summaryrefslogtreecommitdiff
path: root/arch/arm/cpu
Commit message (Collapse)AuthorAgeLines
...
* OMAP5: io: Configure the io settings for omap5430 sevm board.SRICHARAN R2012-05-15-0/+83
| | | | | | | | | The control module provides options to set various signal integrity parameters like the output impedance, slew rate, load capacitance for different pad groups. Configure these as required for the omap5430 sevm board. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP5: clocks: Change clock settings as required for ES1.0 silicon.SRICHARAN R2012-05-15-36/+78
| | | | | | | | Aligning all the clock related settings like the dpll frequencies, their respective clock outputs, etc to the ideal values recommended for OMAP5430 ES1.0 silicon. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP4: scale voltage of core before MPU scalesNishanth Menon2012-05-15-28/+35
| | | | | | | | | | | | | | | | OMAP4 requires that parent domains scale ahead of dependent domains. This is due to the restrictions in timing closure. To ensure a consistent behavior across all OMAP4 SoC, ensure that vdd_core scale first, then vdd_mpu and finally vdd_iva. As part of doing this refactor the logic to allow for future addition of OMAP4470 without much ado. OMAP4470 uses different SMPS addresses and cannot be introduced in the current code without major rewrite. Reported-by: Isabelle Gros <i-gros@ti.com> Reported-by: Jerome Angeloni <j-angeloni@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* OMAP4460: TPS Ensure SET1 is selected after voltage configurationNishanth Menon2012-05-15-3/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms. Currently we control this pin with a mux configuration as part of boot sequence. Current configuration results in the following voltage waveform: |---------------| (SET1 default 1.4V) | --------(programmed voltage) | <- (This switch happens on mux7,pullup) vdd_mpu(TPS) -----/ (OPP boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -----------------------/ (OPP boot voltage) Problem 1) |<----- Tx ------>| timing violation for a duration Tx close to few milliseconds. Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP. By using GPIO as recommended as standard procedure by TI, the sequence changes to: -------- (programmed voltage) vdd_mpu(TPS) ------------/ (Opp boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -------------/ (OPP boot voltage) NOTE: This does not attempt to address OMAP5 - Aneesh please confirm Reported-by: Isabelle Gros <i-gros@ti.com> Reported-by: Jerome Angeloni <j-angeloni@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* OMAP3+: Introduce generic logic for OMAP voltage controllerNishanth Menon2012-05-15-45/+146
| | | | | | | | | | | | | | | | | | | | OMAP Voltage controller is used to generically talk to PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code in multiple SoC code, introduce a common voltage controller logic which can be re-used from elsewhere. With this change, we replace setup_sri2c with omap_vc_init which has the same functionality, and replace the voltage scale replication in do_scale_vcore and do_scale_tps62361 with omap_vc_bypass_send_value. omap_vc_bypass_send_value can also now be used with any configuration of PMIC. NOTE: Voltage controller controlling I2C_SR is a write-only data path, so no register read operation can be implemented. Reported-by: Isabelle Gros <i-gros@ti.com> Reported-by: Jerome Angeloni <j-angeloni@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM:OMAP+:MMC: Add parameters to MMC initJonathan Solnit2012-05-15-3/+3
| | | | | | | | | | Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
* arm926ejs: add NXP LPC32x0 cpu series supportVladimir Zapolskiy2012-05-15-0/+379
| | | | | | | | This change adds initial support for NXP LPC32x0 SoC series. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZEMarek Vasut2012-04-19-1/+1
| | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: scottwood@freescale.com
* ARM926EJS: Fix cache.c to comply with checkpatch.plMarek Vasut2012-04-16-9/+8
| | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* ARM926EJS: Make asm routines volatile in cache opsMarek Vasut2012-04-16-1/+1
| | | | | | | | | | We certainly don't want the compiler to reorganise the code for dcache flushing. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Stefano Babic <sbabic@denx.de>
* ARM1136: MX35: Make asm routines volatile in cache opsStefano Babic2012-04-16-10/+12
| | | | | | | | | | As well as pushed for ARM926EJS, we certainly don't want the compiler to reorganise the code for dcache flushing Fix checkpatch warnings as well. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Marek Vasut <marex@denx.de> CC: Albert Aribaud <albert.u.boot@aribaud.net>
* ARM: add u-boot.imx as target for i.MX SOCsStefano Babic2012-04-16-0/+3
