summaryrefslogtreecommitdiff
path: root/arch/arm/cpu
Commit message (Collapse)AuthorAgeLines
* armv8/fsl-lsch3: consolidate the clock system initializationHou Zhiqiang2017-01-18-7/+21
| | | | | | | | This patch binds the sys_info->freq_systembus to Platform PLL, and implements the IPs' clock function individually. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8/fsl-lsch2: refactor the clock system initializationHou Zhiqiang2017-01-18-18/+131
| | | | | | | | | | | | | | | | | | | Up to now, there are 3 kind of SoCs under Layerscape Chassis 2, like LS1043A, LS1046A and LS1012A. But the clocks tree has a lot of differences, for instance, the IP modules have different dividers to derive its clock from Platform PLL. And the core cluster PLL and platform PLL maybe have different reference clocks, such as LS1012A. Another problem is which clock/PLL should be described by sys_info->freq_systembus, it is confused in Layerscape Chissis 2. This patch is to bind the sys_info->freq_systembus to the Platform PLL, and handle the different divider of IP modules separately between different SoCs, and separate reference clocks of core cluster PLL and platform PLL. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* ARMv8/fsl-layerscape: Enable data coherency between cores in clusterHou Zhiqiang2017-01-18-0/+4
| | | | | Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: Enable CPUECTLR.SMPEN for coherencyMingkai Hu2017-01-18-0/+29
| | | | | | | | | | | | | | | | | | For A53, data coherency is enabled only when the CPUECTLR.SMPEN bit is set. The SMPEN bit should be set before enabling the data cache. If not enabled, the cache is not coherent with other cores and data corruption could occur. For A57/A72, SMPEN bit enables the processor to receive instruction cache and TLB maintenance operations broadcast from other processors in the cluster. This bit should be set before enabling the caches and MMU, or performing any cache and TLB maintenance operations. Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8/fsl_lsch2: Add the OCRAM initializationHou Zhiqiang2017-01-18-0/+37
| | | | | | | | | | | | | | Clear the content to zero and the ECC error bit of OCRAM1/2. The OCRAM must be initialized to ZERO by the unit of 8-Byte before accessing it, or else it will generate ECC error. And the IBR has accessed the OCRAM before this initialization, so the ECC error status bit should to be cleared. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* kconfig: move FSL_PCIE_COMPAT to platform KconfigHou Zhiqiang2017-01-18-0/+19
| | | | | | Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: fsl-layerscape, ccn504: Set forced-order mode in RNI-6, RNI-20Priyanka Jain2017-01-18-0/+20
| | | | | | | | | | | | It is recommended to set forced-order mode in RNI-6, RNI-20 for performance optimization in LS2088A. Both LS2080A, LS2088A families has CONFIG_LS2080A define. As above update is required only for LS2088A, skip this for LS2080A SoC family. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to KconfigYork Sun2017-01-04-9/+0
| | | | | | | | Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing usage in ls102xa and fsl-layerscape. Remove all powerpc macros in config header and board header files. Signed-off-by: York Sun <york.sun@nxp.com>
* arm: layerscape: Move CONFIG_SYS_FSL_ERRATUM_* to KconfigYork Sun2017-01-04-0/+48
| | | | | | Use Kconfig to select errata workaround. Signed-off-by: York Sun <york.sun@nxp.com>
* fsl_ddr: Move DDR config options to driver KconfigYork Sun2017-01-04-93/+11
| | | | | | | | | Create driver/ddr/fsl/Kconfig and move existing options. Clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com> [trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s] Signed-off-by: Tom Rini <trini@konsulko.com>
* crypto: Move CONFIG_SYS_FSL_SEC_LE and _BE to KconfigYork Sun2017-01-04-0/+3
| | | | | | | Use Kconfig option to set little- or big-endian access to secure boot and trust architecture. Signed-off-by: York Sun <york.sun@nxp.com>
* crypto: Move SYS_FSL_SEC_COMPAT into driver KconfigYork Sun2017-01-04-0/+6
| | | | | | | Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC and ARM SoCs, move it to Kconfig under the driver. Signed-off-by: York Sun <york.sun@nxp.com>
* ARM64: zynqmp: Add missing SPL dependency for boot.bin generationMichal Simek2016-12-20-0/+1
