summaryrefslogtreecommitdiff
path: root/arch/arm/cpu
Commit message (Collapse)AuthorAgeLines
* socfpga: Adding Freeze Controller driverChin Liang See2013-12-03-1/+225
| | | | | | | | | | | | | | Adding Freeze Controller driver. All HPS IOs need to be in freeze state during pin mux or IO buffer configuration. It is to avoid any glitch which might happen during the configuration from propagating to external devices. Signed-off-by: Chin Liang See <clsee@altera.com> Cc: Wolfgang Denk <wd@denx.de> CC: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
* Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD2013-12-02-4/+340
|\
| * arm926ejs, at91: add common phy_reset functionHeiko Schocher2013-12-01-0/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | add common phy reset code into a common function. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com> Cc: Jens Scharsig <esw@bus-elektronik.de> Cc: Sergey Lapin <slapin@ossfans.org> Cc: Stelian Pop <stelian@popies.net> Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com> Cc: Eric Benard <eric@eukrea.com> Cc: Markus Hubig <mhubig@imko.de> Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Tested-by: Bo Shen <voice.shen@atmel.com> Acked-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * arm: atmel: sama5d3: spl boot from fat fs SD cardBo Shen2013-12-01-2/+142
| | | | | | | | | | | | | | | | Enable Atmel sama5d3xek boart spl boot support, which can load u-boot from SD card with FAT file system. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * arm: atmel: add ddr2 initialization functionBo Shen2013-12-01-0/+136
| | | | | | | | | | | | | | | | The MPDDRC supports different type of SDRAM This patch add ddr2 initialization function Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * arm: atmel: sama5d3: correct the ID for DBGU and PITBo Shen2013-12-01-2/+2
| | | | | | | | | | | | | | | | As the DBGU and PIT has its own ID on sama5d3 SoC, while not share with SYS ID. So, correct them. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * ARM: at91: sama5d3: add support for sama5d36 chipWu, Josh2013-11-13-1/+3
| | | | | | | | | | | | | | | | | | | | | | The SAMA5D36 chip is the superset product of SAMA5D3x family. For detail information please refer to: http://www.atmel.com/Microsite/sama5d3/default.aspx Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* | Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master'Albert ARIBAUD2013-11-22-4/+5
|\ \ | |/ |/|
| * arm: zynq : Revert TZ_DDR_RAM to secure.Radhey Shyam Pandey2013-11-06-2/+0
| | | | | | | | | | | | | | | | | | | | TZ_DDR_RAM on reset is in secure mode. Since uboot and linux runs in full TZ privilege secure mode, no need to set DDR trustzone to non-secure. Signed-off-by: Radhey Shyam Pandey <radheys@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * arm: zynq: Do not remap OCM to high addressMichal Simek2013-11-06-2/+5
| | | | | | | | | | | | | | | | In case where ps-ddr is not used, do not remap OCM to high address and keep it from 0x0. Linux SMP requires to have memory at 0x0. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | arm, am33x: make RTC32K OSC enable configurableHeiko Schocher2013-11-11-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | As http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast states: "Initialize devices only when they are needed within U-Boot" enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is enabled. Enable this in ti_am335x_common.h, so all boards in mainline should work as before. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
* | Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-09-32/+82
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
| * \ Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-07-29/+69
| |\ \ | | |/ | |/|
| | * ARM: mxs: Enable DCDC converter for battery bootMarek Vasut2013-10-31-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In case the board detected sufficient voltage for battery boot, make sure the DCDC converter is ON and the board is not running only from linregs, otherwise an instability will be observed. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
| | * mx5: lowlevel_init: Remove unused macroFabio Estevam2013-10-31-6/+0
| | | | | | | | | | | | | | | | | | | | | setup_wdog macro is not used anywhere, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| | * ARM: mx5: Enable L2 cacheFabio Estevam2013-10-31-0/+6