| | | | | | | | | | | | | | | Freescale SOCs require an header to u-boot.bin The patch adds u-boot.imx to the default targets if the imx file is set (IMX_CONFIG). Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> CC: Loïc Minier <loic.minier@linaro.org> CC: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Tested-by: Dirk Behme <dirk.behme@googlemail.com>
* DMA: Split the APBH DMA init into block and channel initMarek Vasut2012-04-16-0/+6
| | | | | | | | | | | | | | | | | | | | | | | This fixes the issue where mxs_dma_init() was called either twice or never, without introducing any new init hooks. The idea is to allow each and every device using the APBH DMA block to configure and request only the channels it uses, instead of making it call init for all the channels as is now. The common DMA block init part, which only configures the block, is then called from CPUs arch_cpu_init() call. NOTE: This patch depends on: http://patchwork.ozlabs.org/patch/150957/ Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* ARM: 926ejs: use debug() for misaligned addressesStefano Babic2012-04-16-1/+1
| | | | | | | | | | | | Misaligned warnings are useful to debug faulty drivers. A misaligned warning is printed also when the driver is correct - use debug() instead of printf(). Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Albert Aribaud <albert.u.boot@aribaud.net> CC: Mike Frysinger <vapier@gentoo.org> CC: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
* ARM1136: add cache flush and invalidate operationsAnatolij Gustschin2012-04-16-0/+95
| | | | | | | | | | | | | | | | | | Since commit 5c1ad3e6f8ae578bbe30e09652f1531e9bc22031 (net: fec_mxc: allow use with cache enabled) the FEC_MXC driver uses flush_dcache_range() and invalidate_dcache_range() functions. This driver is also configured for ARM1136 based 'flea3' and 'mx35pdk' boards which currently do not build as there are no ARM1136 specific flush_dcache_range() and invalidate_dcache_range() functions. Add various ARM1136 cache functions to fix building for 'flea3' and 'mx35pdk'. Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> CC: Mike Frysinger <vapier@gentoo.org> CC: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
* i.MX6: implement enable_caches()Eric Nelson2012-04-16-0/+8
| | | | | | | disabled by default until drivers are fixed Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
* arm: Use common .lds file where possibleSimon Glass2012-03-30-1071/+0
| | | | | | | | | | Each cpu directory currently has its own .lds file. This is only needed in most cases because the start.o file is in a different subdir. Now that we can factor out this difference, we can move most cpus over to the common .lds file. Signed-off-by: Simon Glass <sjg@chromium.org>
* arm: add a common .lds link scriptSimon Glass2012-03-30-0/+94
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Most ARM CPUs use a very similar link script. This adds a basic script that can be used by most CPUs. Two new symbols are introduced which are intended to eventually be defined on all architectures to make things easier for generic relocation and reduce special-case code for each architecture: __image_copy_start is the start of the text area (equivalent to the existing _start on ARM). It marks the start of the region which must be copied to a new location during relocation. This symbol is called __text_start on x86 and microblaze. __image_copy_end is the end of the region which must be copied to a new location during relocation. It is normally equal to the start of the BSS region, but this can vary in some cases (SPL?). Making this an explicit symbol on its own removes any ambiguity and permits common code to always do the right thing. This new script makes use of CPUDIR, now defined by both Makefile and spl/Makefile, to find the directory containing the start.o object file, which is always placed first in the image. To permit MMU setup prior to relocation (as used by pxa) we add an area to the link script which contains space for this. This is taken from commit 7f4cfcf. CPUs can put the contents in there using their start.S file. BTW, shouldn't that area be 16KB-aligned? Signed-off-by: Simon Glass <sjg@chromium.org>
* arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warningsAnatolij Gustschin2012-03-29-3/+1
| | | | | | | | | | | | | Fix: clocks-common.c: In function 'setup_non_essential_dplls': clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used [-Wunused-but-set-variable] clocks-common.c: In function 'setup_non_essential_dplls': clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Tom Rini <trini@ti.com>
* sdrc.c: Fix typo in do_sdrc_init() for SPLTom Rini2012-03-29-1/+1
| | | | | | We need to setup CS0 and CS1 not CS0 and CS0 again. Signed-off-by: Tom Rini <trini@ti.com>
* tegra: Enhance clock support to handle 16-bit clock divisorsSimon Glass2012-03-29-22/+41
| | | | | | | | I2C ports have a 16-bit clock divisor. Add code to handle this special case so that I2C speeds below 150KHz are supported. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASESimon Glass2012-03-29-6/+6