| | | | | | | boot.bin file is generated only when SPL is selected. Reflect this depency in Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* ARM: mxs: Remove unused variable warningMarek Vasut2016-12-19-2/+2
| | | | | | | | | | | | | Shuffle the macros around a little to remove the following warning when building for i.MX28: arch/arm/cpu/arm926ejs/mxs/spl_boot.c:44:26: warning: ‘iomux_boot’ defined but not used [-Wunused-const-variable=] static const iomux_cfg_t iomux_boot[] = { ^~~~~~~~~~ Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Stefano Babic <sbabic@denx.de>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-12-18-32/+182
|\ | | | | | | | | | | Migrate CONFIG_ARCH_USE_MEMSET/MEMCPY with this merge. Signed-off-by: Tom Rini <trini@konsulko.com>
| * imx6: icorem6_rqs: Add FEC supportJagan Teki2016-12-16-0/+1
| | | | | | | | | | | | | | | | | | Add FEC support for Engicam i.CoreM6 RQS modules. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * imx6: geam6ul: Add FEC supportJagan Teki2016-12-16-0/+1
| | | | | | | | | | | | | | | | | | Add FEC support for Engicam GEAM6UL module. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * imx6: icorem6_rqs: Add I2C supportJagan Teki2016-12-16-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add I2C support for Engicam i.CoreM6 RQS modules. icorem6qdl-rqs> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 icorem6qdl-rqs> i2c dev 0 Setting bus to 0 icorem6qdl-rqs> i2c speed 100000 Setting bus speed to 100000 Hz icorem6qdl-rqs> i2c probe Valid chip addresses: 4F icorem6qdl-rqs> i2c md 4F 0xff 00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ icorem6qdl-rqs> i2c bus Bus 0: i2c@021a0000 (active 0) 4f: generic_4f, offset len 1, flags 0 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial supportJagan Teki2016-12-16-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot from MMC: ------------- U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44) Trying to boot from MMC1 U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 icorem6qdl-rqs> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * imx6: geam6ul: Add I2C supportJagan Teki2016-12-16-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add I2C support for Engicam GEAM6UL module. geam6ul> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 geam6ul> i2c dev 0 Setting bus to 0 geam6ul> i2c dev Current bus is 0 geam6ul> i2c speed 100000 Setting bus speed to 100000 Hz geam6ul> i2c probe Valid chip addresses: 2C geam6ul> i2c md 2C 0xff 00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........ Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial supportJagan Teki2016-12-16-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Boot Log: -------- U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30) Trying to boot from MMC1 U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 43C Reset cause: POR Model: Engicam GEAM6UL DRAM: 128 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 geam6ul> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * imx6: icorem6: Add I2C supportJagan Teki2016-12-16-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add I2C support for Engicam i.CoreM6 qdl board. icorem6qdl> i2c bus Bus 0: i2c@021a0000 Bus 1: i2c@021a4000 Bus 2: i2c@021a8000 icorem6qdl> i2c dev 2 Setting bus to 2 icorem6qdl> i2c speed 100000 Setting bus speed to 100000 Hz icorem6qdl> i2c probe Valid chip addresses: 2C icorem6qdl> i2c md 2C 0xff 00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00 .......d........ Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Heiko Schocher <hs@denx.de>
| * icorem6: Use CONFIG_DM_ETH supportJagan Teki2016-12-16-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Use CONFIG_DM_ETH and remove board_eth_init code from board files. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
| * arm: imx: add i.MX53 Beckhoff CX9020 Embedded PCPatrick Bruenn2016-12-16-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
| * arm: imx: add i.MX6SLL EVK board supportPeng Fan2016-12-16-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add i.MX6SLL EVK board support. 1. Add imx6sll-evk device tree. 2. Enable SDHC/I2C/UART. 3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver. Boot Log: U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800) CPU: Freescale i.MX6SLL rev1.0 at 792MHz CPU: Commercial temperature grade (0C to 95C)Reset cause: POR Model: Freescale i.MX6SLL EVK Board Board: MX6SLL EVK DRAM: 2 GiB i2c bus 0 at 35258368, no gpio pinctrl state. PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * imx: mx6sll: add Kconfig entry for i.MX6SLLPeng Fan2016-12-16-0/+4
