be the same as the I2C address of the device. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* Merge git://www.denx.de/git/u-boot-marvellTom Rini2016-12-12-64/+183
|\
| * arm64: mvebu: Add pin control nodes to A8K family DTS filesKonstantin Porotchkin2016-12-12-0/+161
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add pin control nodes to APN806, CP-master, CP-slave and Armada-7040 and Armada-8040 boards DTS files Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * arm64: mvebu: Modify the A8K SPI and I2C config in DTSKonstantin Porotchkin2016-12-12-67/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Align the Armada-8040-db and Armada-7040-db SPI and I2C DTS settings with latest DB settings: - 8040-db: disable i2c0 and spi0 on AP (MPPs are reserved for SDIO) - 8040-db: disable cps_i2c0 on CP1 - 8040-db: enable spi1 on CP1 (the new location of the boot flash) The spi1 on CP1 is aliased as spi0 since this is the way the driver enumerates it. Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
* | ARM: dts: uniphier: sync Device Tree with LinuxMasahiro Yamada2016-12-11-1851/+2684
|/ | | | | | Sync with the latest kernel. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* socfpga: add support for Terasic DE1-SoC boardAnatolij Gustschin2016-12-06-0/+67
| | | | | | | | Add CycloneV based Terasic DE1-SoC board. The board boots from SD/MMC. Ethernet and USB host is supported. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Marek Vasut <marex@denx.de>
* ls1021a: QSPI: update the node for QSPI supportYuan Yao2016-12-05-0/+1
| | | | | | | | | Add the name for register space and memory space. <0x1550000 0x10000 > is the QSPI register space. <0x40000000 0x4000000> is the QSPI memory space. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* arm64: mvebu: armada-8040-db.dts: Add I2C and SPI aliasesStefan Roese2016-12-05-0/+5
| | | | | | | | | | | | | | | Add I2C and SPI aliases to enable usage in U-Boot. Otherwise U-Boot will not be able to use the SPI NOR chip for environment storage and use "i2c dev 0" to select this I2C bus. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com>
* arm64: mvebu: armada-8040-db.dts: Add COMPHY configurationStefan Roese2016-12-05-0/+84
| | | | | | | | | | | | | | This patch adds the COMPHY device tree configuration to the DT file for the Marvell DB-88F8040 devel board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com>
* arm64: mvebu: armada-cp110-slave.dtsi: Add COMPHY / UTMI device tree nodesStefan Roese2016-12-05-0/+19
| | | | | | | | | | | | | | This patch adds the COMPHY and UTMI device tree nodes to the cp110-slave dtsi file for the Armada 8K. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Omri Itach <omrii@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Cc: Hanna Hawa <hannah@marvell.com>
generated by cgit v1.1 at 2024-11-14 22:25:34 +0000