| | | | | | | | | Change this name to fit with the current convention in the Tegra header file. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: usb: Add support for Tegra USB peripheralSimon Glass2012-03-29-1/+463
| | | | | | | | | | | | | | | | | | This adds basic support for the Tegra2 USB controller. Board files should call board_usb_init() to set things up. Configuration is performed through the FDT, with aliases used to set the order of the ports, like this fragment: aliases { /* This defines the order of our USB ports */ usb0 = "/usb@0xc5008000"; usb1 = "/usb@0xc5000000"; }; drivers/usb/host files ONLY: Acked-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: fdt: Add function to return peripheral/clock IDSimon Glass2012-03-29-0/+58
| | | | | | | | | A common requirement is to find the clock ID for a peripheral. This is the second cell of the 'clocks' property (the first being the phandle itself). Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: fdt: Add Tegra2x device tree file from kernelSimon Glass2012-03-29-0/+2
| | | | | | | | | | | | | This was taken from commit b48c54e2 at: git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git config.mk is updated to provide this file to boards through the built-in mechanism: /include/ ARCH_CPU_DTS Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer loadTom Warren2012-03-29-5/+5
| | | | | | | | | | | | | The 4.2.2 gcc in the ELDK42 release doesn't like the direct SP load using a constant in tegra2_start. Change it to use a load thru another reg using mov sp, %0 : : "r"(CONST). Tested on my Seaboard T20-A03, U-Boot loads and runs OK. Also compiled all tegra2 builds with both gcc 4.2.2 and 4.4.1 OK. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* i.MX28: Enable caches by defaultMarek Vasut2012-03-29-0/+10
| | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* ARM926EJS: Implement cache operationsMarek Vasut2012-03-29-12/+54
| | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* nhk8815: fix build errorsAnatolij Gustschin2012-03-28-0/+10
| | | | | | | | | | | | | Fix: common/libcommon.o: In function `cread_line': /home/ag/git/u-boot/common/main.c:695: undefined reference to `get_ticks' /home/ag/git/u-boot/common/main.c:695: undefined reference to `get_tbclk' /home/ag/git/u-boot/common/main.c:698: undefined reference to `get_ticks' Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Alessandro Rubini <rubini@unipv.it> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Alessandro Rubini <rubini@unipv.it>
* ARM: highbank: add reset supportRob Herring2012-03-28-0/+1
| | | | | | | Implement reset for highbank platform. Reset is triggered via a wfi instruction, so enabling armv7 for the compiler is necessary. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* ARM: highbank: Add boot counter supportRob Herring2012-03-28-1/+37
| | | | | | Add boot counter support using an sysreg which is persistent across reset. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* ARM: highbank: fix us_to_tick calculationRob Herring2012-03-28-2/+2
| | | | | | | udelay calls were off due to failing to convert us to ns. Fix this and drop the unnecessary shifts since NS_PER_TICK is only 7ns. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* ARM: highbank: add missing get_tbclkRob Herring2012-03-28-0/+5
| | | | | | | The get_tbclk function was missing and the recent commit "common: add possibility for readline_into_buffer timeout" makes it required. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* ARM: fix s3c2410 timer codeDavid Müller (ELSOFT AG)2012-03-27-44/+20
| | | | | | | | This patch fixes the s3c24x0 timer code to work with the ARM relocation feature. Signed-off-by: David Mueller <d.mueller@elsoft.ch> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* SPL: call cleanup_before_linux() before booting LinuxStefano Babic2012-03-27-1/+1
| | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Simon Schwarz <simonschwarzcor@gmail.com>
* OMAP3: SPL: do not call I2C init if no I2C is set.Stefano Babic2012-03-27-0/+2
| | | | | | | | | | Call i2c initialization in spl_board_init only if I2C is configured for the board. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Simon Schwarz <simonschwarzcor@gmail.com>
* Add cache functions to SPL for armv7Stefano Babic2012-03-27-2/+2
| | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Simon Schwarz <simonschwarzcor@gmail.com>
* omap/spl: change output of spl_parse_image_headerSimon Schwarz2012-03-27-1/+1
| | | | | | | | | This only outputs "Assuming u-boot.bin..." if debug is active. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* omap-common/spl: Add linux boot to SPLSimon Schwarz2012-03-27-23/+74