| | | | | | | | | | | | add Kconfig entry for i.MX6SLL Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * imx: mx6sll: add clock supportPeng Fan2016-12-16-7/+21
| | | | | | | | | | | | | | Add clock support for i.MX6SLL. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * imx: clock: gate clk before changing pix clk muxPeng Fan2016-12-16-20/+30
| | | | | | | | | | | | | | | | | | | | | | The LCDIF Pixel clock mux is not glitchless, so need to gate before changing mux. Also change enable_lcdif_clock prototype with a new input parameter to indicate disable or enable. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * imx: mx6sl: add lcdif clock supportPeng Fan2016-12-16-19/+59
| | | | | | | | | | | | Add lcdif clock support for i.MX6SL. Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * imx: mx6: lcdif: gate clock before changing muxPeng Fan2016-12-16-0/+10
| | | | | | | | | | | | | | | | The mux for the lcd clock is not glitchless, so need to first gate the clock before changing the mux. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * imx: mx6: fix mmdc ch0 clk for 6SLPeng Fan2016-12-16-0/+5
| | | | | | | | | | | | | | | | | | | | >From RM, per_periph2_clk_sel option3 is: "derive clock from 198MHz clock (divided 392MHz PLL2 PFD)." So fix it. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * board/liteboard: Add support for liteBoardMarcin Niestroj2016-12-16-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | liteBoard is a development board which uses liteSOM as its base. Hardware specification: * liteSOM (i.MX6UL, DRAM, eMMC) * Ethernet PHY (id 0) * USB host (usb_otg1) * MicroSD slot (uSDHC1) Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
| * udoo_neo: Add thermal supportBreno Lima2016-12-16-0/+2
| | | | | | | | | | | | | | Add thermal support on the Kconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * udoo_neo: Move MX6SX configuration to KconfigBreno Lima2016-12-16-0/+1
| | | | | | | | | | | | | | | | | | It's not necessary to define the processor in the defconfig file. The preferred method to select the SoC is via Kconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * arm: imx: initial support for colibri imx6Max Krummenacher2016-12-16-0/+8
| | | | | | | | | | | | | | | | This adds board support for the Toradex module family Colibri iMX6. The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both with a version for commercial and industrial temperature range. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
| * arm: imx: initial support for apalis imx6Max Krummenacher2016-12-16-0/+8
| | | | | | | | | | | | | | | | This adds board support for the Toradex module family Apalis iMX6. The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with commercial and industrial temperature range. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
* | ARMv8: LS1043A: Enable LS1043A default PSCI supportmacro.wave.z@gmail.com2016-12-15-0/+21
| | | | | | | | | | | | | | | | | | | | A most basic PSCI implementation with only one psci_version is added for LS1043A, this can verify the generic PSCI framework, and more platform specific implementation will be added later. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | ARMv8: Setup PSCI memory and device treemacro.wave.z@gmail.com2016-12-15-1/+32
| | | | | | | | | | | | | | | | | | Newly add ARMv8 PSCI needs to be initialized, be copied or reserved in right place, this patch does all the setup steps. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | ARMv8: Add basic PSCI frameworkmacro.wave.z@gmail.com2016-12-15-0/+297
| | | | | | | | | | | | | | | | | | | | This patch introduces a generic ARMv8 PSCI framework, with all functions returning a dummy ARM_PSCI_RET_NI (Not Implemented), then it is up to each platform to implement their own functions based on this framework. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | ARMv8: Add secure sections for PSCI text and datamacro.wave.z@gmail.com2016-12-15-0/+89
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds secure_text, secure_data and secure_stack sections for ARMv8 to hold PSCI text and data, and it is based on the legacy implementation of ARMv7. ARMV8_SECURE_BASE defines the address for PSCI secure sections, ARMV8_PSCI and ARMV8_PSCI_NR_CPUS are firstly used in this patch, so they are introduce here in Kconfig too. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | ARMv8: LS1043A: change macro CONFIG_ARMV8_PSCI definitionmacro.wave.z@gmail.com2016-12-15-5/+27