| | | | | | | | | | | | | | | | | | Enable L2 cache for improving the system performance. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| | * ARM: mxs: Setup stack in JTAG modeMarek Vasut2013-10-17-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In case the MX23/MX28 is switched into JTAG mode via the BootMode select switches, the BootROM bypasses the CPU core registers initialization. This in turn means that the Stack Pointer (SP) register is not set as it is in every other mode of operation, but instead is only zeroed out. To prevent U-Boot SPL from crashing in this obscure JTAG mode, configure the SP to point at the CONFIG_SYS_INIT_SP_ADDR if the SP is zeroed out. Note that in case the SP is already configured, we must preserve that exact SP value and must not modify it. This is important since in every other mode but the JTAG mode, the SPL returns into the BootROM and BootROM in turn loads U-Boot itself. If the SP were to be corrupted, the BootROM won't be able to continue it's operation after returned from SPL and the system would crash. Finally, add the JTAG mode switch identifier, so it's not recognised as Unknown mode. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
| | * ARM: mxs: tools: Use mkimage for BootStream generationMarek Vasut2013-10-17-9/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that mkimage can generate an BootStream for i.MX23 and i.MX28, use the mkimage as a default tool to generate the BootStreams instead of the elftosb tool. This cuts out another obscure dependency. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| | * mx6: compute PLL PFD frequencies rather than using definesPierre Aubert2013-10-17-14/+42
| | | | | | | | | | | | | | | Signed-off-by: Pierre Aubert <p.aubert@staubli.com> CC: Stefano Babic <sbabic@denx.de>
| * | am335x: Enable CONFIG_OMAP_WATCHDOG supportTom Rini2013-11-01-0/+4
| | | | | | | | | | | | | | | | | | | | | There is a board-specific portion for calling watchdog enable itself, in main U-Boot. Signed-off-by: Tom Rini <trini@ti.com>
| * | am33xx, davinci: Create and use <asm/davinci_rtc.h>Tom Rini2013-11-01-3/+4
| |/ | | | | | | | | | | | | Create a common header file for the RTC IP block that is shared between davinci and am33xx. Signed-off-by: Tom Rini <trini@ti.com>
| * zynq: Use arch_cpu_init() instead of lowlevel_init()Michal Simek2013-10-17-0/+6
| | | | | | | | | | | | | | | | | | | | | | Zynq lowlevel_init() was implemented in C but stack pointer is setup after function call in _main(). Move architecture setup to arch_cpu_init() which is call as the first function in board_init_f() which already have correct stack pointer. Reported-by: Sven Schwermer <sven.schwermer@tuhh.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | ARM: versatile: convert to common timer codeRob Herring2013-11-04-116/+0
| | | | | | | | | | | | Convert versatile to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* | ARM: tegra: convert to common timer codeRob Herring2013-11-04-96/+1
| | | | | | | | | | | | Convert tegra to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* | ARM: socfpga: convert to common timer codeRob Herring2013-11-04-72/+0
| | | | | | | | | | | | Convert socfpga to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* | ARM: mx25: convert to common timer codeRob Herring2013-11-04-117/+0
| | | | | | | | | | | | Convert mx25 to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* | ARM: highbank: convert to common timer codeRob Herring2013-11-04-83/+0
| | | | | | | | | | | | Convert highbank to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* | ARM: s5pc, exynos: move Samsung ARM SoC specific code under arch/arm/Masahiro Yamada2013-10-31-0/+4
| | | | | | | | | | | | | | | | | | This patch moves S5PC, EXYNOS specific directory entries from the toplevel Makefile to arch/arm/cpu/armv7/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
* | ARM: omap: move OMAP specific code under arch/arm/Masahiro Yamada2013-10-31-0/+3
| | | | | | | | | | | | | | | | | | This patch moves OMAP specific directory entries from the toplevel Makefile and spl/Makefile to arch/arm/cpu/armv7/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
* | ARM: tegra: move Tegra specific code under arch/arm/Masahiro Yamada2013-10-31-0/+6
| | | | | | | | | | | | | | | | | | This patch moves Tegra specific directory entries from the toplevel Makefile and spl/Makefile to arch/arm/cpu/*/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Warren <TWarren@nvidia.com>