| | | | | | | | | | | | | | | | | | | | | | | | This adds Linux booting to the SPL This depends on CONFIG_MACH_TYPE patch by Igor Grinberg (http://article.gmane.org/gmane.comp.boot-loaders.u-boot/105809) Related CONFIGs: CONFIG_SPL_OS_BOOT Activates/Deactivates the OS booting feature CONFIG_SPL_OS_BOOT_KEY defines the IO-pin number u-boot switch - if pressed u-boot is booted CONFIG_SYS_NAND_SPL_KERNEL_OFFS Offset in NAND of direct boot kernel image to use in SPL CONFIG_SYS_SPL_ARGS_ADDR Address where the kernel boot arguments are expected - this is normaly RAM-begin + 0x100 Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* omap-common: Add NAND SPL linux bootingSimon Schwarz2012-03-27-16/+50
| | | | | | | | | | | | | | | | This implements booting of Linux from NAND in SPL Related config parameters: CONFIG_SYS_NAND_SPL_KERNEL_OFFS Offset in NAND of direct boot kernel image to use in SPL CONFIG_SYS_SPL_ARGS_ADDR Address where the kernel boot arguments are expected - this is normally RAM-start + 0x100 (on ARM) Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* mx53: Make PLL2 to be the parent of UART clockFabio Estevam2012-03-27-3/+17
| | | | | | | | | | | | | | | | | | Change the parent UART clock to be PLL2, so that U-boot can also boot a Freescale 2.6.35 kernel for mx53. FSL kernel and U-boot changed the UART parent from PLL3 to PLL2 to avoid conflicts with IPU clocks, so that the video resolution can be changed without affecting the UART clock. On a 2.6.35 kernel the serial console is messed up after IPU driver is loaded and this patch fixes this problem. Tested on a mx53loco board booting a FSL kernel and also a mainline kernel. Reported-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
* mx6: Read silicon revision from registerFabio Estevam2012-03-27-3/+29
| | | | | | | | | | | | | | | Instead of hardcoding the mx6 silicon revision, read it in run-time. Also, besides the silicon version print the mx6 variant type: quad,dual/solo or solo-lite. Tested on a mx6qsabrelite, where it shows: CPU: Freescale i.MX6Q rev1.0 at 792 MHz Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <r64343@freescale.com>
* i.MX28: Drop __naked function from spl_mem_initMarek Vasut2012-03-27-7/+3
| | | | | | | | | | | | | Instead of compiling the function and using the result as a constant, simply use the constant. NOTE: This patch works around bug: http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52546 Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
* i.MX28: Make the stabilization delays shorterMarek Vasut2012-03-27-4/+4
| | | | | | | | | | | | | Cut down the VDDIO/VDDA regulator stabilization delays to 500 uS. That should be enough according to the datasheet and bootlets. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Robert Deliën <robert@delien.nl> Cc: Fabio Estevam <festevam@gmail.com> Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
* mx6: Fix reset cause for Power On Reset caseFabio Estevam2012-03-27-0/+1
| | | | | | | | | | | | | After booting mx6qsabrelite from POR the following is reported: CPU: Freescale i.MX61 family rev1.0 at 792 MHz Reset cause: unknown reset This is because both the POR and WDOG bits are set after reset. Fix this by also checking both bits in the POR case. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* i.MX28: Enable additional DRAM address bitsMarek Vasut2012-03-27-1/+1
| | | | | | | | Enables all fourteen address lines for DRAM Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Marek Vasut <marek.vasut@gmail.com>
* mx31: add "ARM11P power gating" to get_reset_causeHelmut Raiger2012-03-27-0/+2
| | | | | | Add missing reset reason 7 to get_reset_cause(). Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* IXP: Squash warnings in IXP NPEMarek Vasut2012-03-26-7/+1
| | | | | | | | | | | | | IxEthAcc.c: In function ‘ixEthAccInit’: IxEthAcc.c:105:21: warning: comparison between ‘IxEthDBStatus’ and ‘enum <anonymous>’ [-Wenum-compare] IxEthDBAPISupport.c: In function ‘ixEthDBPortAddressSet’: IxEthDBAPISupport.c:633:18: warning: variable ‘ackPortAddressLock’ set but not used [-Wunused-but-set-variable] IxQMgrDispatcher.c: In function ‘ixQMgrLLPShow’: IxQMgrDispatcher.c:1194:18: warning: variable ‘q’ set but not used [-Wunused-but-set-variable] Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* IXP: Make IXP buildable with arm-linux- toolchainsMarek Vasut2012-03-26-0/+3
| | | | | | | | | | | Add -EB flag to LD to switch endianness of the linker. This should make armeb targets buildable again. Also, make use of U-Boot's internal libgcc instead of toolchain's one, this works around the use of libraries from GCC, which might be little endian. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* SPL: Add YMODEM over UART load supportMatt Porter2012-03-26-0/+84
| | | | | | | | | | Adds support for loading U-Boot from UART using YMODEM protocol. If YMODEM support is enabled in SPL and the romcode indicates that SPL loaded via UART then SPL will wait for start of a YMODEM transfer via the console port. Signed-off-by: Matt Porter <mporter@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
generated by cgit v1.1 at 2024-11-15 15:23:06 +0000