|/ | | | | | | | | | | | NXP/Freescale uses macro CONFIG_ARMV8_PSCI to enable their private PSCI implementation in PPA firmware, but this macro naming too generic, so this patch replaces it with a specic one CONFIG_FSL_PPA_ARMV8_PSCI. And this macro CONFIG_ARMV8_PSCI will be used for a generic PSCI for ARMv8 which will be added in following patchs. Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
* arm: armv7: add us timer for bootstagePatrick Delaunay2016-12-09-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | solve issue when bootstage is used with armV7 generic timer first call of timer_get_boot_us() use the function get_timer() before timer initialization (arch.timer_rate_hz = 0) => div by 0 Commit-notes When I activate bootstage on ARMV7 architecture with platform using the generic armv7 timer defined in file ./arch/arm/cpu/armv7m/timer.c I have a issue because gd->arch.timer_rate_hz = 0 For me the get_timer() function should not used before timer_init (which initialize gd->arch.timer_rate_hz) at least for the ARMV7 timer. But in the init sequence, the first bootstage fucntion is called before timer_init and this function use the timer function. For me it is a error in the generic init sequence : mark_bootstage is called before timer_init. static init_fnc_t init_sequence_f[] = { .... arch_cpu_init_dm, mark_bootstage, /* need timer, go after init dm */ ... #if defined(CONFIG_ARM) || defined(CONFIG_MIPS) || \ defined(CONFIG_BLACKFIN) || defined(CONFIG_NDS32) || \ defined(CONFIG_SPARC) timer_init, /* initialize timer */ #endif ....... To solve the issue for all the paltform, we can move timer_init() call just before mark_bootstage() in this array... It should be ok for ARMV7 but I don't sure for other platform impacted - the other ARM platform or ARMV7 wich don't use generic timer - MIPS BLACKFIN NDS32 or SPARC and I don't sure of impact for other function called (board_early_init_f for example....) => This patch solve issue only in timer armv7 get_boot_us() can be called everytime without div by 0 issue (gd->arch.timer_rate_hz is not used) END Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* armv8: QSPI: Add AHB bus 16MB+ size supportYuan Yao2016-12-05-0/+49
| | | | | | | | The default configuration for QSPI AHB bus can't support 16MB+. But some flash on NXP layerscape board are more than 16MB. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls2080a: Add serdes1 protocol 0x3b supportPriyanka Jain2016-12-05-0/+1
| | | | | Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* fsl/ddr: Add erratum_a009942_check_cpo and clean related erratumShengzhou Liu2016-12-05-1/+6
| | | | | | | | | | | | | - add additional function erratum_a009942_check_cpo to check if the board needs tuning CPO calibration for optimal setting. - move ERRATUM_A009942(with revision to check cpo_sample option) from fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts. - move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c - remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> [YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500] Reviewed-by: York Sun <york.sun@nxp.com>
* Merge git://git.denx.de/u-boot-mpc85xxTom Rini2016-12-04-0/+11
|\
| * armv8: fsl-layerscape: Move SECURE_BOOT to KconfigYork Sun2016-12-02-0/+5
| | | | | | | | | | | | Move from CONFIG_SYS_EXTRA_OPTIONS to Kconfig option. Signed-off-by: York Sun <york.sun@nxp.com>
| * armv7: ls1021a: Move SECURE_BOOT option to KconfigYork Sun2016-12-02-0/+6
| | | | | | | | | | | | Move from CONFIG_SYS_EXTRA_OPTIONS to Kconfig option. Signed-off-by: York Sun <york.sun@nxp.com>
* | ARM64: zynqmp: List secondary software boot modesMichal Simek2016-12-02-0/+12
| | | | | | | | | | | | | | | | Using alternative bootmode field to support automatic secondary boot modes. It is purely software setting where SW modes are using free bootmode combinations. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | ARM64: zynqmp: Force certain bootmode for SPLMichal Simek2016-12-02-1/+1
| | | | | | | | | | | | | | | | ZynqMP provides an option to overwrite bootmode setting which can change SPL behavior. For example: boot SPL via JTAG and then SPL loads images from SD. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit v1.1 at 2024-10-30 15:36:46 +0000