* | ARM: convert makefiles to Kbuild styleMasahiro Yamada2013-10-31-369/+39
| | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | arm720t: convert makefiles to Kbuild styleMasahiro Yamada2013-10-31-114/+8
| | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | arm920t: convert makefiles to Kbuild styleMasahiro Yamada2013-10-31-170/+22
| | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | arm926ejs: convert makefiles to Kbuild styleMasahiro Yamada2013-10-31-407/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Note1: In arch/arm/cpu/arm926ejs/spear/Makefile START := start.o was changed extra-$(CONFIG_SPL_BUILD) := start.o because spear/start.o is only used for SPL. Note2: START := start.o was missing from arch/arm/cpu/arm926ejs/mxs/Makefile. This commit simply adds extra-$(CONFIG_SPL_BUILD) := start.o Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | armv7: convert makefiles to Kbuild styleMasahiro Yamada2013-10-31-581/+103
| | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini2013-10-21-2/+29
|\ \
| * | usb: dra7xx: Add support for dra7xx xhci USB hostDan Murphy2013-10-20-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the support for the dra7xx xhci usb host. dra7xx does not contain an EHCI controller so the headers can be removed from the board file. The xHCI host on dra7xx is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
| * | ARM: OMAP5: Add registers and defines for USBOTG SSDan Murphy2013-10-20-2/+6
| | | | | | | | | | | | | | | | | | | | | Add the prcm registers and the bit definitions to enable the USB SS port of the OMAP5 device. Signed-off-by: Dan Murphy <dmurphy@ti.com>
| * | arm: exynos: Add methods to control power to USB 3.0 PHYVivek Gautam2013-10-20-0/+22
| |/ | | | | | | | | | | | | | | | | | | | | | | Adding methods to turn on/off power to USB3.0 type PHY as and when required by the controller. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Vasut <marex@denx.de>
* | i2c: mxc: move to new subsystemtrem2013-10-17-2/+2
|/ | | | Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
* Coding Style cleanup: drop some excessive empty linesWolfgang Denk2013-10-14-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Coding Style cleanup: remove trailing empty linesWolfgang Denk2013-10-14-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Coding Style cleanup: replace leading SPACEs by TABsWolfgang Denk2013-10-14-22/+22
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Drop changes for PEP 4 following python tools] Signed-off-by: Tom Rini <trini@ti.com>
* Coding Style cleanup: remove trailing white spaceWolfgang Denk2013-10-14-24/+24
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* ARM: omap4: Update sdram setting for panda rev A6Dan Murphy2013-10-14-0/+4
| | | | | | | | | | OMAP4 panda rev A6 is a 4430 es2.3 IC with an updated memory part. The panda rev A6 uses Elpida 2x4Gb memory and no longer uses Micron so the timings needs to be updated Signed-off-by: Dan Murphy <dmurphy@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-10-08-609/+34
|\
| * socfpga: Adding System Manager driverChin Liang See2013-10-07-1/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adding System Manager driver which will configure the pin mux for real hardware Cyclone V development kit (not Virtual Platform) Signed-off-by: Chin Liang See <clsee@altera.com> Reviewed-by: Pavel Machek <pavel@denx.de> Acked-by: Dinh Nguyen <dinguyen@altera.com> Cc: Wolfgang Denk <wd@denx.de> CC: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
| * omap1510inn: arm925t: remove supportAlbert ARIBAUD2013-10-07-608/+0
| | | | | | | | | | | | | | | | | | omap1510inn is orphan and has been for years now. Reove it and, as it was the only arm925t target, also remove arm925t support. Update doc/README.scrapyard accordingly. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini2013-10-08-1/+10
|\ \
| * | armv7: hw_data: change clock divider setting.Poddar, Sourav2013-10-07-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clock requirement for qspi clk is 192 Mhz. According to the below formulae, f dpll = f ref * 2 * m /(n + 1) clockoutx2_Hmn = f dpll / (hmn+ 1) fref = 20 Mhz, m = 96, n = 4 gives f dpll = 768 Mhz For clockoutx2_Hmn to be 768, hmn + 1 should be 4. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
generated by cgit v1.1 at 2024-10-16 10:26:55 +0000